The thesis presented in this report has been made on behalf of Scania and their basic frame design department with the subject to solve an implementation of a weight sensing system in the chassis. The system is supposed to be implemented in the seat springs, and the reason for this is that all the force will have to go through the weight sensing transducers. With all the force going through the transducers the weight sensing system will not be sensitive for the differences in tolerances from manufacturing. The transducers could be pre-calibrated to avoid a calibration of the whole vehicle after it?s completed from the manufacturing line.Weight sensing systems is today a reality in trucks with air springs.

In conventional viscose manufacturing, a large amount of carbondisulfide is consumed. This amount has to be decreased to keep the production cost down and to reduce the environmental impact. The purpose with this work was to show if an enzyme treatment of a dissolving pulp could increase the degree of substitution in the viscose so that the amount of carbon disulfide consumed in the process could be decreased. Previous investigations by Kvarnlöf (2007), Engström et.al. (2006) and Henriksson et.al.

Most people have been forced to throw away a pot-plant after its death. There are many reasons to the death of a plant, but mainly it?s because its owner forgets it, and therefore fails to water it. The purpose of this project is therefore to develop a product which can prevent this from happening, while the product has to have a low manufacturing cost to be able to compete whit other, similar, products on the market. During the project, a benchmarking has been done to give a clear picture of what the product has to compete with. The directives there are for CE-marking, and which of these who concerns the product has also been looked up.

 AbstractAttractiveness may be defined by a variety of factors but you should see it in the public planning as it is to have a positive population growth and economic growth, through working with communications, service, housing, to name a few. This is done primarily through direct projects both within the municipality and through various partnerships between local and regional level. The progress we have seen in recent years has gone more towards a clear shell level, particularly a regional level where these have had a much greater freedom with clear geographical boundaries in between each other. Within these regions there are also clear regional groupings that have common interests and competing between each other. In my thesis, we have been distinguished including three levels of scale levels.

Assisted living is a relatively new form of housing that received a government definition in 2007 in conjunction with a government appointed investigation of future alternative accommodation for senior citizens. The type of accommodation is intended for seniors who have the need for increased security, which may be a consequence of that they feel anxious or lonely. It concerns ordinary homes with qualities that suit needs of seniors. There is no allowance from the local municipality required in order for seniors to apply for these homes and so assisted living should not be confused with nursing homes/ sheltered housing. The purpose of this study is to identify success factors for a winning concept for assisted living in the Gothenburg region, on behalf of Skanska Project development.

The city?s public environments are meant to be perceived as safe and inviting areas to visit any time of the day. In recent decades the number of vandalism complaints has doubled and graffiti has become so common that it received a separate category in the crime statistics. With this type of impacts in the public environments the experience are precarious and a boring sight. It?s difficult to put a price tag on these types of crimes, the number of unreported cases suspected to be large.

Lokala investeringsprogram was a subsidy program which supported environmental reforms during the years 1998 to 2002. The subsidies were given to Swedish municipalities. Most of the evaluations of the subsidised projects have now been completed and included in a database. The purpose with this thesis is to analyse whether the instrument has been effective with respect to carbon dioxide reductions and costs. These calculations have focused on subsidy and cost efficiency. The analysis has been compared with a previous report called "LIP ur ett samhällsekonomiskt perspektiv". The result shows that the reduction cost for one kg CO2 has been almost one SEK, which is twice as high as the cost reported in a previous report, half a SEK.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

The city?s public environments are meant to be perceived as safe and inviting areas to visit any time of the day. In recent decades the number of vandalism complaints has doubled and graffiti has become so common that it received a separate category in the crime statistics. With this type of impacts in the public environments the experience are precarious and a boring sight. It?s difficult to put a price tag on these types of crimes, the number of unreported cases suspected to be large.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

The automotive industry is increasingly studying lightweight solution in their designs, also rational production and low costs in materials and manufacturing methods are of great interest. This thesis consisted in the practical evaluation of anchors for sandwich panels. The object was to study loads of shearing and pull out of the plane. The experiments were carried out on panels made up of 1mm aluminium coatings and 50mm extruded polystyrene (XPS) at its core. As the fasteners used simple methods such as blind rivets, screw and glue.

Detta examensarbete omfattar produktutvecklingen av en komponent till en mätutrustning som ska mäta flytbarheten hos smält metall. Arbetet har utförts hos Bryne AB och har lett fram till koncept-, material- och tillverkningsförslag för komponenten. Arbetet har även utvärderat ett för gjuteribranschen nytt formmaterial som alternativ till dagens gjutsand. Tester har gjorts för att se om återvunnet (material x) går att använda som formmaterial till högtemperaturapplikationer..