This thesis is divided into two parts. Part one contains a general description of the flexographic printingtechnique. Part two contains a more detailed investigation in the areas substrate, inktransfer and trends, which are only briefly commented in part one, and conclusions and comments.The major problem concerning substrate is washboard. This phenomena can be limited if one can control and minimize the amount of glue applied in the single- and double facer, use high surface weight on liner, use low surfaceweight on fluting and control the humidity during the conditioning of the corrugated board. Corrugated board with a smooth surface radically increases the quality in print.

This thesis is divided into two parts. Part one contains a general description of the flexographic printingtechnique. Part two contains a more detailed investigation in the areas substrate, inktransfer and trends, which are only briefly commented in part one, and conclusions and comments.The major problem concerning substrate is washboard. This phenomena can be limited if one can control and minimize the amount of glue applied in the single- and double facer, use high surface weight on liner, use low surfaceweight on fluting and control the humidity during the conditioning of the corrugated board. Corrugated board with a smooth surface radically increases the quality in print.

Wetlands are important ecosystems and form habitat for both common and threatened species. In Sweden, as well in many other places on earth, there is a lack of wetlands. There is an expressed will to adjust this lack through restoration of wetlands with reduced function and through construction of new wetlands. Follow-ups and evaluations are important steps to optimize these actions. The wetland Vattenparken was constructed 1999 ? 2000 for treatment of surface water.

Forestry has three main aspects to take into consideration today; economical, ecological and socio-cultural. In order to reach the broad policy goals for sustainable forest management, an increased variety of management approaches are requested. Today clear-cutting is the only method used in 96 % of the managed forests in Sweden. The Swedish National Board of Forestry has therefore initiated a project in order to investigate and develop Continuous Cover Forestry (CFF). This study is a part of this project.

This thesis is divided into two parts. Part one contains a general description of the flexographic printingtechnique. Part two contains a more detailed investigation in the areas substrate, inktransfer and trends, which are only briefly commented in part one, and conclusions and comments.The major problem concerning substrate is washboard. This phenomena can be limited if one can control and minimize the amount of glue applied in the single- and double facer, use high surface weight on liner, use low surfaceweight on fluting and control the humidity during the conditioning of the corrugated board. Corrugated board with a smooth surface radically increases the quality in print.

The project was initiated by Medipharm which produce microbial inoculants which used as additives to preserve forage. The main goal was to test three inoculants to produce maize silege. The following Medipharm produced inoculants were tested, Milab 393, Lactisil Wolecrop II, Lactisil 300 2. An untreated control was included in the study. The trial was done at Swedish university of Agriculture and Science in Alnarp, Sweden. Eurostar was the cultivar of the maize and was grown on 20, 5 hectares.

This thesis is divided into two parts. Part one contains a general description of the flexographic printingtechnique. Part two contains a more detailed investigation in the areas substrate, inktransfer and trends, which are only briefly commented in part one, and conclusions and comments.The major problem concerning substrate is washboard. This phenomena can be limited if one can control and minimize the amount of glue applied in the single- and double facer, use high surface weight on liner, use low surfaceweight on fluting and control the humidity during the conditioning of the corrugated board. Corrugated board with a smooth surface radically increases the quality in print.

This thesis deals with the numerical 3D simulation of a four stroke, spark-ignited, internalcombustion engine, which is mounted on a high performance motorcycle. The work, carried outin collaboration with Politecnico di Milano and MV Agusta, focuses on the simulation of theintake, compression and expansion stroke, including combustion simulation, using an opensource CFD code.Simulation of internal combustion engines offers a great challenge in the field of CFD research.Moving boundaries of the solution domain, caused by the motion of the piston and valves, leadsto deformation of the computational grid, with decreasing quality of the solution as result. Basedon this, a previously developed mesh motion strategy was employed where a number of meshesare used to cover the whole simulation cycle. Within each mesh interval the internal cell pointsof the mesh are moved to account for the boundary motion of the piston and valves. This strategywas previously applied to simplified geometries as well as real engine geometries.

