The district heating load is seasonally dependent, with a low load during periods of high ambient temperature. Thermal energy storage (TES) has the potential to shift heating loads from winter to summer, thus reducing cost and environmental impact of District Heat production. In this study, a concept of high temperature borehole thermal energy storage (HT-BTES) together with a pellet heating plant for temperature boost, is presented and evaluated by its technical limitations, its ability to supply heat, its function within the district heating system, as well as its environmental impact and economic viability in Gothenburg, Sweden, a city with access to high quantities of waste heat.The concept has proven potentially environmentally friendly and potentially profitable if its design is balanced to achieve a good enough supply temperature from the HT-BTES. The size of the heat storage, the distance between boreholes and low borehole thermal resistance are key parameters to achieve high temperature. Profitability increases if a location with lower temperature demand, as well as risk of future shortage of supply, can be met.

SAPA´s resource of waste heat is the basis for this thesis to investigate the possibility of energy assets in their cooling water and possible uses for it. The energy in the waste water is greater than the current need which has three uses which are (1) heating the factory, (2) converting liquid propane to propane gas and (3) local domestic heating. The average energy load that is available is 1, 7 MW and the average temperature in the cooling water is 41°C. The total energy load at dimensioning out side temperature is approximately 1,6 MW for the three current uses. The temperature is currently too low to be used directly in the existing systems so an upgrade is needed.

Arlanda airport is Sweden?s largest airport. The demand for comfort cooling of the airport?s buildings is high and is mainly provided by district cooling. District cooling is based on the same principle as district heating.

Introduction: Dolomite AB was in need of a dummy arm for crutch testing, to complement their existing test capabilities. Background: A large number of people need crutches on a daily basis. For them it is essential that their crutches do not fail. ISO (the International Organization for Standardization) conducts ongoing work to guarantee the durability and function of e.g. crutches.

The work covered in this report includes a literature study of the diesel dual fuel technology(hereinafter referred to as DDF). The literature study covers earlier work that has been doneregarding the use of compressed natural gas (CNG) and diesel in a DDF system. Moreover a onecylinder research diesel engine was fitted with a CNG fuel system for experimental testing. Theinstallation of the engine and the test cell is described. Results from the tests are presentedcovering emissions, heat release and pressure traces from the DDF-concept.During the literature study it was found that most research was related to heavy duty dieselengines.

In past decades information technology has changed the conditions of organizations, not at least within the industry. Advanced IT systems have become a fact in order to cope with rapid changes in the market and to effectively manage an organization?s knowledge. When organizations became more flexible and customized expectations from customers and stakeholders also become higher. These expectations and guidelines are documented in a company?s management system, which can be designed differently depending on what standards the company chooses to implement.

Concrete floors have traditionally had no problems with annoying vibrations. However with the demand for larger spans the floors need to be made more slender with a higher degree of utilization and lower mass. Therefore new floors may have problems with vibration serviceability. This thesis studies the vibration characteristics of hollow core slabs. The analysis was made in the finite element program Ansys. The hollow core slab was subjected to a varying force simulating one person walking across the slab.

This bachelor?s project deals with both the problems of high water temperatures in fishponds at a fish-breeding station and of the nutrient load to nearby lakes and streams in Harasjömåla, Blekinge, Sweden. Theory, methods and results of the analyses are presented in the report..

The purpose of this study was to examine how small-scale private forest ownersmake decisions regarding pre-commercial thinning. In 2015 it is ten years agosince the storm Gudrun hit the southern parts of Sweden and now large areas arein need of pre-commercial thinning. This study is built upon qualitativeinterviews with seven small-scale private forest owners with forest properties inthe county Kronoberg. The respondents were chosen by the modelSKOGSÄGARPROFILENTM (forest owner profile).The results of the interviews showed that five categories: ownership, the stormGudrun´s impact, silviculture, forestry contacts and driving force was important.How will their purpose and aim affect the pre-commercial thinning? Personalinterests, and expectations of the next generation to take over, are purposes thisstudy has found.

At the beginning of 2011, Sweden started using the European rules for structural design, the Eurocodes, instead of the previous national rules. In both the previous rules and the Eurocodes, it is possible to dimension concrete columns using tabled values. However, the required cross section measurements have increased considerably. Moreover, it is possible to dimension concrete columns using calculations, however, this is unusual.The development of a fire in a fire cell can be divided into the growth stage, the fully developed fire and the cooling phase. The duration of each phase, as well as the temperature, is dependent on a number of factors, e.g.

Abstract 1.The purpose of this study was to investigate the effects whole body vibrations on maximal strength, power output and neuromuscular activity in m. pectoralis major during bench press.Participants consisted of 35 male and 9 female military high school students (m=23, 1 years). On the basis of initial maximal performances in bench press the participants was divided into two experiments groups and one control group. Intervention groups performed a specifically designed push up program on a vibrating plate respectively a step board during 12 weeks Initial load at 60 % of 1 RM showed an average of 46, 5 kg. All groups showed an average increase of 13 kg for each person after 12 weeks.

Holmen Skog, region Norrköping, is located in an area with good potential for backhauling because a large number of geographically scattered mills. However, despite these factors there are many difficulties preventing the realization of this potential. The purposes of this study were twofold. First, from a hauling contractor perspective, to calculate backhauling profits and suggest a profit sharing scheme. Second, to identify and quantify obstacles and possibilities for realization of backhauls.The study required the use of three different types of methods.

In past decades information technology has changed the conditions of organizations, not at least within the industry. Advanced IT systems have become a fact in order to cope with rapid changes in the market and to effectively manage an organization?s knowledge. When organizations became more flexible and customized expectations from customers and stakeholders also become higher. These expectations and guidelines are documented in a company?s management system, which can be designed differently depending on what standards the company chooses to implement.

Marinediesel has, to meet there customers needs for a suitable sterndrive to powerboats, developed a prototype. The prototype is currently in the testing phase. The opportunity to test the sterndrive under load inside the workshop has not previously been possible. Until now the drive has been tested in a test bench without any load on the propeller axle. The prototype has also been tested under real conditions mounted on a boat.The idea with my thesis was to create a test bench that can run around the clock in order to be able to test things like wear and service intervals and other things that require that the test interval is long.

ÅF Test Center in Borlänge had a need to expand their capacity for compressive and tensile strength tests. They wanted to do this by using a hydraulic cylinder, which they already possessed, to apply the force with. This required a load receiving structure. The aim of this work was to design and dimensioning a test bench for a cylinder marked NIKE 300 tons. The work would result in a completed design proposal on a test bench which could manage to run the compressive and tensile strength tests of up to 3000 kN.