This thesis deals with different methods for measuring moisture-related dimensional changes ofwood. Typically relative humidity is measured to determine if the ambient climate around anobject is harmful to it or not. Values between 40 to 65% RH are recommended for hygroscopicmaterials. To know how a wooden object actually reacts to changes in the surroundingenvironment requires methods that involve the object itself. Because of the wood anisotropy,differences in wood structure, finishes and other restraints, it is not always possible to predict themovements.This paper addresses various measurement methods, primarily methods that have been testedin the field of conservation, with examples of their use.

The aim is to describe the factors that influence nurses' assessment and measurement of pain in patients. Literature study based on 13 reviewed articles, searched in the Cinahl. Qualitative and quantitative articles were analyzed. Six themes were identified that can be seen as the factors that influence nurses' assessment and measurement. The themes were   pain education, nurses´ experience in the profession, nurses´ level of knowledge about pain relief, documentation about pain, nurse´s perspective on the patient, and pain measurement.

The acoustics in a control room is a complicated phenomenon. Early reflections, reverberation time and area in the room are some of the problems. This report is about the reflection on the mixing console in a control room. The control room being built, these reflections are difficult to take into consideration since the mixing console is one of the very last items you place in the room. This report will explain three main measurements that were done in order to get the answer to the following question: Does the mixing console interfere the frequency curve at listening position? Three measurements were done and the difference between the measurements was that the microphone and the loudspeakers were placed in different places in the control room.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

A system for sampling of alcohol and aldehyde from diluted exhaust gases from vehicles powered by ethanol has been developed and tested. The major part of the work has been research of earlier work in the field and the construction of the sampling system.The part of the system constructed for the measurement of alcohol has been shown to work, however, more test should be performed. The part of the system constructed for the measurement of aldehyde was tested parallel to a commercially available system, based on the same principle of measurement, and has been shown to work well.Determination of the concentration of gaseous ethanol using a FID has shown the since earlier known fact that a FID is not able to measure a correct concentration of ethanol. Furthermore it has been shown that high concentrations of gaseous ethanol can not be kept in a bag more than a few minutes without a substantial decrease of the measured concentration..

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

The aim is to describe the factors that influence nurses' assessment and measurement of pain in patients. Literature study based on 13 reviewed articles, searched in the Cinahl. Qualitative and quantitative articles were analyzed. Six themes were identified that can be seen as the factors that influence nurses' assessment and measurement. The themes were   pain education, nurses´ experience in the profession, nurses´ level of knowledge about pain relief, documentation about pain, nurse´s perspective on the patient, and pain measurement.

This thesis describes a method of measuring axial magnetic leakage flux in an operational hydropower generator. Axial magnetic leakage flux is the magnetic flux at the ends of a rotating generator, which goes through the stator parallel to the rotor axis. This flux can cause circulating currents in the stator iron, giving rise to losses, and can in the worst case overheat a generator, causing it to melt down. To measure the axial flux, and how it affects the generator temperature, a measurement system was constructed on behalf of Vattenfall. The system consists of search coil sensors and a signal-processing unit with amplifiers and active filtering.  To confirm the behaviour of the axial leakage flux and the functionality of the measurement system, a test installation was made.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Blekinge Hospital suffers from a budget shortage of 100 million SEK, while the government now requires that hospitals will no longer be running a deficit. Blekinge Hospital will then use their limited resources to survive in the future and the activity must be enhanced in order to keep costs low without having to lay off personnel. The idea is that the organisation should be more efficient with a more efficient resource usage. Performance measurement systems are important tools for achieving the policies set out within an organization, measuring and evaluating performance is a way to see where improvements in efficiency may be necessary in the business. Balanced Scorecard (BSC) is one of several measuring systems, where the focus is on measuring non-financial performances.

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution.

This study was performed in collaboration with Moelven Skog AB, Örebro district. The purpose of the study was to review existing literature in order to describe the current status of harvester based measurement technology as the way to provide information for calculating payment to the forest owners. In addition to this, a short survey was conducted to find out how a switch to harvester based measurement would affect the administrative workload on timber purchasers working for the district. The literature study shows that the harvester measurement technology is ready to use if it is combined with well-established routines for control of the harvesters, methods for automatic quality indexing of the timber and ways of creating pricelists specially adapted for harvester measurement. Pricing each stem seems to be the most promising method. Stem pricing has several benefits.

För att uppfylla kraven på kvalitetssäkring samt evidensbaserad praktik måste hörapparatanpassning utvärderas objektivt. Syftet med studien är att redovisa nya forskningsresultat gällande objektiv utvärdering av hörapparater med hjälp av hörselgångsmätning, samt att beskriva en modern, evidensbaserad och kliniskt användbar metod för de vanligaste typerna av elektro-akustiska hörapparater med olika typer av insats. Studien består av en allmän litteraturstudie som beskriver tidigare rekommendationer samt en systematisk litteraturstudie där nya rön gällande metodiken vid hörselgångsmätning presenteras. Utifrån hörselgångsmätningens olika delmoment undersöker studien vilka konsekvenser de nya rönen har för utförandet vid hörselgångsmätning. I slutsatsen presenteras en metod för objektiv utvärdering av moderna hörapparater..