When several production units provide a district heating network, water is pumped from different directions. When the flows from the plants finally meet in the network, the water can be completely still. These places are called zero flow zones. In district heating networks with several plants, which also have different supply temperatures, large and frequent temperature fluctuations can occur when the zero flow zones move. This may cause wear on the pipes, a phenomenon called low cycle fatigue.For this reason it is important to examine where and when zero flow zones that cause temperature changes occur.

This rapport is result of a project. The purpose of which was to design a circuit that is used in a heat glove. The heat glove is the technical aid which provides heat inside a glove.It is specially suited for old people who have problems with cold hands because of decreased blood circulation.There already was an old circuit in the glove that gives a constant current which develops heat from battery to glove through a circuit. The temperature is between 32 and 34 degrees.The problem with the existing circuit was to regulate the temperature. There is only on/off switch and there is no way to adjust desirable value of the temperature.In order to solve the problem the old circuit was investigated.

The objective of this report is to present a review of the studies which has been carried out up to days date concerning how temperature affects vegetables physiologically when it comes to their health inducing as well as quality reducing features. The essay therefore starts off with defining what is meant by the terms health promoting and quality reducing features. It then moves on to describe how different subspecies of Brassica oleracea, that is to say vegetables such as broccoli, cauliflower, Brussels sprouts and kale, is affected by temperature. B. oleracea was chosen because the species contains several commercially interesting subspecies and therefore provides a broad field even though only one species is assessed.

Quality is the main focus in management of all laboratories. Accurate results of the analyses are not only determined by the analytical procedure but also by preanalytical factors. In the total analytical process of clinical specimens, there are many possible preanalytical sources of error. Monetoring of temperature on test samples of the transport boxes is one way to reduce the mistakes in the preanalytical phase.In this study, four laboratories from primary health care were invited to participate. The temperature has been measured on test samples of the transport boxes being delivered to the laboratory.In three cases the temperature remained within the limits, but in the fourth case the temperature varied more than the allowed interval.

Optimizing energy systems is, in Sweden, as in many other countries, of growing interest. District heating systems are no exception. In 2012, 285 out of 290 municipals in Sweden had district heating in use and the majority of these systems have a higher return temperature than that which is possible with an error-free substation of day current technology. To, when possible, lower the return temperature is a way of increasing the effectiveness of the district heating system.This study means to investigate, through simulations and calculations, how big of a reduction in production cost a lower temperature in the city of Ystad?s district heating system would correspond to.

A Swedish electronics company wants to make the cooling of one of their electronic components more efficient. They propose that a retrofit liquid cooler is the way to achieve this goal. The current air cooling has high energy cost due to the high amount of power needed to power fans and heat exchangers. Using high volumes of air for cooling also leads to noise pollution. The conversion from air to liquid cooling would possibly make the operation of the electronics more cost efficient and less noisy.The purpose of this project is to theoretically evaluate different concepts of drawing the heat generated by the electronic component in to a fluid, using numerical calculations in Matlab and FEM simulations in ANSYS.

In this study the hygienic quality of minced moose meat was examined with regard to the prevalence of different bacteria. The methods used are described in NMKL, "Nordic Method Committee for Food". The results show that the levels of Escherichia coli and coagulase positive staphylococci in the meat are too high. The reason for this might be environmental factors, such as High temperature and humidity during the time when the carcasses are hanging and when the meat is cut up..

Female growth, number of eggs and egg growth of Daphnia pulex were studied at four temperatures, 12, 16, 18 and 20°C. I hypothesized that female growth and number of eggs would be lower and the size of the eggs larger in the presence of a predator (kairomones) than in its absence. This effect was expected to be more evident at lower temperatures. I could not find any effect of kairomones on female growth, number of eggs or egg size, although there was a weak tendency for an effect on number of eggs. There was, however, an effect of temperature, regardless of predator treatment (i.

