Over an extended period of time there have been plans to establish a shared facility in Lennheden to extract groundwater from the Badelunda esker to provide drinking water for the cities of Borlänge and Falun. The city of Falun is dissatisfied with the quality of its drinking water and the city of Borlänge is concerned about the risk of contamination of its existing groundwater supply at its current location. To provide a basis for a decision on this issue, the company Midvatten AB has been commissioned to perform hydrogeological investigations in the area of Lennheden.The purpose of this thesis is to design a functional groundwater model of the area between Lennheden, place of planned extraction, and Övre Tjärna, place of existing extraction, to get a better understanding of the groundwater situation in the area. A groundwater model enables simulations of different scenarios in risk assessment and contaminant transport. The aim of the thesis is that the model can be used as an aid in Midvatten?s investigations in Lennheden and that it also can be used in future projects in the area.The model has been made in Processing Modflow 5.3 and encompasses an area of 19,5 × 11 km along the Badelunda esker and the river Dalälven between Djurmo and Frostbrunnsdalen.

Future emission legislation puts great emphasis on increasing the efficiency of the engine, thereby reducing fuel consumption. The tribological contact between cylinder liner and piston ring is where an great amount of energy is lost due to friction, and by reducing these losses an reduction in fuel consumption can be achieved.The aim of this thesis was to evaluate the tested piston ring coatings against a plasma sprayed cylinder liner and rank these combinations of materials for friction and wear resistance. The coatings that were tested was Cr + Al2O3, (Al,Cr)N, two types of CrN and WC / C.The experimental tests were performed with a so-called pin-plate, where used oil with addition of an acidic mixture of sulfuric and nitric acid to mimic the acidic condensate formed when exhausts recirculate, were added with a continuous flow. The results were then analyzed by weighing, studies by optical microscopy and scanning electron microscopy (SEM) and profile measurements.The results from each material combination were that the plasma coated cylinder liner wears too aggressively in order to yield a ranking of the piston ring coatings based on the parameters of friction and wear resistance. It is therefore proposed that an alternative coating on the cylinder liner should be developed, lacking the large abrasive wear on piston rings and that can withstand the corrosive environment resulting in engines equipped with EGR.

Geothermal energy can be extracted from an aquifer, where the groundwater is used as heatexchange medium while heat and cold are stored in the surrounding material in the aquiferand to some extent in the groundwater. Application of aquifer storage for the use ofgeothermal energy is mainly used in large scale facilities and is limited to sites with suitableaquifers in the form of ridges, sandstone and limestone aquifers.Löwenströmska hospital in the municipality of Upplands Väsby, north of Stockholm, islocated nearby the northern part of the Stockholm esker. This means that it can be profitableand environmentally beneficial for the hospital to examine the possibilities of aquifer storagein the esker material next to its property.The purpose of this master thesis has been to investigate if geothermal energy storage with aseasonal storage of heat and cold can be applied within Löwenströmska hospital?s propertyarea using groundwater modeling. A hydraulic groundwater model was constructed inMODFLOW based on a simplified conceptual model of the groundwater system.

Want to help making the world a better place? Do it with HypOCycle!HypOCycle is a bachelor thesis that started in September 2007. The project is owned byLars-Johan Hjertz and Erik Westerlund.HypOCycle is probably the only bike in the world that has a linear pedal movement. Themovement comes from a new engine technique that hasn?t even been brought to themarket yet.

When protection zones for wells are delineated, it is important to acquire good knowledge about possible travel time from different points in the catchment area to the well. Often, simple analytical methods are used for estimating travel times and the assumption is made that the hydraulic conductivity is relatively homogenous within the aquifer. Nevertheless, many aquifers are strongly heterogeneous which may lead to differences between estimates and actual travel times. As a part of the process to develop improved methods for delineating protection zones for groundwater supply wells, a tracer experiment was performed in a glaciofluvial esker formation in Järlåsa. On the basis of the experiment, a numerical flow model was created for the test site.The purpose of this master?s thesis was to apply the flow model to an aquifer where the hydraulic conductivity shows great variability and should be described by a stochastic distribution.

This report treats a Master Thesis performed at Scania CV AB. The task was to create a computer model of a hydraulic actuator system in the software AVL Hydsim. The system consists of two spring-loaded masses with surrounding hydraulic components. The purpose of the model is to study phenomenon and problems in the system, as well as to be a support in the development of the system. It is not supposed to be used to study absolute values in its current form.

