This thesis describes a conceptual design of a support frame for a synchronousgenerator used in a vertical axis wind power plant. In this system the generator isplaced on ground level. The thesis also considers the design of housing for thesupport frame and generator. The concept presented in this report is based on anearlier design. Besides geometric design, simplified simulations has been run in orderto optimize some of the parts included in the construction considering naturalfrequencies and structural strength.The result is presented as CAD-models andan assembly drawing..

This thesis work is the last part of the Master of Science education inmechanical engineering at KTH, Stockholm.The aim of this project was the development of a Multi-zone modelfor NOxformation in Diesel engines. Because of the stringent emissionlegislations, great effort is made to decrease the fuel consumption and theharmful emissions of internal combustion engines. Computer simulationsplay a decisive role in this context because they substitute the expensiveand time-consuming laboratory tests.The model is based on a multi-zone approach and uses the wellknownExtended Zeldovich Mechanism which gives a relation to calculatethe NO formation rate using the concentration of different gas speciesinvolved in the process.All the most important phenomena involved in the Diesel combustionhave been modelled. A special attention is then paid to the equilibriumconcentration calculation; this is a significant part of the model whichstrongly influences the following steps.A Simulink model has also been developed. This second version isbased on the previous model and it is made especially to allow theconnection with other external softwares, GT-power in this case.

This thesis investigates the underlying factors behind sexual risk-taking and non-risk-taking behavior with regard to Sexual Reproductive Health (SRH) among adolescents in Lusaka, Zambia. The Qualitative Approach was used for data collection and analysis and using the theory of Social Construction, the author explains how different contexts and aspects in the Zambian Society, that is Traditional, Socio-economic, Political, etc., influence the sexuality or sexual behavior of young people in Zambia. Hermeneutics was used to interpret the meanings in the texts/transcripts acquired through data collection and from the author?s knowledge and understanding of the Zambian historical and cultural contexts within which the participants of the research were constructed. Max Weber?s Ideal Type concept was also used to explain that each young individual?s sexual behavior is uniquely constructed by societal aspects.

Lansen Technology is a security company from Halmstad, Sweden and their focus indeveloping and selling alarm solutions. One of their latest inventions is a vibration sensor thatrecognizes very small movements in the ground.The thesis work was made in cooperation with Lansen Technology AB and the task was toinvent a test equipment that decides whether the sensor is working correctly. By generatingcertain frequencies with specific amplitude, we will expect the sensor to give a similar output.The final report includes all the parts of our work as studying, choosing components,programming, construction, results and conclusion..

Följande rapport bygger på examensarbetet inom CAD-teknikerprogrammet påHögskolan i Halmstad. Arbetet innefattar framtagning av ett höjdjusterbartarmstöd till bilförare, en produkt som inte finns på marknaden idag.Utförandet av arbetet har bl.a. inneburit kriterieuppställning med krav ochönskemål, framtagning av produktförslag i form utav skisser och 3D-modeller, valav material genom undersökningar, även protoyptillverkning och produktanalyser.En del vikt har lagts på att genomföra marknadsundersökningar för att se om detfinns ett intresse för produkten..

This thesis work is about how technical consulting companies can accept their organization before a coming recession. Technical consulting companies are together with the rest of the actors in the construction business constantly depended on the current economic situation on the market. How to adapt the organisation depends on the current situation on the market.To adapt the organization in the best way possible the companies need to recruit and educate personal. It is then very important to find a solution on how the current change of generation in the companies will be handled. The large and very much competent group of 40-talists will in a few years retire.

This thesis treats Building Information Modeling, BIM, in the production stage. Brieflydescribed BIM is virtual model of a building object where all information about theobject is gathered. All the involved operators in the construction project have access tothe model and can gather or share information about the project. There are several waysto apply BIM in the production stage. This thesis primarily deals with visualization of theobject, preparation and planning, the ability to take amounts from the model andcoordination and clash control.The basic issue was highlighted by Byggdialog AB.

