During springterm 2010 Erik Persson and Magnus Hansson performed their ThesisWork with DIAB Laholm, in Hallands County for University of Halmstad.The project has been a product development project without exterior customers. Thusit had a great emphasis on functionality and less emphasis on marketing and such.This reflects the ambition to develop machinery to be used within the productionfacilities of DIAB Laholm, not to be sold to exterior customers.Main objective has been to create machinery which enables the production ofrotational symmetric work pieces within a NC-Milling machine with 5 axles. Thework pieces milled will be made of DIAB?s material Divyncell with varyingdensities.The project has followed Fredy Olssons method involving Principal ? Primary ?Manufacturing constructions. However a complete manufacturing construction hasnot been made since DIAB just wanted a good Primary construction which will serveas a base for finishing touches at DIAB.By the end of the project material including calculations has been sent to DIAB andthey will finish the work and manufacture the machine if they find economic viabilityin this.The work method has been suited for this by several reasons, it was created withthese projects in mind and it?s also the method most familiar to us..

During springterm 2010 Erik Persson and Magnus Hansson performed their ThesisWork with DIAB Laholm, in Hallands County for University of Halmstad.The project has been a product development project without exterior customers. Thusit had a great emphasis on functionality and less emphasis on marketing and such.This reflects the ambition to develop machinery to be used within the productionfacilities of DIAB Laholm, not to be sold to exterior customers.Main objective has been to create machinery which enables the production ofrotational symmetric work pieces within a NC-Milling machine with 5 axles. Thework pieces milled will be made of DIAB?s material Divyncell with varyingdensities.The project has followed Fredy Olssons method involving Principal ? Primary ?Manufacturing constructions. However a complete manufacturing construction hasnot been made since DIAB just wanted a good Primary construction which will serveas a base for finishing touches at DIAB.By the end of the project material including calculations has been sent to DIAB andthey will finish the work and manufacture the machine if they find economic viabilityin this.The work method has been suited for this by several reasons, it was created withthese projects in mind and it?s also the method most familiar to us..

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

Detta examensarbete har utförts på uppdrag av Koenigsegg Automotive AB, som utvecklar, tillverkar och säljer högpresterande sportbilar. Företaget erbjuder fälgar tillverkade helt i kolfiberkomposit, som ger betydande viktbesparingar i jämförelse med traditionella metallfälgar.Efter tillverkningen kräver fälgarna viss bearbetning vid anläggningsytan mellan fälg och däck. Syftet med examensarbetet har varit att undersöka möjligheten att utföra bearbetningen av fälgarna in-house i Ängelholm, och målet har varit att konstruera en maskin för detta ändamål.Projektet inleddes med en litteratursökning, där svårigheter och möjligheter gällande bearbetning av kolfiberkompositer undersöktes. Till följd av de undersökningar som gjordes, valdes bearbetningsmetoden svarvfräsning och ett antal konstuktionskoncept genererades. Genom ett antal utvärderingar utvecklades ett speciellt koncept vidare till ett komplett produktförslag.Produktförslaget är komplett med analyser, beräkningar samt tillverkningsunderlag, som ger uppdragsgivaren bättre insikt i sina möjligheter.

The unique ability of wheat to produce leavened bread is mainly due to the gluten proteins present. As consumers are more and more attracted to bread with high fibre content the use of wheat gluten will also increase in order to obtain bread with good volume and appetizing characteristics. Air-classification is a technological method used to separate particles by size and shape by means of air-streams into two fractions, fine and coarse. When used on wheat flour it is known to alter the flour composition in the fractions obtained compared to the original flour. This method is not widely used in the Milling industry but could possibly be of interest if protein rich fractions with favorable protein quality can be produced.

Fuel pellets are in Sweden mainly produced from sawdust and cutter shavings. Before the pelletising process the raw material is dried to attain consistent moisture content and ground up in a hammer mill. In the densification process (pelletising) the ground material is forced through holes in a rotating die. This heats up the wood particles which cause them to soften and self bond. After the process the pellets are cooled, sieved and bagged. The Milling process creates a wide range of particle sizes.

This thesis work is made by Torbjörn Johansson on Karlstad University for Uddeholms AB. The assignment in this thesis work was to investigate tough cutting in three different tool steels: Vanadis 4 Extra, Vancron 40 and Sverker 21. The research was to compare the wear of the tool after cutting in each one of the tool steel alloys. The research was also made to see if the tool cutting in Vancron 40 has a better wear than the tool cutting in Vanadis 4 Extra and also compare the results with Sverker 21. All three of these alloys are a part of Uddeholms AB:s range of products, and is used in applications like forming tools and knife tools. Vancron 40 is a powder steel with a very good combination of mechanical properties like ductility, adhesive strength and hardness.

Among farmers in Sweden hedging of product prices is a relatively new way of thinking. A deregulated market and a more volatile price picture are consequences of the free market and the movements towards globalization. The effects of globalization are largely a demand- and supply driven market. These factors give the farmers incentives to stay informed and to act on their own in order to manage their price risk exposure.The overall purpose with this study is to analyze the farmers? attitudes and awareness of price hedging and to examine what type of decision processes that characterize hedging decisions.The study covers the period 2006 until 2008 and the crops oil seeds, barley (malt), Milling wheat, feed wheat, oats and feed oats.

I denna rapport beskrivs en undersökning och jämförelse av två olika sorters segjärn. Detvå materialen som har studerats har varit det segjärnet som används i Parker Hannifinsnuvarande hydraulikmotorer och ett nytt segjärn, vars mekaniska egenskaper har påståttsvara mer fördelaktiga. Målet med arbetet var att få fram en tillförlitlig jämförelse av de olikamaterialen och avgöra om det fanns ett tydligt underlag för att inleda processen av ett byteav material i vissa komponenter i Parker Hannifins produkter.Det utfördes jämförelser mellan de olika materialens mekaniska egenskaper baserade delspå information som redan fanns om materialen och dels på data insamlad vid tester medskärande bearbetning. Förslitning på verktygen vid fräsning studerades tillsammans medskärkraften med olika sorters skärdata. Restspänningar efter ingreppen i de båda materialenmättes med en röntgendiffraktometer.Resultaten gav inga signifikanta indikationer på att ett materialbyte skulle innebära en lägreproduktionskostnad, dock visade analyser att det nya materialet tål att bearbetas fortare ändet traditionella segjärnet och att fler undersökningar bör göras.

GE Healthcare wants to investigate whether additive manufacturing would be an alternative method in their workshops in the Umea? plant. Additive manufacturing is called 3D printing in everyday language and manufactures details by building them up layer by layer in an automated machine. The purpose of this work is therefore to investigate how mature additive manufacturing methods are and how they could be used at GE.The work has been divided into three parts. The first section investigates how additive manufacturing would work in the production workshop at GE.

GE Healthcare wants to investigate whether additive manufacturing would be an alternative method in their workshops in the Umea? plant. Additive manufacturing is called 3D printing in everyday language and manufactures details by building them up layer by layer in an automated machine. The purpose of this work is therefore to investigate how mature additive manufacturing methods are and how they could be used at GE.The work has been divided into three parts. The first section investigates how additive manufacturing would work in the production workshop at GE.