This report contains a degree project made by the mechanical engineering students Lennart Andersson and Daniel Jansson. The project has performed in assignment by SOMAS Valves AB in Säffle. SOMAS are leading in development on control and on/off valves. To maintain this position they always want to improve their products. One way in this development is valves that are more tightened.The purpose with our project was to investigate another seat design on a HiCo (High Cobalt Alloy) seat to a SKV 150 PN 25 valve and compare this to an original HiCo seat.By modifying the seat on a ball valve we want to achieve a valve that leaks lesser then a valve whit original seat.

Product development is a risky business; many products never yield profit, but it is also ne-cessary for a company?s survival in a competitive business where the costumers change their requests constantly. Consumer-led product development is developed from the wish to fill the consumer?s needs and expectations and thereby be more likely to succeed. Lindell?s Gårdsslakteri AB is a local slaughter and meat processor in Västergötland.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual Manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual Manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from Manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the Manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

Powder Metal (PM) gears are machine element components which operate under the same principle as conventional gears, but, due to their intrinsic material characteristic need to be designed slightly different, and its Manufacturing process offers advantages previously unobtainable by conventional steel gear Manufacturing methods. The use of PM in similar applications, such as synchronous hubs, makes them a suitable candidate for production in such material. The current master thesis work focuses on gear design using PM by utilizing finite element method (FEM) to reduce weight and inertia taking into account root bending strength and tooth deflection.First a topological optimization is used to determine feasible candidates for different web designs which have as objective to reduce volume, similar topologies were shown during different loading conditions; and hence, this topology was chosen as a suitable candidate. A shape optimization of the topological candidate was performed having as state variables root bending strength, independent for compressive and tensile side of the tooth loading; and tooth deflection, which in concept can be correlated to static transmission error (TE).Another aspect in this thesis analysed is the possibility to incorporate non-trochoid root geometry, a trochoid root is always present when machining with a hob, into the gear root and hence reduce the stress concentration here. Due to the use of PM, a non-symmetric optimized root can be achieved and hence be optimizing compression and tension.Results showed significantly lower inertia, for example certain results showed 40% reduced when compared to solid gear, with adverse effects as increase in tooth deformation and increase in maximum principal stress.

ÅF Test Center in Borlänge had a need to expand their capacity for compressive and tensile strength tests. They wanted to do this by using a hydraulic cylinder, which they already possessed, to apply the force with. This required a load receiving structure. The aim of this work was to design and dimensioning a test bench for a cylinder marked NIKE 300 tons. The work would result in a completed design proposal on a test bench which could manage to run the compressive and tensile strength tests of up to 3000 kN.

Oxelösund är en liten kommun på den Södermanländska kusten. Denna kommun har trots sin storlek stora problem med ohälsa i form av bland annat hög andel missbrukare. Dock kan man se att hälsoproblemen i Oxelösund är mer omfattade och innefattar i princip alla områden av folkhälsan. Man kan se att riskfaktorerna delvis är fler än friskfaktorerna. Detta kan vara en del i samhällets habitus, man en ohälsosam livsstil i Oxelösund..

The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from Manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the Manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

In conventional viscose Manufacturing, a large amount of carbondisulfide is consumed. This amount has to be decreased to keep the production cost down and to reduce the environmental impact. The purpose with this work was to show if an enzyme treatment of a dissolving pulp could increase the degree of substitution in the viscose so that the amount of carbon disulfide consumed in the process could be decreased. Previous investigations by Kvarnlöf (2007), Engström et.al. (2006) and Henriksson et.al.

Most people have been forced to throw away a pot-plant after its death. There are many reasons to the death of a plant, but mainly it?s because its owner forgets it, and therefore fails to water it. The purpose of this project is therefore to develop a product which can prevent this from happening, while the product has to have a low Manufacturing cost to be able to compete whit other, similar, products on the market. During the project, a benchmarking has been done to give a clear picture of what the product has to compete with. The directives there are for CE-marking, and which of these who concerns the product has also been looked up.

This report will discuss principle, primary and finally Manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally Manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally Manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally Manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.