Car seats for smaller children, offers very good protection incase of a collision. Unfortunately for the parents? sake , these car seats is heavy to handle outside the car. For example back and forth home and short errands around town. In other words, all those times when you decide to just take out the car seat and carry it instead of place the baby in a baby carrier.

We are heading towards a huge switch of how energy is produced with fossil fuels being replaced by renewable energy sources. It is not difficult to replace the energy you use in the house and there is no need for futuristic technology. There are already many established products on the market such as high efficiency vacuum solar collectors, heat pumps & small wind power stations that can supply the energy being used in a house. The company Sol & Energiteknik SE AB in Huskvarna has many different products which can reduce the need for an outside energy distributor. An average house in Sweden uses 15 000 kWh for heating, 5000 kWh for tap water and 5000 kWh for electricity.

Fermented liquid feed is well known for its health promoting effects on piglets. High levels of lactic acid are desired in the feed together with low levels of acetic acid and certain biogenic amines. Limits for acetic acid have been suggested to be 30-40 mmol/kg to avoid a decreased palatability of the feed; however, few studies have been performed. The purpose of this trial was therefore to examine which levels of lactic acid and acetic acid that can be accepted in a fermented feed without affecting the feed intake and thus the weight gain of the pig. A total of 60 pigs (Yorkshire/ Hampshire) were used in a trial during two weeks, between 9-11 weeks of age.

AbstractElectricity consumption is a globally increasing problem caused by the high share of electricity produced in coal power plants. These contribute to high carbon emissions when only about 1/3 of the heat generate electricity and the remaining 2/3 of the heat cools off. Combined heat and power plants (CHP) have high efficiency because they use the residual heat for domestic heating. The CHP plant often use fuels from renewable resources, giving them a lower carbon footprint, but are also depending on the heat demand. If electric powered products such as drying cabinets convert to heat powered products more environmentally friendly electricity will be produced by CHP plants, which can supplant electricity, produced from coal power plants and reduce carbon emissions.

The municipality, of Gatukontoret in Local government of Borås has in the long run, a required need to look after the current heating devices (the gas production plant) in sewage treatment plant, called Gässlösa. The practical work of the examination is about, trying to find a better way to take care of the current heat recovery. That may be one way or another, rather easy to implement in the existent construction.Through the work to increase the efficiency of the gas engine, implement of some external cooling system by heating exchange device. That gives an opportunity to heat (primary) the digester, (but even all internal public areas) with its own superfluous heating.The report shows that if the management group may invest 422 704 crown to implement a heat exchanging device, it gives more space to reduce the need to buy expensive external energy. Gatukontoret´s pay off time, for buying machines, is 20 years, with reservation to calculate with 4 percent internal interest, leads to the yearly mount of 31103 crowns.If Gässlösa increases the gas engine time in (effective) duty approximately (correspondingly) 48 hours a month the entire investment will generate a profit in January in year seven after the implementations.

Stockholms vattenskärning AB in Kungsängen has through the acquisition of a company begun to design and produce aircraft heaters whose origin is early 1970s which follows a high inefficiency in terms of energy consumption and size.The aircraft heater, which is sold worldwide, serves its purpose for customer satisfaction and has done so ever since it was developed in the 70s.Stockholms vattenskärning AB is now investigating the possibility in making the aircraft heaters more efficient, both in terms of energy consumption but also on a more efficient design with the belief that it would lead them to an edge in the market. The aircraft heater consists of several main components whose function altogether is to keep passenger aircrafts warm while they are on the ground.This project has been limited to the further development of the heat exchanger package which accounts for the conversion of the hot medium to the fresh air being carried in to the aircraft cabin. Work has been divided into different phases in order to create a better understanding of the project range and to make it easier to divide the various elements in the time available, 10 weeks. These phases are literature review, situation analysis, concept generation, CAD, concept comparison and writing reports.After the initial literature review was made, a fundamental theory was written which is essential in understanding the remaining parts of the project.With the theoretical part as support, measurements and calculations were made on the current heat exchange package in a situation analysis to ensure its operation and efficiency.In the concept generation phase, the collected facts from the literature review was used as the basis for creating a matrix. The purpose of the matrix was to indicate the two most suitable types of heat exchangers to develop four new concepts out of.In the CAD phase the four concepts was drawn up and then described with text and images.The last phase is the concept comparison where a concept selection matrix is used to function as a decision basis for further production at Stockholms vattenskärning AB. The four concepts have been developed based on the current heat exchanger and is gradually changed into a design of a cross-flow heat exchanger constructed out of stainless sections. The purpose of this is to have gradual upgrading of the heat exchanger as an option, in order not to saturate the market..

