In the process laboratory of Metso minerals (Sala) AB, continuous tests have been made with a laboratory unit High-Rate thickener. The tests are made in order to compare three methods of thickening techniques of suspended solids. The three techniques are High-Rate thickening, conventional thickening and lamella thickening. The High-Rate and the conventional trials are based on a continuous method, while the lamella thickener is based on batch trials. Because the lamella thickener is based on batch trials and there were some optimization problems with the adding point of the flocculant at the continuous trials, it was not feasible to compare the lamella thickener with the other two thickener types.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

Sweden has an environmental goal to achieve until the year 2020. To achieve this goal the construction business has to take an initiative to use the modern techniques that are available to lower the energy consumption I buildings. There?s also a debate going on today regarding the energy demands set by the Swedish government through Boverket, some communities throughout Sweden thinks that the demands are to low and have therefore set up own demands regarding energy in buildings.The possibility to construct energy-saving buildings is today very great, with energy-efficient heating-systems and dense climate envelope. The interest to raise energy-efficient buildings have also increased as a consequence that the population have become more aware about their impact on the environment.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

The author has, with the help of AK Consultancy Indoor Air AB, formed a series of questions regarding moisture problems in buildings and how these are handled in extreme climates with high temperatures and a high relative humidity. Furthermore to analyse and indentify key material that makes a construction safe against moisture problems. Ventilation, AC and the choice of materials have in a later stage of the thesis been investigated to enhance the knowledge of moisture protection. The research for this report includes measurements on existing buildings, calculation models on the building envelope for analyses and the ingoing materials of the envelope. The health aspect of moisture problems related to ?sick building syndrome? has been included and interviews have been conducted to gather relevant information.A study of the American system, ASHRAE, American Society of Heating, Refrigeration and Air Conditioning Engineers and the standards used in Singapore has been made to highlight the difference.

This report has a dual focus. The first goal was to increase the knowledge of how the use of electricity in a residential building is distributed. Electricity in residential buildings is used for lighting in common areas, elevators, pumps and many other appliances. The electricity used for these different parts is to a great extent unknown. A few studies have been carried out and the result of these is referred to in this report.By means of measurements and approximations the use of electricity for various appliances became known.

This report has a dual focus. The first goal was to increase the knowledge of how the use of electricity in a residential building is distributed. Electricity in residential buildings is used for lighting in common areas, elevators, pumps and many other appliances. The electricity used for these different parts is to a great extent unknown. A few studies have been carried out and the result of these is referred to in this report.By means of measurements and approximations the use of electricity for various appliances became known.

This report has a dual focus. The first goal was to increase the knowledge of how the use of electricity in a residential building is distributed. Electricity in residential buildings is used for lighting in common areas, elevators, pumps and many other appliances. The electricity used for these different parts is to a great extent unknown. A few studies have been carried out and the result of these is referred to in this report.By means of measurements and approximations the use of electricity for various appliances became known.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

Moisture damage in buildings is a serious issue that leads to problematic consequences and high economic costs. Despite the knowledge and awareness existing about moisture problems, extensive damager still occurs today. Studies of moisture in the exterior wall constructions shows that the issue if often caused by rain and water intrusion. These kinds of problem result in major costs usually because the companies have to replace the material and structural components and also in some cases tear down large parts of the buildings.The work includes moisture theory and descriptions of four different exterior wall constructions, wood stud wall with plastered facade, exterior wall with wood facade, exterior wall with concrete, and exterior wall with brick facade. Our thesis work describes how the constructions are affected and moisture damage due to water intrusion.

This report has a dual focus. The first goal was to increase the knowledge of how the use of electricity in a residential building is distributed. Electricity in residential buildings is used for lighting in common areas, elevators, pumps and many other appliances. The electricity used for these different parts is to a great extent unknown. A few studies have been carried out and the result of these is referred to in this report.By means of measurements and approximations the use of electricity for various appliances became known.

certain building or environment can get a protection as a notable building if it contains certainvalues. These values are established by a certain category of people from the cultural sector.These people use established criterions to define the cultural value of the object. The objects canbe evaluated differently depending on who has done the evaluation. The people who protect thecultural environment and choose which buildings that are to be defining as notable buildingsoften uses a special model to characterise the different cultural values. This model is produced bya man called Axel Unnerbäck.

Today automatic milking systems (AMS) are growing in popularity. In these systems the cows are loose and have to get to the robot and the feed on their own. The cows ranking in this system affect their welfare. In this study data from seven years in an AMS was used and analysed. The aim was to investigate how ranking could affect the behaviour of the cows at milking and at feeding.

To build High-rise buildings made of timber has for long been limited by national laws, due to the lack of knowledge in engineering solutions. Frame structures made of wood has for a long time been associated with major fire hazards and consequently lower safety and this connection is still being made today. The increased environmental awareness in recent years has contributed to the exploitation of indigenous building materials, including wood from our own Swedish forests and has become increasingly common. Increased knowledge about how structures behave in fire and how they can be protected in order to achieve safe timber structures has resulted in a growing interest in these structures in the construction industry. Research in the area is constantly updated and new laws allow any number of storeys in wooden buildings in Sweden as long as the performance requirements are fulfilled.The main part of this work has involved calculations of the fire resistance and load bearing capacity of floor and wall constructions.

This bachelor?s thesis examines the tradition of half-timbered buildings in V?stra G?taland County as there is a current lack of research on this building category in this region. The lack of knowledge may lead to the loss of potential cultural heritage values if these buildings do not receive attention. Therefore, the study aims to provide a more comprehensive understanding of its role within the region. The goal is to expand and nuance the existing research on the Swedish building tradition, particularly in V?stra G?taland County and the general Swedish half-timbered tradition.