Cement manufacture accounts for 3-5 percent of total global carbon emissions. There is a growing interest in reducing the environmental impact and conserve limited natural resources. In cement production, clinker productions consume 87.5 percent of the total energy consumed in the cement manufacture.Cementa has since many years, focused on reducing the environmental impact of cement production. The work has involved the entire production process from selection of alternative fuels to the development of cement with less clinker content. During 2013/2014, two new types of cement (Bascement and CEM II / B) will be introduced to the Swedish market.

The Mission at ÅF Industry in Norrkoping was about optimizing bulk data handling while importing process tag types from their construction database into the Process Controlled System of type Siemens PCS7.I found three different methods to solve the task. Two of them were using different software from Siemens under the premise that the report from the database was corrected as needed. The third variant was manually creating the circuits. All methods worked out fine but there were times when one was better than another.To solve this task I had access to all software presented in chapter 2 ?Programvara? (=Software).

Arvika Smide is a supplier to the automotive industry with a focus on advanced drop forgings including powertrain and bearings. The great experience and high quality is Arvika Smide?s speciality. Today's competition in the industries puts high demands on the efficiency where each company has a quest for perfection.Arvika Smide has been through the thesis of Karlstad University, called for a situation analysis of aftertreatment whose effectiveness has not been fully desirable. The department includes the production steps blasting, quality control and packaging.The thesis contains the results from the situation analysis and comparisons of the calculations for selected reference period Q4 2009th.

System Andersson AB is a company located in Jönköping that works with developing computer systems for the mechanical engineering industry. As of today, when this report is written, the company is working on the development of a new Manufacturing Planning and Control (MPC) system. This new system aims to create not only a user friendly interface but also a modern, stylish interface. To achieve this, the company has decided to work with a, for them, new application framework; Windows Presentation Foundation (WPF).System Andersson is well known for developing systems for different kinds of touch screens, this project is no exception. For this new user interface the company wishes to implement different types of Drag&Drop functionality.

For a long period of time there have been discussions about the need to modernize, to keep up with the changes in our society. The schools as a result have to keep up and adapt in order for the education to be up-to-date. This includes the technological developments. Many steps have been taken and mighty sums have been invested in order to keep up the pace ? but are there any consequences from these kinds of investments? In this report I?m going to take a closer look on a recent addition to this phenomenon that were installed by means of a top-down approach and study the teachers and how they have adapted and view the change in their environment ? namely the newly installed interactive writing-boards.The questions I will study include how the teachers express their view about the installation of the interactive writing-boards.

En vanligt förekommande laminering är polyuretanskum, som används för att ge egenskaper som mjukhet, komfort och flexibilitet till textiler. Ett användningsområde som tillverkaren och leverantören Borgstena Group Sweden AB använder polyuretan till är lastbilars väggpaneler. De vill dock ersätta den polyuretanskumlaminerade dubbeljerseytrikån som används idag med endast en ren trikåkonstruktion för att slippa problem som dellaminering och minskade töjegenskaper. Dessutom så har den kemiska sammansättningen av polyuretan som används i lamineringen visat sig vara belastande för både miljö och människor. I denna rapport klargörs varför polyuretanskum behöver ersättas och vilka möjligheter som finns i dagsläget för att göra detta.

In this essay I want to investigate how the Viking aristocratic warrior elite in Scandinavia used religious mythology for the construction of their identity. The essay also takes up the concept of honor, which was important for the warriors. Honor was central to all people during Viking age and for the warriors it was absolute. In the religious myths, the aristocratic warriors justify their position in society and legitimate their acts of war. Religion continues to have importance to the warrior elite even after the arrival of Christianity.

This report shows the process of the development of a sensor module for the seed drills of Väderstad Verken AB. The module is supposed to replace existing solutions, provided that it is better from both a constructional- and an economical aspect. The purpose of the sensor is to continuously give the driver information about the level of height of the front- and drilling tools and the main purpose of the sensor is to allow the seeds to be placed at the desired depth. The sensors which have been taken into consideration have all been of an analogue type and have a protection class of minimum IP67.The methods applied have been taken from the book ?The Mechanical Design Process? by David G.