This report treats whether it is viable to invest in solar heating to heat the therapy pool at Östersunds Rehabcentrum. The rehab center is owned by the county council of Jämtland and is located on Solliden in Östersund city. The solar heating where supposed to be a complement to the district heating that was heating the pool in the current situation. Later, it however showed that this was not the case. The pool is currently being heated by a radiator circuit that is being heated by the district heating.

In cooperate with Asko Cylinda we have developed a new heat system too short the process time and reduce the energy consume in a dishwasher and still have it too be a class AAA. The environment and quality is important for the company too still be the number one on the market, If they want too keep that position the product developed of new innovations will be very important. The systems we have developed are more effective and reduce energy up too 25 %. The process time is reduced too less than two hours, from the today two and half-hour. The solutions are too heat up the rinse water and the dishwater at the same time, with a new heating system and it make are solutions unique and effective. Its good for the dish and the environment.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

Peat litter has been used in animal houses for a long time. Because of its good ability to absorb liquid and nutrients from the manure it can create a dry surface for animals and a valuable manure product. Through changes in agricultural practises the use of peat litter has diminished and is to a great extent replaced by straw, sawdust and cutter shavings although Sweden is rich in peat-findings. The aim of this work was to summarize the presented knowledge about the used of peat litter, techniques, advantages and disadvantages and to compare with other commonly used litter materials. Articles on peat litter have been searched for in magazines, databases and books at SLU library. Visits to peat industries, interviews with peat producers and with peat researchers contributed to the material. Peat is not a uniformly material.

Clostridium difficile is a pathogen for both humans and animals and is often associated with antibiotic-associated diarrhea. Recently, several human cases of C. difficile-infection with increased mortality and morbidity have been reported. In studies performed in different countries C. difficile has been found in meat.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.

The district heating load is seasonally dependent, with a low load during periods of high ambient temperature. Thermal energy storage (TES) has the potential to shift heating loads from winter to summer, thus reducing cost and environmental impact of District Heat production. In this study, a concept of high temperature borehole thermal energy storage (HT-BTES) together with a pellet heating plant for temperature boost, is presented and evaluated by its technical limitations, its ability to supply heat, its function within the district heating system, as well as its environmental impact and economic viability in Gothenburg, Sweden, a city with access to high quantities of waste heat.The concept has proven potentially environmentally friendly and potentially profitable if its design is balanced to achieve a good enough supply temperature from the HT-BTES. The size of the heat storage, the distance between boreholes and low borehole thermal resistance are key parameters to achieve high temperature. Profitability increases if a location with lower temperature demand, as well as risk of future shortage of supply, can be met.

This report was performed in order to evaluate a new technological measure and focuses generally on a heat pump system to a HWC-washing machine. The client is Asko Appliances AB, a company well known for its environmentally friendly products. The goal of this study was to improve the energy efficiency of a washing machine by combining a heat pump device to the heater of the wash water, in order to reduce the energy consumed for heating the water. Besides reducing the energy consumption in heating the water, the washing machine was required to meet low noise and short operating time specifications. For that purpose, nine trials in three test series have been carried out.

This study is a part of a Swedish research and development project that is about heat-treated wood and is led by the Swedish University of Agricultural Sciences and Luleå University of Technology. Products that are heat-treated already exists on the market, foremost the Finnish brand ThermoWood®, bur the project group want to find out if it would be possible to start a Swedish production with somewhat different applications than what is common today. The heat-treated wood has many attributes that have changed in the heating process. It becomes more biologically durable, it gains stability in form and dimensions and it becomes darker and looses several unwanted extractives such as resin. Disadvantages that can be mentioned are that the wood becomes fragile and the strength properties changes. My main purpose with this study is to look into customer involvement in the early phase of product development. I also want to find out if the customers I interview think that the product is worth working with, which means start a Swedish production.