The sound part is mainly practical and is dependent on concepts that have been tested through measuring with a sound level meter. The design part is more theoretical and has been verified with CAD models and finite element analysis.With a sound damping hood on the compressor the sound level is reduced with up to four dB. An optimized absorbent for the compressor space gives a reduction with three dB. By using the insulation for the heat water tank as absorbent we can see a sound reduction on the lover octave bands. A reduction like this is elsewhere hard to achieve as at it requires thick absorbents.By changing the today?s insulation to the heat water tank to a form of polystyrene polymer insulation the weight from the heat pump above can be transferred to the stable heat water tank.

Göteborg Energi has a surplus of district heating during spring, summer and fall. The heat surplus is due to a constant production of waste heat from oil refineries and heat from waste incineration over the year. It would be desirable to increase the demand for heat and the uptime for the newly built combined heat and power generation plant, Rya Kraftvärmeverk. One alternative could be to integrate Rya Kraftvärmeverk with a pellet production facility. By producing heat, electricity and pellet in a joint process the energy use can be decreased.

The aim of the study was to compare productivity in first thinning of birch stands, when either energy- or pulpwood was harvested. The systems total profitability was also compared by including forwarding and chipping costs. A Gremo 950 HPVR harvester was used and the same driver was used under the entire study. During the pulpwood harvest a Logmax 4000b harvester head was used and a feller buncher head made by Silvatec was used during the energy wood harvest. Six study unit pairs were located in a birch dominated stand outside Ängelholm in Skåne.

SAPA´s resource of waste heat is the basis for this thesis to investigate the possibility of energy assets in their cooling water and possible uses for it. The energy in the waste water is greater than the current need which has three uses which are (1) heating the factory, (2) converting liquid propane to propane gas and (3) local domestic heating. The average energy load that is available is 1, 7 MW and the average temperature in the cooling water is 41°C. The total energy load at dimensioning out side temperature is approximately 1,6 MW for the three current uses. The temperature is currently too low to be used directly in the existing systems so an upgrade is needed.

The primary purpose of this study has been to investigate the Swedish timber industry?s perception of compression wood. A secondary aim has been to describe particular areas within the production process where compression wood is likely to cause problems. This study has mainly been carried out as a questionnaire. In order to connect the findings to current research, additional information has also been collected by means of a literature review. The questionnaire has been intended for sawmills and wood-manufacturing companies from various production classes and owner categories, as well as from different parts of the country.

My questions at issue for this report has it´s beginning in the growing problems of thenegative effects of burning fossile fuels and the rapidly growing energyprices.1. Is it possible to design a micro scale powerplant?2. Is it economically interesting for a potential customer to by such a product?The aim with this report is therefor, with the help of design work and calculations, to answerthese questions and to create a platform for building a fully functional micro scale powerplant.The material used in the report is mostly product catalogs from various industries but alsostudy course littrature about steam engines.The result of the report is that it is fully possible to design a fully functional micro scalepower plant.

Increased resource efficiency in an energy system could result in large economic and environmental benefits. Tekniska verken i Linköping AB (Tekniska verken) is responsible for the district heating network in Linköping. Their vision is to create the world?s most resource efficient region. An important step towards this vision is more efficient usage of produced heat, something which could be achieved through integration of a seasonal heat storage in the energy system.

In order to reach the environmental targets, set up by the EU, there are many measures taken to make Sweden more energy efficient. In the housing and real estate sector, an installation of an exhaust air heat pump that reuses the heat in the exhaust air in order to lower the amount of acquired energy, is an example of such an action. The recovered energy can then be used for heating of radiators and tap water. This report aims to evaluate and compare three different systems using exhaust air heat pumps regarding COP, degree of coverage and cost savings. This study was delimited to only account for apartment buildings.The theory chapter describes the different conditions and factors that affect a building?s energy balance.

We are heading towards a huge switch of how energy is produced with fossil fuels being replaced by renewable energy sources. It is not difficult to replace the energy you use in the house and there is no need for futuristic technology. There are already many established products on the market such as high efficiency vacuum solar collectors, heat pumps & small wind power stations that can supply the energy being used in a house. The company Sol & Energiteknik SE AB in Huskvarna has many different products which can reduce the need for an outside energy distributor. An average house in Sweden uses 15 000 kWh for heating, 5000 kWh for tap water and 5000 kWh for electricity.

AbstractBackgroundThe Swedish district heat market of today is a subject being discussed regarding the reasonableness of the heat district supplier?s price settings. The issue is currently on a government level where a new investigation is being executed at the time of writing. Many real estate owners are growing tired of the situation where the heat district suppliers are taking advantage of their monopoly position, thus feeling that the price of district heating has been increasing far too much for many years. The market can be described as a natural monopoly because the real estate owner has no possibility to choose another supplier if they are unsatisfied with the present.

Sweden has long had access to low electricity prices due to the wide availability of hydro and nuclear power. This has now changed because of today's rising electricity rates resulting in increasing heating costs for properties, especially in the properties with electric heating systems."Ankaret" is a parish for "Svenska Alliansmissionen", which is located at "Gullbrannagården".The parish has installed electrical radiators and an exhaust ventilation system that makes the energy demand high due to the large ventilation flows. The building was built as the price of electricity was still low and would reduce energy use today by combining its heating system with an air/air heat pump. The heat pump delivers more heat into the room than the electrical energy that it uses. This lowers the electricity needs.

A high amount of dead wood is one of the most important prerequisites for high biodiversity on forest land in Sweden. Dead wood is most abundant in young forests, thinned forests, woodland key habitats and protected forest land. In old-growth forests most of the dead wood consists of logs and snags, whilst in managed forests a huge proportion of dead wood is made up of logging residues like stumps and FWD, fine woody debris (< 10 cm diameter). All these different types of dead wood may serve as substrates for epixylic bryophytes and lichens. However, few studies have been conducted on the relative importance of these different fractions of dead wood for the occurrence of bryophytes and lichens, especially when considering dead wood on thinned forest land.

The purpose of this thesis is to study whether there is a demand for sawn wood products of large dimensions and planed goods among Wallnäs AB:s customers. The thesis consist of two main parts, one survey among Wallnäs present customers and another one which purpose is to increase Wallnäs customer base. Finally there is a chapter that describes what properties the raw material has to have in order to produce the demanded products. The survey to the present customers was conducted through a questioner. A sample of those who stated an interest for either sawn wood products of large dimensions or planed goods, were later contacted for a telephone interview. To reach out to new customers, relevant companies has been identified through the Swedish Trade Councils data base and through the member list of the Timber Trade Federation.

En hanteringsutrustning för att underlätta förberedelser av gips på sjukhus.

Latent heat storage is a way to store thermal energy when a phase change material undergoes a phase change. The advantage of latent heat storage is the capability to store more energy per mass unit than other heat storage methods. The most commonly used phase change in latent heat storage is the transition between solid and liquid. Phase change materials can be divided into organics, inorganics and eutectics.In the Nordic electricity market the price of electricity is set every hour by Nordpool spot, which leads to price fluctuations because of changes in demand. The main goal of this report is to create a latent heat storage system in a single-family home and investigate the possibility to save money by charging the latent heat storage system when the price of electricity is low, and discharge when the price is high.The thermodynamic model consisted of a ?tube-in-tube? heat exchanger with phase change material in the outer tube and water as the heat transfer fluid in the inner tube.