The purpose of this essay is to draw attention to the obstacles that affects the internal trade of waste within the EU. The essay doesn?t in any way encourage pollution or illegal handling of waste but unfortunately there are large profits to be made from illegal destruction and recycling of waste and especially hazardous wastes. Therefore the dependable companies handling waste must access a market with fast and flexible (but predictable) regulations as well as lower transaction costs to help make the environment better and encourage a strive for increased recycling. There are examples where some waste only can be sent to a land-fill within the country but could be recycled in other EU-countries.

The aims of this project were to describe the circumstances around dogs being left alone in cars, to investigate owners? knowledge of the risks associated with leaving dogs in cars and the relevant legislation and, finally, to study how changes in the air temperature and air composition in the car affect the dog. The project consisted of a survey of the literature, a questionnaire part and an experimental part. An important conclusion is the importance of the level of knowledge of owners, since there are several ways in which an owner can prevent their dog from heat stroke and, in the case of an eventual accident, their action can have direct consequences in minimizing the long-term damage to the dog and even whether or not it survives. Fewer than half of the owners in the study knew that for a dog suffering heat stroke, the most important thing is to bring the body temperature down. Only a third of dog owners knew that if a dog is left in a warm car and showing signs of heat stress, then the police should be contacted and the dog quickly helped out of the car.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

This thesis examines a possible control strategy to minimize flow fluctuations in Uppsala?s district heating system. High variations in flow rate may lead to complications caused by hydraulic constraints in the district heating system. These complications, such as inadequate pressure and temperature levels, increase the risk of heat delivery failures. It is therefore important to avoid such situations both for the producer and for the customers.Typically, the forward temperature is controlled by using a rough correlation with respect to the outdoor temperature.

The aim of this essay is to examine the handling of plastic waste on a local level in the three municipalities of Gothenburg, Malm? and Stockholm. This is achieved with the help of guidance within the theory of Multi-level Governance. By applying the EU directive 2019/904, about disposable plastic, and examining the global plastic problem, the efforts to promote sustainable use, and recycling of plastic, is analyzed. The method involves a qualitative content analysis, where the 2022 waste plans of the three municipalities, ?Sveriges handlingsplan f?r plast? by the Government Office, and the 2019/904 EU directive constitutes the base of the study.

Chapter 1 defines the aim of the project and gives a general orientation about ground heat extractors. In chapter 2 physical processes that could be expected to be involved in the heat transport around a ground heat exchanger are discussed. It is shown from a literature study what amount of moisture transport due to thermal gradients there could be expected in a ground heat exchanger. The conclusion is drawn that the moisture gradient (Sr) is of same magnitude as the driving temperature gradient (°C). At the expected amount of increased moisture around the pipes the moisture transport could be considered to have a little effect on the brine temperature.

Norconsult AB has developed a solarhousing concept, a house designed for the warm climate in the Middle East andwith large quantities of solar panels installed. The cooling system for the house was designed in an earlier report, the purpose of this thesis is to investigate the possibility of short and long term storage of thermal energy via an underground energy storage volume.Two different designs of the storage and three different filling materials have been integrated into a model to simulate different cases. The first design consisted of pipes installed in the ground, without insulation. The second design consisted of an insulated concrete box installed to prevent thermal energy from the surrounding soil to flow towards the lower temperature regions within the storage. The three different filling materials were dry saudi sand, water saturated saudi sand and the filling material used by the client for energy storage in Sweden.The results from the simulations show that neither of the designs, regardless of the filling material, managed to extract enough thermal energy from the house to the ground to uphold the demands of indoor climate.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

We are soldiers, not policemen.Denna uppsats rör det vakuum som ofta uppstår när en regim faller samman på grund av krig, och dess ordningsmakt upplöses, eller av annat skäl inte förmår upprätta ordningen. Ofta inträffar plundring och upplopp i det ?polisiära? tomrum som inträffar från det att den tidigare regimens ordningsmakt drar sig undan, till dess att en ny poliskår träder in och bör-jar återupprätta lag och ordning. Av olika skäl frånsäger sig den intervenerande makten inte sällan arbetsuppgifter av mer ?polisiär? natur, alltifrån att bevaka samhällsviktiga byggnader till att dirigera trafik.I stor utsträckning följde kriget i Irak våren 2003 detta mönster från tidigare konflikter; ordningsmakten drog sig undan, plundring utbröt och koalitionen, bestående främst av USA och Storbritannien, nekade inledningsvis till att det var deras uppgift att ingripa mot laglösheten.

The rising demand for electricity and heat raises a big challange for the society and engineers. Many products have been introduced to the market to supply more energy to the energy systems. Absolicon AB is a Swedish company that develops and markets a combined heat and power generating product. The product, Absolicon X10, uses a parabolic trough to concentrate the radiation of the sun onto a receiver. The receiveris equipped with mono crystalline solar cells and is cooled by a circulating liquid media.

ABB I-R Waterjet Systems combines the robotics and motion expertise of ABB Flexible Automation with high-pressure intensifier/pumping technology from Ingersoll-Rand to provide and continue to develop innovative waterjet cutting systems for global markets. The purpose of this assignment is to develop a process water purifier. The purifier should be applicable as an option to ABB I-R?s production cell Cutting-Box. At first hand the process water should be purified well enough to let out in the municipal sewage system, but the ultimate solution is purifying the process water to the range that recycling is possible.

Biogas is a gaseous fuel, rich in methane, produced through a biological route in an anaerobic digester. A gas engine generates combined heat and power, which can be used at the farm to reduce energy cost. The process also generates a digestate, with better utilization of nutrient compared to cattle manure. The aim of this study is to analyze the profitability of a farm-scale biogas plant for combined heat and power (CHP) at Wapnö. Wapnö is an agriculture company located in the southern part of Sweden.

This thesis is a feasibility study into how Fresenius Kabi may rationalize their destruction process in regards to cost, recycling, and work environment. The two main objectives are to identify scrap flows and the possibility to improve or replace the equipment that is now carrying out the physical scrapping. The flow has been visualized by a flow chart of the material and communication. A chart of the problem established to visualize where improvements are necessary. Based on the problems proposals are presented on how to improve the flow thru the plant.During analyze of the physical scrapping equipment it was also necessary to take a deeper look at how they are carrying out there work today, how does the procedure look like, working environment and where are the weaknesses.