A home for elderly is planed to be built at Zakrisdal, Karlstad, Sweden. The heat source for the building was at the time not determined. In order by the local government of Karlstad this report is meant to examine if the need of heat could be provided only by solar heat combined with a seasonal heat storage. The problem to solve is, if the need of heat from the home for elderly is provided from only solar heat, whitch dimensions of the solar collectors and the storage is needed?.

Platelets are small fragments, but they are of crucial importance for the coagulation. The risk of spontaneous bleeding increases when the level of platelets falls below a thrombocyte particle concentration threshold value of 50 x 109/L. In those cases a platelet transfusion might be compulsory. Ongoing research tries to improve the quality of the platelets and to increase the safety of the method used. However, we still need to better understand which factors that affect how patients react upon platelet transfusion.

The acoustics in a control room is a complicated phenomenon. Early reflections, reverberation time and area in the room are some of the problems. This report is about the reflection on the mixing console in a control room. The control room being built, these reflections are difficult to take into consideration since the mixing console is one of the very last items you place in the room. This report will explain three main measurements that were done in order to get the answer to the following question: Does the mixing console interfere the frequency curve at listening position? Three measurements were done and the difference between the measurements was that the microphone and the loudspeakers were placed in different places in the control room.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Dagens moderna organisationer driver vanligtvis en kostsam IT-baserad infrastruktur. De besitter högpresterande funktionalitet och säkerhet för att garantera att de dagliga operationerna fortskrider. Mjukvarubaserade lagringsplattformar är ett alternativ som kan användas för att reducera dessa kostnader. Genom att efterlikna avancerad teknik som redan existerar i traditionella lagringsplattformar kan detta implementeras som mjukvara på commodity hardware i syfte att uppnå samma funktionalitet. Ceph är ett alternativ som numera implementeras och ämnar erbjuda detta val.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

A system for sampling of alcohol and aldehyde from diluted exhaust gases from vehicles powered by ethanol has been developed and tested. The major part of the work has been research of earlier work in the field and the construction of the sampling system.The part of the system constructed for the measurement of alcohol has been shown to work, however, more test should be performed. The part of the system constructed for the measurement of aldehyde was tested parallel to a commercially available system, based on the same principle of measurement, and has been shown to work well.Determination of the concentration of gaseous ethanol using a FID has shown the since earlier known fact that a FID is not able to measure a correct concentration of ethanol. Furthermore it has been shown that high concentrations of gaseous ethanol can not be kept in a bag more than a few minutes without a substantial decrease of the measured concentration..

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

The aim is to describe the factors that influence nurses' assessment and measurement of pain in patients. Literature study based on 13 reviewed articles, searched in the Cinahl. Qualitative and quantitative articles were analyzed. Six themes were identified that can be seen as the factors that influence nurses' assessment and measurement. The themes were   pain education, nurses´ experience in the profession, nurses´ level of knowledge about pain relief, documentation about pain, nurse´s perspective on the patient, and pain measurement.

Purpose: This study deals with warehouse management with an emphasis on vertical lift modules (VLM). The aim is to examine the effect of the implementation of VLM on a business's warehouse management. In order to obtain a result, the study has been based on the following questions:? How was the warehouse management designed before the implementation of VLM?? How is warehouse management designed after the implementation of VLM?Method: To be able to answer these questions, interviews with ten users of VLM performed. All users usually lift systems from the same manufacturer.

The sun is a huge energy source with great potential of providing energy to the heating of homes and other buildings in an environmentally sustainable manner. In order to provide buildings with energy from the sun it is necessary to transfer the energy supply over time to when the demand arises. By storing the heat in a seasonal storage, solar energy from the summer can be used in the winter when the demand for heating is greatest.Today's existing plants are mainly in Europe and particularly in Germany. These facilities are designed to supply heat demands greater than 400 MWh and covers about 40-50 % of this need which consists of energy for space heating and domestic hot water. How much of the heat demand that is covered, the solar fraction, is partly due to losses from the storage which in turn is connected to the surface area of the storage.

This thesis describes a method of measuring axial magnetic leakage flux in an operational hydropower generator. Axial magnetic leakage flux is the magnetic flux at the ends of a rotating generator, which goes through the stator parallel to the rotor axis. This flux can cause circulating currents in the stator iron, giving rise to losses, and can in the worst case overheat a generator, causing it to melt down. To measure the axial flux, and how it affects the generator temperature, a measurement system was constructed on behalf of Vattenfall. The system consists of search coil sensors and a signal-processing unit with amplifiers and active filtering.  To confirm the behaviour of the axial leakage flux and the functionality of the measurement system, a test installation was made.

Geothermal energy can be extracted from an aquifer, where the groundwater is used as heatexchange medium while heat and cold are stored in the surrounding material in the aquiferand to some extent in the groundwater. Application of aquifer storage for the use ofgeothermal energy is mainly used in large scale facilities and is limited to sites with suitableaquifers in the form of ridges, sandstone and limestone aquifers.Löwenströmska hospital in the municipality of Upplands Väsby, north of Stockholm, islocated nearby the northern part of the Stockholm esker. This means that it can be profitableand environmentally beneficial for the hospital to examine the possibilities of aquifer storagein the esker material next to its property.The purpose of this master thesis has been to investigate if geothermal energy storage with aseasonal storage of heat and cold can be applied within Löwenströmska hospital?s propertyarea using groundwater modeling. A hydraulic groundwater model was constructed inMODFLOW based on a simplified conceptual model of the groundwater system.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.