Dimensional stability is an important aspect of fuel mechanical design and licensing of new fuel designs for nuclear power plants. Dimensional changes within the reactor can affect the safety margins against overheating of the cladding and the pellets, therefore it is crucial that the dimensional changes are kept to a minimum.The profits per produced kiloWatt hour continue to decrease for the Swedish nuclear power plants. Some reactors are even operated with a calculated loss. To reduce fuel costs and thereby improve the profit some reactors are operated with higher uranium enrichment, so that the assemblies can reach a higher average burnup. This increases the neutron fluence to the pellets, cladding an spacers.

The purpose of this Bachelor degree project is to design different types of services that can increase the amount of re-used timber within the building sector and by that means improve their environmental efforts. By examining how the sectors environmental work concerning recycling and re-using timber as a building material is getting on at present, conclusions have been drawn about what further could be done for improvement.The project has shown that there is a scarcity of information and statistics within the sector, but that there are efforts in progress to change this. Questionnaires have been sent to a number of companies working with demolition and utilizing re-usable materials in order to find out what kind of problems there are within the trade. Unfortunately the survey gave insufficient result due to the low reply frequency.It is obvious that active environmental work within the building sector is important and the knowledge acquired while working with the project has led to the design of three suggestions for services regarded as being of interest for improving the negative environmental impact caused by the sector:Suggestion 1 ? Sale of construction parts prior to the demolition of a buildingSuggestion 2 ? Re-utilization circulation when manufacturing buildingsSuggestion 3 ? Education in relation to the purchase of houses  The positive and negative qualities of the suggestions have been examined with SWOT-analysis and further adaptions and the results have been interpreted.

ProblemThe manufacturing industry is a mature industry where the profit margins are small and the competition is hard. This makes it hard for both manufacturers and resellers to gain market shares and reach reasonable profit margins only by selling products. Therefore Swecon who is reseller for Volvo Construction Equipment tries to find alternative methods and ways to increase their profit. An alternative source of income could be to develop the range of services that are connected to the ground products.PurposeThe purpose of the thesis is to examine how Swecon in southern Sweden can improve their offers of existing services connected to the ground product and investigate the demand of new such services.MethodThis study is based on a qualitative study of five of Swecons local offices and five of Swecons customers. The empirical framework is mostly based on personal interviews but in some cases information was retrieved by using phone interviews.

Möjligheternas värld är en utställning som ska presenteras på olika mässor. Hjärtat i utställningen är automationsfabriken som är en automatiserad anläggning som ska tillverka leksaksbilar. Automationsfabriken ska invigas på mässan Scanautomatic och ProcessTeknikden 9-11 oktober 2012. Då möjligheternas värld är ett samarbete mellan näringsliv och skola bidrar företag och skolor med hjälp och samarbetar för att projektet ska bli lyckat. Prevas del i projektet är att ta fram ett styrsystem i form av ett MES och SCADA system till fabriken samtatt göra hemsidan där bilar kan beställas och integrera den med styrsystemet.Målet med examensarbetet är att utveckla styrsystemet och ta fram ett HMI genom att använda programvaror från Wonderware.

The aim of this master?s thesis is to examine which ideas about the public library that appear in a selection of municipal library plans and to examine if these ideas are unanimous. The comprehensive questions are: Which ideas about the public library appear in each municipal library plan? How do the ideas agree in the different municipal library plans? The sub questions are: Which judgements of reality appear in the different library plans concerning each municipality and its library needs? How do the municipalities define the concept of development and future demands in the municipality on the basis of the judgements of reality? Which recommendations do the judgements of reality give and how is the plan of action that is established in each library plan justified? Which fundamental views of reality, i. e.

Atlas Copco Tools is a world leading company in tool manufacturing. The productionin Tierp works hard to improve their assembly to maintain its position. This thesis isa part of their improvement efforts to be a more Lean production.The main focus for this thesis was to identify the material flow in the kanban system,which used to supply the assembly groups, focusing on the material flow to assemblygroup 9 and the assembly group 3. Group 3's material flow within the kanban systemwas perceived to perform better than the group 9. The handling of kanban materialand their working methods in the two groups was identify those differences whichaffected the kanban system.As an alternative material supply a study were done in kiting.

The intention with this study is to investigate how schools are affected by state and municipal documents when they organize the education for children with special needs. The study is based on following questions.How do decisions on state and municipal level of politics affect the decisions that the principals make concerning organization, and do the school leaders think that the decisions are made on the right level of liability?What is the relationship between economic decisions and pedagogical decisions?What decides whether the schools have children with special needs integrated in their ordinary classes, or if they receive segregated remedial courses, and what are the views on an equivalent education?The study is conducted through interviews with principals of three schools, one politician on municipal level and one special education teacher. The interviews are linked to an historic background as well as current studies and discourses. The study shows that there are contradictions between state, municipality and school goals.

