This Master thesis is about a postal- and telegraphic building in Eskilstuna, Sweden. The construction methods for the specific building and buildings in general from the same time are described. The purpose of the report is to describe the loads acting on the building and how it has been built and why it has been rebuilt during the years. After this, possibilities of reconstruction and adaptation for today?s demands can be evaluated.

In published studies it is found that the fuel consumption on a forwarder is relatively constant, on time basis. A certain variation between different sizes of forwarders occurs as well as between different working elements. The aim of the study was to establish a forwarders comparatively fuel consumption when driving on road and in the terrain, loaded and unloaded, with high and low gear and with high and low speed as well as with hydrostatic and hydrodynamic transmission. A hypothesis was that low rpm gives lower fuel consumption on distance basic, at all trials. The test driving was made with a Hemek 750 which is a three geared hydrostatic machine and with a Hemek 700 which is a hydrodynamic machine with six gears.

The goal for this master thesis project has been to investigate the power quality in adistribution grid, which has a high fraction of dispersed power production due towindmills. The study has been done on a grid in Laholm South of Halmstad, whereapproximately 45 windmills are connected to the distribution grid owned by SHKEnergi. The investigation has been focused on to two radialy fed 20 kV lines, wheretwelve windmills are connected.Voltage variations have been studied by creating a model of the grid in the simulationprogram SIMPOW. The largest deviation that has been found in any point of the gridis ±1.9 % of the nominal voltage. This deviation is a result of varying powergeneration from the windmills and the voltage regulation at the connection point ofthe line.

The thesis presents an optimally designed kinematic structure for a new 6-DOF haptic devicebased on TAU configuration. The configuration of the TAU-2 proposed by Suleman Khan andKjell Andersson [1] was modified and its mobility was verified by using Grübler criterion tohave a 6 DOF. Analytical kinematic models for the inverse and forward kinematics weredeveloped for the haptic TAU configuration to determine a set of optimal design parameters.Kinematic performance indices such as volume of the workspace, kinematic isotropy and payload index, were defined based on the singular values of the Jacobian matrix. The Jacobianmatrix was scaled to homogenize the physical units. The Jacobian matrix dependent on theposition and orientation of the end-effector gives local isotropy and pay load index, so globaldesign indices were defined, which represent the performance of the mechanism in the wholeworkspace.

Emotron is a company specialised in developing, producing and marketing equipment to con-trol, monitor and protect processes and machinery driven by electric motors, with an applica-tion focus. Examples of uses for their products are fans, pumps, lifts and cranes.The project is to look at Emotrons end of line test. The company has seen that at the final test-ing there is a bottleneck that restricts the outflow and prevents an increase in the number of tested products.The purpose of this project is to review how Emotrons end-of-line test works today and if there is a possibility to make the test more efficient in such a way that the quality is not at risk, while increasing the outflow of tested products.The projects first step is to look at and analyse what is causing the bottleneck at the end-of-line. When the analysis is complete, the next step is to review whether there is a possibility to solve the bottleneck and if so in what way can this be done. Emotrons most overall objective of the project is to increase the outflow of the number of tested products without jeopardizing the quality.An analysis has been made on frequency inverters, soft starters and shaft power monitors.

BACKGROUND: Today?s societal changes, including high rate of change and increasing information flows, are increasing the demand on the individual mental capacity. It becomes increasingly difficult to analytically process all the different dilemmas and everyday decisions as individuals have a limited mental capacity available to make these decisions. Thus, it has been suggested that ego-depleted relies more heavily on intuition, which is less burdensome, when making decision. However little is known about to what extent intuitive decisions differ from analytic.

Nutrient enrichment is the main cause of the increasing eutrophication process in the Baltic Sea during last century. A prerequisite counteract this process the load of nutrients to the Sea must be investigated. The large contribution of nutrients to the Sea is caused by emission from the rivers within the drainage basin. For the total emission of nutrient into the Sea the retention process in the rivers has big influence. This process in the river system has been assumed as a not important part of the nutrient cycle.

