When grains of wheat and rye are conventionally milled, large quantities of bran classified as by-products are left and are mainly used for animal feed. Bran is a complex material composed of the aleurone layer, nucellar epidermis, a seed coat, a fruit coat and a small proportion of the germ and endosperm depending on extraction rate. The bran fraction consists of approximately 40-50 % dietary fibre which can contribute to increase the nutritional quality of human cereal food. It would also be valuable for the food industry to convert by-products as bran to products with higher commercial values. The aim of this thesis was to analyse the content and composition of dietary fibre of heat treated wheat and rye bran according to the Uppsala method with some modifications in order to analyse soluble and insoluble dietary fibre separately. Half of the bran samples were precooked, dried and roasted and the other half dried and roasted (uncooked).

This pre-study investigates the possibility of U-value measurements through an acoustic method. A hypothesis about an acoustic model built on acoustic theories combined with U-value theories is presented to answer the questions: ? Can U-value theory be combined with acoustic theories? ? Can the coefficient of heat be affirmed trough an acoustic measurement? The idea for this dissertation begun with a logical idea in mathematical similarity, between the coefficient of heat transmission units and sound intensity units. The U-value theory is based on assumptions such as initial resistance for inner walls and initial resistance for outer walls. The resistance in the material is interpreted through sound intensity theory. The argument is built upon mass law theory, which means if the frequency or thickness of the material layer doubles it implies an increase of sound reduction by 6 dB.

The heating of companies premises is today functional with electrical heating and heating offossil fuel. The energy cost for these kinds of heating in buildings has heavily increased duringthe last years and the influence on the environment has become more visual. This leads to thatenterprises today become more anxious to render energy more effective and find alternativesolutions to their ancient heating systems. This is something that Skandinaviska kraftprodukterAB in Halmstad has become aware of.The purpose with this examination is to find the most cost-efficient and environmental measuresfor the office and workshop premises of SKP AB. Where one of the bigger things is to find agood alternative for their current oil furnace, which was heating the workshop.

This thesis has identified and studied measures to allow for reduced use of electricity in a waste incineration plant in western Sweden. The energy extracted from the waste at the powerplant is utilized and sold in form of electricity and heat. Technical and environmentally the combined heat and power plant is by today's standards among the leading waste incineration plants in the world. The owners are constantly striving to improve the efficiency of the waste incineration plant. They have seen the opportunities for savings in reducing internal usage of electricity.

Heat is distributed to the district heating customers through pipes with water as a heat carrier. The district heating system is complex. To decide what is leakages from the district heating net versus what is the water consumption of the plant, is difficult. Therefore, the purpose of this master thesis is to establish a model where the district heating net?s leakages but also the water consumption of the plant can be followed daily. The project is performed at Vattenfall´s district heating power plant in Uppsala. Information is gathered through discussions, drawings of the plant and guided tours of the plant.

The report comprises two separate parts:part 1:  Temperature needs for district heating in the paint shop for axles in building 210part 2:  Energy and low temperature waste heat solutions in heating and cooling systems for   building 64 with surroundingsThe paint shop for axles in part 1 has air quality requirements in places for coating of axles. Toachieve desired air properties there are different process ventilation systems, which consist ofventilation coils for heating and cooling, plus air humidifier. The ventilations coils for heating usedistrict heating. Today the ventilation coils use water of 100°C to achieve necessary air demands inthe coating boxes. This part of the report investigates whether the existing system would achievethe air requirements with a water temperature of 75°C instead of 100°C in the ventilation coilsduring the coldest parts of the year.

This thesis is about a part of the marquetrytechnique, scorching. Scorching is made by heating up something, put a veneer into the heated substance and make a controlled burning. This technique is old but still used today and have according to me great potential for development. In my work I wanted to give the scorching greater room then I earlier have seen. I wanted the scorching to be the dominant ingredient for a decorative element in a piece of furniture or an interior.