The master thesis, conducted at Metrima AB, concerns the development of a non-intrusivedistribution meter as a basis for individual tap water billing in apartments.The project is conducted in response to the market interest in individual tap water billing inapartments as an answer to environmental concerns regarding water consumption. Due to thehigh installation cost of traditional water meters, a new method of determining waterconsumption, without having to cut water pipes, is proposed.The proposed method distributes the total water consumption for an apartment complex toindividual apartments according to distribution meters, measuring water run-time, in eachapartment. The water run-time is estimated by measuring the water pipe?s outward vibrationsand temperature changes.A test environment was established and a prototype built, using a tilt- and vibration sensor forvibration sensing and a precision temperature sensor to measure temperature changes. As bothsensors work well in the test environment, further testing was done in 3 apartments for aduration of 5 days.

In the spring of 2014 Sweco Systems AB were commissioned to design a ventilation system for a newly built preschool in Linköping. Terms from the client was that it cost efficiency would cope with the energy demands that are placed on the building. The unit chosen was a cross-flow heat exchanger, and this work is to compare it with two other heat exchangers to see if a more energy and cost efficient could have been chosen. The heat exchangers that was chosen for the comparison was a rotating- and a counterflow heat exchanger. Simulations have been made to the different heat exchangers by the manufacturers.

This report describes the building of a computer model that makes it possible to simulate the thermal climate in a greenhouse. The computer model is built on the physical theory of heat exchange that occur in a greenhouse, such as radiation and convective heat exchange. The model also includes the heat storage that is active in a greenhouse.The computer model is used to simulate the thermal climate in a greenhouse under three periods, winter, spring and summer. It also investigates which effect a concrete wall has on the thermal climate in a greenhouse. The purpose of putting a concrete wall in the greenhouse model is to investigate the possibility to store heat during the day and then use this heat when the temperature drops during the night.The result from the simulations shows that a concrete wall levels the big difference in temperature that normally occurs under a day in a greenhouse.

The project focus on combustion of softwood pellets and pellets in a 40 kW grate fire reactor at TEC-Lab. Dept Applied Physics and Electronics at Umeå University. Experiments were performed at four primary airs to fuel ratios (0.7 to 1.3), where aspects such as temperature profile, levels of gases (CO and NO), sintering-/-slagging and unburned fraction of the ashes were studied. Four different fuel loads were used for wood pellets (10, 20 and 30 kW) and one fuel load for straw (10 kW). Combustion of straw proved very difficult to ignite, and also led to other combustion-related technical problem such as slag formation due to the relatively low melting temperature-/-slag temperature of the straw.

If a building is heated by a heat pump, it is of high importance that the heat pump has a high coefficient of performance. An exhaust air heat pump extracts heat from the building?s exhaust air. The air has a relatively high and constant temperature all year around, leading to a high seasonal coefficient of performance. This thesis examines whether it is profitable to complement an exhaust ventilation system with an exhaust air heat pump in an apartment block that already has geothermal heat pump, district heating, oil- or biofuel heated system.

This report is made as a literature review, focusing on the work done to increase understanding of efficiency in the categories of substations and secondary heating systems, with respect to the deviation from the theoretically possible cooling off in the distribution network as well as the economic benefit that appear. The main purpose of a considerable part of the literature used in this report addresses the issue of identifying individual causes of reduced cooling in district heating systems. These literature resources have been compiled and summarized as part of the report.The technology of district heating is associated with benefits such as better use of the energy in a fuel. This is the case of cogeneration plants where serial generation of electricity and thermal energy increases efficiency compared with the parallel generation where heat is generated locally and electricity is generated centrally. Serial generation thus allows for lower primary energy demand.

The purpose of this thesis work was to develop an automatic fault detection system for surveillance of bearing temperature in hydropower turbines. The parameters used except the bearing temperature were cooling water temperature and cooling water flow. A simple static model based on data sampled every minute was developed to estimate the bearing temperature. Then a detector for detection of change in bearing temperature based on the CUSUM-algorithm was designed. Since the amount of data was very small the developed model was too uncertain to be used in a working system.The designed fault detection system showed to work well for the available data.