Construction companies in Sweden have for recent years seen an increase in the numbers ofwarranty complaints associated with the market of resident buildings and the cost for this hasbeen measured to over 1.2 billion SEK per year. Working with poor quality cost as a way ofcreating insight about defects within the company?s processes is a method developed and usedby the manufacturing industry for decades, but have not yet reached the construction industry.This study has been performed in collaboration with a Swedish construction company, wherethe author has been stationed at the aftersales division for residential buildings. Owing tocircumstances, this published report has been made anonymous regarding the company whowill further on be namedthe Company. The Company is aware that warranty claims producegreat costs and has requested a way of putting cost and cause to specific claims in order ofreceiving a more specific cost view and to make the reuse of knowledge more efficient.

AbstractThis master thesis was performed at Scania transmission department in Södertälje, where the manufacturing of gears is done. Today a large amount of manual handling is performed between the machining and the hardening process. Most of the manual handling is done at the heat treatment department. The purpose of this master thesis is to give a suggestion on how to reduce or eliminate the manual handling at the heat treatment department. The possibility to use the same packaging throughout the processes will also be investigated.

SAAB Automobile ABis a car manufacturer within General Motors corporate group. SAABAutomobile ABhas a big part of the responsibility for the brake development in the corporategroup. The car industry is facing harder environmental requirements, which influence the brakedevelopment. The focus is to develop brakes with low drag and sustained brake feeling andperformance. Important characters for the brake caliper are high stiffness and low weight, highstiffness results in high performance and low weight is important because it is unsprung mass.This thesis investigates the possibility to improve the performance of the brake caliper for aGMproject.

Demand has become increasingly difficult to forecast in today?s volatile markets. Being able to produce towards real demand is becoming vital for companies, since inventories of finished goods are expensive to maintain and because miscalculated products tie up capital that in the end is never repaid. More and more companies are using postponement strategies to delay the process of producing until real demand has become known. Tooling Support Halmstad is a company within the manufacturing industry, which has become aware of the benefits with postponement strategies for parts of their production.

The process of food production has changed dramatically over the past one hundred years. Industrialization has led to large units of production, manufacturing, distribution, marketing and retail business. The final food product, in this system, is quite often fairly anonymous and the consumer will most likely know very little concerning the origin of the product. In recent years, the market for locally produced food has grown. There is an increasing interest in and demand for locally produced food items.

Construction companies in Sweden have for recent years seen an increase in the numbers ofwarranty complaints associated with the market of resident buildings and the cost for this hasbeen measured to over 1.2 billion SEK per year. Working with poor quality cost as a way ofcreating insight about defects within the company?s processes is a method developed and usedby the manufacturing industry for decades, but have not yet reached the construction industry.This study has been performed in collaboration with a Swedish construction company, wherethe author has been stationed at the aftersales division for residential buildings. Owing tocircumstances, this published report has been made anonymous regarding the company whowill further on be namedthe Company. The Company is aware that warranty claims producegreat costs and has requested a way of putting cost and cause to specific claims in order ofreceiving a more specific cost view and to make the reuse of knowledge more efficient.

During the past twenty years, the Swedish school systems have slowly changed to becomemore and more performance-driven. Private schools have been growing in general and, likeindependent schools and schools managed by municipalities, they profile themselves. Schoolsare becoming more performance and result-oriented, which has changed the roles of teachersin a dramatic way and is in general, still changing.By profiling students based on theirindividual performance, schools are able to help students identify themselves and their owngoals. The process of profiling is a slow one in which some teachers adapt more quickly thanothers, and one that is critical for other teachers to learn in order to keep up with the demandsof society.Schools, like ordinary businesses, are in constant competition with each other to keep up withthe newest and greatest models of teaching and to rank among the best in high achievements.Perhaps the downside of this modern school structure is that it is often difficult to have aschool where both school management and teachers see eye to eye. School management must heavily focus on the school?s results as a whole.

During spring 2009 a three meter tall and laughing robot was developed in collaboration between Royal Institute of Technology and Royal University College of Fine Arts. The robots function and esthetics is based on an existing toy robot called Elmo. Elmo is 30 cm tall but now the goal was to make it 1000 times bigger in order to present it on the spring exhibition of Royal University College of Fine Arts. Due to only four months of developing and building time a demand of fast determination and good planning was required. In order to make a good structure for the project it is divided into five phases: Analysis of Elmo, planning, concept development, detail construction and finally product development and testing.In the first phase valuable knowledge is obtained according to the movements and geometry of Elmo.