Estimation of the variation in the integrated hydraulic conductivity around the Tunåsen infiltration facility - An investigation of the effects of uncertainties in existing informationAlmost half of Sweden?s drinking water volume is produced from groundwater. The main fraction of this is extracted from eskers, some of which allow for very large extraction rates. Despite this, the groundwater volume is not sufficient in some areas. This has led to an extensive use of artificial recharge.In Uppsala, the total volume added through artificial recharge is divided between four infiltration facilities.

?Optimizing the workflow of hydraulic reservoir tanks? is a degree project made by Jonas Olsson, student within the faculty of technology and science, during spring semester 2012. The project comprise 22,5 ECTS.Volvo Construction Equipment, located in Arvika, was the client in this project. The mentor at Volvo CE was A?sa Barck, and the mentor at Karlstad University was Monica Jakobsson.

This master thesis was conducted during the spring of 2014 at Atlas Copco Rock Drills AB in Örebro. The purpose of the thesis was to develop a simulation model of the rotation system for a hydraulic rock drill. In the future, the model will be used to investigate the phenomena called ?jerky rotation?. In order to validate the simulation model a test bench was designed and tests were made.

This thesis deals with the numerical 3D simulation of a four stroke, spark-ignited, internalcombustion engine, which is mounted on a high performance motorcycle. The work, carried outin collaboration with Politecnico di Milano and MV Agusta, focuses on the simulation of theintake, compression and expansion stroke, including combustion simulation, using an opensource CFD code.Simulation of internal combustion engines offers a great challenge in the field of CFD research.Moving boundaries of the solution domain, caused by the motion of the piston and valves, leadsto deformation of the computational grid, with decreasing quality of the solution as result. Basedon this, a previously developed mesh motion strategy was employed where a number of meshesare used to cover the whole simulation cycle. Within each mesh interval the internal cell pointsof the mesh are moved to account for the boundary motion of the piston and valves. This strategywas previously applied to simplified geometries as well as real engine geometries.

This Master Thesis is a product development project that has been carried out incooperation with Metso Paper Sundsvall AB. The task has been to develop a holdingsolution that generates force between two rolls and to evaluate the new solution withrespect to functionality, manufacturing, structural stability, costs, assembly etc. Theroll holding solution is a system that is part of a rollpress. The rollpress is used towash and dewater pulp. The existing solution creates forces that have to be absorbedby the gable of the press.

Test bench for air bearingsThis thesis work consisted of bringing forward and defining the test parameters relevant for a test bench and constructing a test bench that can test and verify the largest existing air bearings that are of use in Micronic Laser Systems AB machines. Because the knowledge about air bearings is limited it is thought that with the help of the test bench the knowledge would increase and in that way improve the air bearings.After learning more about air bearings and their purpose at Micronic Laser Systems AB, I started the concept phase for the test bench. For each part in the test bench I consulted my two tutors, Torbjörn Hedevärn and Johan Bergqvist, at Micronic Laser Systems AB. The final concepts where documented as 3D-modells in Solidworks and some of them have been tested in Solidworks FEM-program.The test bench is designed so that, with the help of a pneumatic cylinder, 25 kilo weights are placed on the air bearing to test its stiffness, damping and the pressure performance under its surface area. To test these parameters the test bench has to have a pressure meter, accelerometer and a microcator.

Regulations on the exhaust emissions of HD-diesel engines are becoming more and more stringent, and therefore, emission after-treatment systems are commonly used. These systems rely on catalytic conversion of NOx,CO , and HC emissions, and are thus dependant on temperature. At low load of the engine, exhaust temperatures are not sufficient for the after-treatment components. Therefore, means to increase the exhaust temperature while maintaining low emissions and fuel consumption are needed.The focus of this project has been to develop strategies for the lift profiles of exhaust and intake valves in the engine, with the goal to raise exhaust temperature in combination with low emissions and fuel consumption. The strategies have been tested in a single-cylinder research engine equipped with a hydraulic variable valve actuation system.

Available as pdf.

This thesis work has been performed on request by SWT (Scandinavia WeldTech AB). SWT manufactures, develop and sell ready to assemble building systems for concrete rafter beam applications. The beams in this system consist of a u-beam that is welded to a flange. To be able to fill the beams with concrete there is holes in the beams top end. The holes are made in a ?punching machine?.  These holes are cut out and the remaining steel piece is bent down in the u-beam.