Volvo Construction Equipment is a world leading company in construction machinery. Tomaintain the best products, development is prioritized. The master thesis regards sound reductionof the hydraulic system on a wheel loader. The background to the master thesis is asimulation made on the hydraulic system, performed autumn 2005. The result of the simulationshows that the energy of the pressure ripple is reduced when the paralleled hydraulicpumps are phase shifted and reduces each others pump pulsations.

Geothermal energy can be extracted from an aquifer, where the groundwater is used as heatexchange medium while heat and cold are stored in the surrounding material in the aquiferand to some extent in the groundwater. Application of aquifer storage for the use ofgeothermal energy is mainly used in large scale facilities and is limited to sites with suitableaquifers in the form of ridges, sandstone and limestone aquifers.Löwenströmska hospital in the municipality of Upplands Väsby, north of Stockholm, islocated nearby the northern part of the Stockholm esker. This means that it can be profitableand environmentally beneficial for the hospital to examine the possibilities of aquifer storagein the esker material next to its property.The purpose of this master thesis has been to investigate if geothermal energy storage with aseasonal storage of heat and cold can be applied within Löwenströmska hospital?s propertyarea using groundwater modeling. A hydraulic groundwater model was constructed inMODFLOW based on a simplified conceptual model of the groundwater system.

This master thesis was carried out for Saab Avitronics, a business unit of Saab ABactive in electronic systems for military aircrafts. Reliability and weight are of crucialimportance in this environment. To improve reliability and lower the weight graphitemay be used for electronics cooling. Graphite is an anisotropic material and hasthereof high thermal conductivity in two directions (in-plane) and a relatively lowconductivity in the third direction (through thickness).The purpose of this thesis was to investigate if graphite is an adequate thermalconductor to use in PCB carriers. The carriers support and cool the PCB by divertingthe heat dissipation from the PCB components to the edge.

This dissertation is performed at the request of Lagafors AB who develops and manufactures stationery and mobile hygiene solutions for companies in the food- processing industry. The objective of this dissertation is to develop and construct a new, cost efficient cleaning station based on an innovative technology.The technique is based on serially connected dosing pumps which allow the customer to work with concentrated detergents. This leads to serious reduction in the clients use expenses. Two units have been developed with this technique, one that is stationary and one that is mobile.The dissertation has led to good results which resulted in the sale of the first stationary unit of the Lagafors CPU before the end of this dissertation. .

Tylö AB is the leading manufactor of sauna cabins in Europe, but there is a lack of a sauna lightning produced by Tylö. The project of developing a new sauna lightning series was assigned two students at the developmentengineering program at Halmstad University. The main problem with lightning in the sauna is the heat and security aspect. The selection fell on LED technology as the lightning source, thanks to its small measures and low heat emission. The work of constructing of a lightning armature which the capability of cooling down the LED lightning was carried out during autumn ?06 and spring ?07.

Tylö AB is the leading manufactor of sauna cabins in Europe, but there is a lackof a sauna lightning produced by Tylö. The project of developing a new saunalightning series was assigned two students at the developmentengineeringprogram at Halmstad University. The main problem with lightning in the saunais the heat and security aspect. The selection fell on LED technology as thelightning source, thanks to its small measures and low heat emission.The work of constructing of a lightning armature which the capability of coolingdown the LED lightning was carried out during autumn ?06 and spring ?07.

AbstractClimate and environmental issues are of paramount importance. Researchers agreethat we must all contribute to a reduction of gases that contribute to climatechange. Energy consumption must decrease within all sectors and the promotionof renewable sources of energy must be introduced.Each sector should aspire to decrease its energy consumption. Energyconsumption is strongly linked to waste gases that contribute to climate change.Passive houses are a part of the construction industry's methods to attain energyconservation.Passive houses are derived from low energy houses and super insulated houses. Apassive house is intended to obtain heat from the inhabitants and through theiractivities.

sustainable development by reducing the energy use by EU:s directive of energy efficiency and the UN Convention. The second purpose is to present the technical solutions regarding ventilation and heating system that is being used in passive houses. This was done using 8 passive houses, 4 germany and 4 swedish passive houses. Even the international and Swedish system requirements for passive houses have been addressed in this project. The goal was also to explain how and why the mechanical system in passive houses has developed to the technology used today.