HAFA Bathroom Group has given us the assignment to develop a standardized back panel for their bathroom cabinets. This cabinet is going to be applied to most of their current and future cabinet solutions. To this point, they have constructed unique suspensions-and back panels for most of their cabinet models. They have also been forced to pull wiring and assemble the cabinets differently because of factors like; position of the wall sockets, dimensions of the cabinets and their shapes.The company wants to distance themselves from their current solution, firstly because the cost of having manpower to design each individual suspension solution, secondly because they will save a lot of money when the manufacturing process requires a minimum of components to be constructed. As a result of this, the company can use their resources better to develop future products.The main idea is that the consumer isn?t required to change the suspension or back panel when they decide to buy a new cabinet.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

AbstractThe concept project is today used in several contexts and has different meaning in different contexts. Lately, projects have been seen as a form of organization and more companies convert from traditional organizing to organizing in a project form. The purpose and focus of today?s project is not only to increase quality and competence development for management but also to integrate different actors in order to e.g. increase customer value.LänsTeknikCentrum AB (LTC) in Jönköping is running different projects in order to support companies in Jönköping County.

 Title:Transshipment Terminal ? A study of environmental effects from the introduction of a transshipment terminal and a route planning system in the municipality of Kalmar Examiner:Andersson, PetraKey words:Transshipment terminal, route planning, environmental impact Purpose:The study aims to examine how a transshipment terminal and a route planning system may have implications for the municipality of Kalmar from environmental concerns. Methodology:The thesis is a case study on the municipality of Kalmar. A positivistic -and an objectivistic approach have been used. The strategic approach that was used was quantitative.

In Sweden regulations stipulates that dairy cows are kept on pasture, or given the opportunity to spend time outside during a coherent period of between two to four months, depending on region. The transition out to pasture is a big change from the winter period in the stable, especially for the modern high yielding dairy cows. The let out to pasture includes a change in feed, environment, and new routines. There are indications that the milk somatic cell count (SCC) rises in a peak shortly after the let out. The purpose of this study was to see if peaks in the SCC could be observed after the let out, and to study the contribution of inflammatory cells (neutrophils) and if the milk composition are affected. The study included 35 cows that were kept in stable during the winter.

Agriculture has to be performed in a sustainable way in order to sustain high yields and to support a globally growing population. Functional soil properties are fundamental for high yields and in order to achieve good soil conditions sustainable management is a key. Loss of soil organic material and increased soil acidity are problems associated with degradation of soils and hence less sustainable agriculture. In this thesis, the effect of different agricultural systems on soil organic matter, pH and yield was examined. The systems examined are a cereal system with straw removal or returning and a ley system, all with different nitrogen levels.

Syftet med undersökningen var att ge en bild av hur studenter i en högskoleutbildning på distans upplever sitt lärande. Fokus har lagts på den eventuella kopplingen mellan studenternas yrkeserfarenhet/yrkespraktik och deras lärande i en utbildning. Undersökningen utgår ifrån ett kvalitativt forskningsperspektiv och ett fenomenologiskt synsätt. Den empiriska undersökningen genomfördes i form av intervjuer med fem studenter som utbildar sig till lärare inom förskola och förskoleklass. Intervjuerna bearbetades och analyserades utifrån undersökningens syfte och frågeställningar och utmynnande i ett antal övergripande områden och teman.

Business plan competitions have long been used as a mean for entrepreneurial organizations and Universities to educate students in entrepreneurship. But what's in it for the entrepreneur This thesis aim is to understand what utility business plan competitions have for the participating entrepreneurs. It consists of interviews with Swedish entrepreneurs at various stages in the entrepreneurial process, who has participated in business plan competitions to get ahead. The conclusions of the study are that business plan competitions are good for the entrepreneur from a motivational and developmental perspective but not from a financial perspective..

Technology based self-service (TBSS) used in supermarket self-scanning checkouts is a relatively new phenomenon in Sweden. Studies on TBSS as a self- checkout device have been formerly carried out but with focus on the customer perspective. The authors therefore saw a challenge in covering the self-scan checkout concept, from a company perspective. The purpose of this research paper is to investigate, through a management perspective, the changes brought about by implementing an innovative TBSS system in Swedish supermarkets, and its effect on the competitiveness of the company. This is done by presenting and linking the theoretical framework and empirical study in the research.

This paper is written as an examination paper at the University of Jönköping. The subject is chosen by Peab Sweden in Jönköping with whom further cooperation has been hold. The aim is to compare building methods and building materials in Sweden, Finland and Germany for further inspiration for Peab?s own market.BackgroundThe development of the construction industry develops new materials and methods to the market which has been forced by shorter construction times and the environment aspect. To pursue the development, further knowledge exchange should exist between the countries.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

This report will discuss principle, primary and finally manufacturing structure. We were asked to produce a 3D milling to processing the prototype material that is used on the University of Halmstad. From conceptual drawings to produce components for this project have we together with a number of company take developed the right components for this project. We have calculated and analyzed the construction to get the best result for it purpose. Unfortunately have the process to produce the 3D milling has been stopped because of deficient budget and time.

AbstractPurpose ? The purpose of this study is to investigate possible reasons for long lead-time in a customer driven production, and how the lead-time can be reduced. To fulfil the purpose the study has been broken down into two questions.1. Whichfactorsaffectthelead-timeinacustomer-drivenproduction?2.