This thesis is divided into two parts. Part one contains a general description of the flexographic printingtechnique. Part two contains a more detailed investigation in the areas substrate, inktransfer and trends, which are only briefly commented in part one, and conclusions and comments.The major problem concerning substrate is washboard. This phenomena can be limited if one can control and minimize the amount of glue applied in the single- and double facer, use high surface weight on liner, use low surfaceweight on fluting and control the humidity during the conditioning of the corrugated board. Corrugated board with a smooth surface radically increases the quality in print.

New rules for bank capital adequacy were introduced in 2013. This caused a changein funding of real estate companies. The bank could not cover as much of thecompanies funding?s as before and they had to explore other funding opportunities,such as bonds. Bond funding in Swedish real estate companies regularly consists ofunsecured corporate bonds and the secured ones are not that common.

BT is a global company within the lift truck industry. The main office is located in Mjölby. In Europe all sales and service activities are carried out by fully owned sales companies. I North America, BT RAYMOND develop and distribute trucks under a different brand. For the rest of the world BT works together with a distributor network, most of them are fully independent others BT has a small ownership in.

The real estate company Ihus is facing an expansion of its comfort cooling in Noatun,Uppsala, to provide the buildings in the block with cooling. The buildings in Noatunare mainly used for office premises, where the requirements for an accepted indoorclimate is great. However, it?s uncertain whether Ihus should continue, as currently,producing comfort cooling by themselves using a compressor chiller, or if they shouldconnect themselves to Vattenfall?s district cooling net.The purpose of this report is to examine which technique of cooling is best suited forIhus and their buildings in Noatun. It should also work as a guideline for othercompanies facing the same problem as Ihus.

The purpose with this thesis is to get a compilation of all the critical bolted joints of all enginesproduced at LV Motors. ABB LV Motors produces induction engines with seven shaft heights. Eachengine size exists several variants of components ex. standard shield and flange shield. Depending onwhich components the engine is equipped with arises various types of strains in the engine's parts,certain assembly ways are more favourable than other.The most critical parts in the engine from a mechanical point of view are the screw units betweenshield/stator, feet/stator and bearing cover/shield.

Vattenkraftstationer, med dammar och turbiner, utgör hinder för nedströmsvandrande smolt. Syftet med denna studie var att undersöka turbindödligheten för öringsmolt (Salmo trutta) vid två kraftstationer, de befintliga ytlänsarnas avledningseffekt och om effekten kunde förstärkas genom mörkläggning i form av övertäckning av kraftkanalen med en presenning vid turbinintaget. Utöver detta var avsikten även att undersöka om det fanns något samband mellan smoltgrad och smoltens förmåga att förflytta sig mot havet. I Emån i Småland fångades 46 öringsmolt som radiomärktes och sattes ut vid två kraftstationer och pejlades dagligen i sex veckor. Det var en större dödlighet vid den övre stationen än vid den nedre.

Den här uppsatsen undersöker Landstinget i Värmlands personaltidning Intryck och dess betydelse för organisationskulturen. Huvudsyftet med studien är att titta närmare på hur de fem olika yrkesgrupperna läkare, sjuksköterskor, undersköterskor, sjukgymnaster och dietister framställs i tidningen. Uppsatsen tittar också på hur personal inom yrkesgrupperna själva anser att de representeras i tidningen, samt om tidningens syfte når fram till personalen. Studien utgår från teorier om kommunikation, internkommunikation, organisationsteori och organisationskultur. Ett viktigt begrepp för uppsatsen är bland annat transmissionsmodellen som ger en grundläggande syn på hur kommunikation fungerar genom en personaltidning.      För att uppnå uppsatsens syfte har en fallstudie, genom två metoder, gjorts. Personaltidningen Intryck analyserades genom en kvalitativ innehållsanalys där tre frågor ställdes till texterna: Hur framställs yrkesrollerna i tidningen?, Fokuserar texterna på team eller individer? och Är kommunikationen tillgänglig för alla? Frågorna syftade till att få svar på uppsatsens övergripande frågeställning angående hur yrkesrollerna framställs.