The goal for this master thesis project has been to investigate the power quality in adistribution grid, which has a high fraction of dispersed power production due towindmills. The study has been done on a grid in Laholm South of Halmstad, whereapproximately 45 windmills are connected to the distribution grid owned by SHKEnergi. The investigation has been focused on to two radialy fed 20 kV lines, wheretwelve windmills are connected.Voltage variations have been studied by creating a model of the grid in the simulationprogram SIMPOW. The largest deviation that has been found in any point of the gridis ±1.9 % of the nominal voltage. This deviation is a result of varying powergeneration from the windmills and the voltage regulation at the connection point ofthe line.

The goal of this thesis is to design an attachment between a duct and a pod. A pod is what could be compared to an outboard engine for larger vessels. The pod is placed on the outside of the ship?s hull and can rotate 360 ?. A duct is a large steel ring that can be placed around the propeller on the pod to increasethe propulsion force of the ship in lower velocities.

Hydropower is an important source of energy in Sweden and accounts for about 46 % of the total energy production. Sweden has about 1 200 hydropower plants and with the intention of raising the pressure head of the water and to store water, dams are built by the power plants. The storage reservoirs make it possible to adjust the energy production by demand and season. Dams in connection to the reservoirs are subjected to additional loading during periods of high floods or when an icecap in the winter is formed on the reservoirs. In order to maintain the dam safety, the power companies in Sweden are working with guidelines for dam safety from RIDAS.

The Goal with this Master of Science thesis is to expand the possible turbine efficiencymeasurements on an exhaust turbocharger. It was done as a part of the CICERO competencecentre. To feed the turbine with air a special flow rig has been used. Instead of loading theturbine by just restricting the compressor flow a docking system for an electrical dynamometer isdesigned to use the dynamometer as an additional loading source. By using an electricaldynamometer as loading device for the turbine, measurements are not depending on compressorperformance.A large part of the work consists in designing accessories for the dynamometer.

In Sweden, the eutrophication of lakes, water courses and the coastal areas is considered the major threat to aquatic ecosystems and therefore actions taken to reduce the nutrient load to aquatic system including the Baltic Sea has high priority. There are many different sources of phosphorous and nitrogen and domestic wastewater is one contributing factor to the high load. Especially waste water from households that is not connected to municipal sewage treatment or a local small scale plant with appropriate nutrient removal efficiency is considered a problem. These types of households are quite common in rural areas in Sweden and in areas where summer houses has been converted to permanent living. Swedish legislation now permit the municipalities to decide in which areas within the municipality higher demands of the local small scale treatment facility should be met by the households (i.e.

The project contains a force analysis of the vertical axis wind turbine Lucia's supporting arms and a measuring device to experimentally measure the forces is made. The forces between the supporting arms and the tower are calculated theoretically and then simulated by a computere. A measuring devise is then designed to measure the forces experimentally. The forces acting on the attachment between the supporting arms and the tower is primarily the centripetal force, gravitational force and the aerodynamic forces on the rotor wings. The maximum forces were theoretically calculated and is 13.38 kN along the x-axis, -0.25 kN along the y-axis and then 0.5 kN along the z-axis.

Regulations on the exhaust emissions of HD-diesel engines are becoming more and more stringent, and therefore, emission after-treatment systems are commonly used. These systems rely on catalytic conversion of NOx,CO , and HC emissions, and are thus dependant on temperature. At low load of the engine, exhaust temperatures are not sufficient for the after-treatment components. Therefore, means to increase the exhaust temperature while maintaining low emissions and fuel consumption are needed.The focus of this project has been to develop strategies for the lift profiles of exhaust and intake valves in the engine, with the goal to raise exhaust temperature in combination with low emissions and fuel consumption. The strategies have been tested in a single-cylinder research engine equipped with a hydraulic variable valve actuation system.

AbstractIn my ambition to improve my writing and reflect upon the way I express myself I am, in this paper, going to study the purport of the term pathetic. I do this by inquiring what lexicon and dictionaries say about the term and by studying how the word can be used in present time. I apply the contemporary usage of the term pathetic to my own text and then adapt my text from how the term is used in our time. By doing this I clarify to myself how I look at my own literary style, what I want my writing to be like and how the progress in my composing is developing. According to the interpretations I have done, I find meanings like ?ridiculous? and meanings which have to do with strong emotions as well.