The purpose of this thesis is to examinethe possibilities for adding a floor to anexisting building using the two materialswood and sheet metal profiles as the loadbearing structure. An apartment buildingfrom the 60s has been used as referencehouse. Two different suggestions for thedesign are presented in the rapport. Oneof them has been analyzed with wood andsheet metal as the load bearing structure.Using the old constructional calculationsand blueprints of the existing buildings,the load bearing capacity has beencalculated. In the calculation programFEM-Design the building has been testedwith the loads that an extra floor wouldgive.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis is to evaluate and update load curves for Fortum Distribution AB. Theload curve method is a tool used to forecast the strain of an electric grid. The method is based oncustomer annual energy consumption, outdoors temperature as well as customer category. Theload curve method was established by Svenska Elverksföreningen at the start of the nineties andfocus was put on standardizing annual energyconsumption, in order to make the method usableacross the nation. Present consumption patterns have changed since the original load curves wereproduced, which leads to a need to update the load curves.The work began with an update of present load curves according to recommendation taken fromanother earlier thesis.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

This master of science thesis is focusing on how the fault handling on hardware connected toa control unit on a Scania vehicle is working. To the hardware counts buttons levers, sensorsand CAN. The work has been concentrated upon how the fault handling is working and if it ispossible to find any new fault modes.The control unit that has been studied is called the Coordinator and is the core in Scanias threenetworks of control units. The Coordinators work is to transmit messages between the threenetworks and to process signals from buttons, levers and sensors. The values is then usedinternally or is sent to other control units on the CAN networks.

Fiscal policy and its consequences have attracted much attention on both academic and societal level, in Sweden and elsewhere. However, the dependence between fiscal policy on municipality level and business cycles has only recently sparked a debate among Swedish economists. Studies point out that a law which came to force in 2000, balanskravet, may have caused municipalities to lower expenditures, alternatively raising taxes, during recessions. This thesis examines how the level of municipality taxes depends on business cycle fluctuations and the impact that balanskravet has had on this correlation. We employ econometric regressions, with annual data covering the period 1980-2014, to enable an analysis of the dependence between taxes and business cycles, both before and after the introduction of balanskravet.

The Homogeneous Charge Compression Ignition (HCCI) engine is promising in terms of lowNOx, low particulates and high efficiency. Due to its homogeneous charge, where thecombustion starts almost simultaneously from a number of points in the combustion chamber,only lean mixtures are possible to burn because of the resulting rapid combustion, which is muchfaster than the combustion in an SI-engine or a diesel engine. When richer mixtures are used thecombustion will start earlier and also be more violent.To phase the combustion later and lower the combustion speed, external cooled EGR can beused. The EGR-system used in this thesis uses a divided exhaust channel where one channel andits corresponding valve are used only for transporting EGR back to the intake system.Consequently the EGR-valve is connected to the intake pressure. This system is called Direct-EGR (D-EGR).Engine tests verified that the CA50 indeed is phased later when cooled EGR is used.

The purpose of this thesis is to investigate the fatigue life of two components in different hydraulic quick couplings. The crack which initiates the fatigue failure usually occurs in the bottom of one of the threads. Thus, the threads in the coupling are carefully investigated. A few different approaches for determining the fatigue life are studied for each component. CAD (Computer Aided Design) models for both components are created and analyzed with FEM (Finite Element Method).

This master's essay is about seasonality in Bristols slave trade until the American Revolution 1776. The essay uses the Voyages database as the primary material. The essay's method is to study monthly distribution at different points of the slave trade ? the departure from Bristol and the arrival at the American destination. The seasonality of slave purchases in Africa is primarly studied through the monthly distribution of departures from Bristol for a specific region in Africa.

A problem in the field of district heating is the oil burners needed to provide power when a peak load occurs. One possible way of reducing the needed amount of oil is to reduce the power demand for space heating in the district-heating substations when the need for district heating water exceeds a certain limit. This can be done by use of a locally working controller function.In this Thesis the options concerning load priority are evaluated. To evaluate the potential for using controller functions concerning peak load priority an experiment was brought out in a chosen district-heating substation. The impact on the indoor thermal comfort during a heat reduction was also taken into account.

The objective of this M. Eng. Diploma work was to validate the new version, CASMO-5M, and compare the results with CASMO-4E, by using the same input in both programs. The tasks that were included in this work was to compare TIP-measures, k-effective curves (warm), k-effective curves (cold), the effect of void on k-effective, the isothermal temperature coefficient (ITC), the moderator temperature coefficient (MTC), damping ratio calculations, internal effect in a fuel bundle of a BA-rod, the speed of BA-out burn, impact of xenon, falling control rod, margins and isotopes.The TIP-measures showed that the differences were small for all reactors, at most, 6% nodal improvement by C5M (Casmo-5M) for Oskarshamn 3. The warm measurements of k-effective showed that C5M had a higher value for all cycles of Oskarshamn 1, 2 and 3 in comparison to C4E (Casmo-4E).

This work is a part of the project ?Våtmarker i odlingslandskapet ? uppföljning av miljömålen? (Wetlands in arable land ? following-up of the environmental goals). The main objective with this project is to study nitrogen and phosphorus retention in a constructed wetland by using mass balance calculations. Continuous measurements of nutrients and water flow through the inlet and the outlet of the wetland are made. However, substantial amounts of nitrogen and phosphorus were assumed to reach the wetland with a drain-pipe transporting wastewater from nearby houses (10 persons).

With increased milkproduction in our dairy cattle, comes a risk for a reduced fertility. Studies performed on animals and humans have shown that it is possible to manipulate the oestrous cycle through exposure to pheromones. This means that pheromones could potentionally be used to make reproduction more efficient. To evaluate the bioactivity of the substances in question, there is need for a bioassay. In insects, pheromones can induce a changed cardiac activity.

Every day we make numerous decisions. Some are better than others. Intuitive decisions usually results in less good decisions when we do not reason about our choices. Research has been interested about the process that is behind how we make good decisions. Decisions we face every day, such as when we shop, determined using various mental shortcuts that we use unconsciously.