Water Hardness indicates the concentration of calcium and magnesium ions in water. Water with high concentrations of these ions is described as hard water and water with low concentrations is described as soft water. Water that is too hard or too soft can lead to technical and economical problems. In collaboration with Midvatten AB, groundwater Hardness in the Badelunda esker between Leksand and Avesta has been mapped, and an attempt has been made to explain the variations. For this purpose, different GIS programs, such as ArcView, ArcInfo, IDIRISI, and one geochemical modelling program, PHREEQC, has been used.

In my thesis I have sand blasted different type of woods - ring-porous and diffuseporous deciduous tree species and conifers - to show different results depending on the species, the direction of the grain and the effects of surface treatment of a blasted surface.The results of my tests were sometimes unexpected, such as that the sand from blasting almost completely disappeared, that all wood surfaces after blasting exhibited a much lighter or paler surface than before and that the diffuse-porous tree species showed differences in Hardness between the beginning and end of annual rings.By creating a library of different kinds of wood and sandblasted surface treatment, I have created a reference bank that I will be able to use me in the manufacturing of interiors, furniture and other objects..

Nowadays naval units are participating in international missions, where new and in many cases tougher conditions will affect their propulsion. This essay deals with some of the now developed nanostructure coatings and gives a presentation of how the coatings could function on some exposed parts of the naval powertrain. The essay investigates the possibility that the coatings can be used as a protective layer that will reduce or prevent wear on selected parts of the naval powertrains. As a basis for the essay, nanotechnology is described, as well as different reasons that wear occurs and application techniques for coatings The conclusion is that nanostructured coatings can be applied and provide a much better result on Hardness and wear resistance as of naval powertrains compared to micro-structural coatings, both for manufacturing and renovation. The essay presents a few examples of the military utility of the nanostructure coatings as well as suggestions for further research..

Hårdgörning av trä syftar till att göra materialet hårdare. Detta går att åstadkomma genom komprimering, det komprimerade materialet tenderar dock att återgå mot sin ursprungsform då materialet utsätts för fukt om ingen låsning sker. Låsningen kan ske mekaniskt i en treskiktskonstruktion som motverkar träets fuktrörelser. Dessa skivor har dock visat sig vara instabila och tidigare försök har uppvisat deformationer i form av kupning. Denna undersökning syftar till att utreda förutsättningarna för att använda komprimerad asp samt att ta fram underlag för framtagning av en kommersiell produkt.Praktiska tester har genomförts för att studera hårdhet, återfjädring och densitet hos det komprimerade virket.

Weathering on rocks is an important component of the world?s geomorphology. One way to measure weathering on rocks is to analyse rock Hardness. This is a study conducted in the northern hemisphere on granite rocks in Uppsala, Sweden. A Schmidt hammer is used to create a correlation analysis between the aspects on three glacial erratic boulders and rock weathering.

Background Research concerning footing and its contribution to injuries has been conducted primarily in racing Thoroughbreds. Studies in UK and Japan indicate that some specific factors could be responsible for an increase in performance-associated injuries. Researchers in Sweden have performed studies on Standardbred trotters. More research is needed to be done on equestrian sports since requirements on footing are not exactly the same in riding and trotting horses. The lack of scientific evidence on the construction of equestrian surfaces has lead to anecdotal validation of designs.

Nowadays naval units are participating in international missions, where new and in many cases tougher conditions will affect their propulsion. This essay deals with some of the now developed nanostructure coatings and gives a presentation of how the coatings could function on some exposed parts of the naval powertrain. The essay investigates the possibility that the coatings can be used as a protective layer that will reduce or prevent wear on selected parts of the naval powertrains. As a basis for the essay, nanotechnology is described, as well as different reasons that wear occurs and application techniques for coatings The conclusion is that nanostructured coatings can be applied and provide a much better result on Hardness and wear resistance as of naval powertrains compared to micro-structural coatings, both for manufacturing and renovation. The essay presents a few examples of the military utility of the nanostructure coatings as well as suggestions for further research..

When driving hard and cornering on a circuit good control of a car?s roll is desired, so the car reaches steady state quickly but yet in a controlled fashion. This control is mainly given by the combination of the cars springs, shock absorbers and anti-roll bars.The aim of this report is to investigate, analyze and measure a Porsche Boxster?s turn in behaviour and roll dynamics as well as with the aid of simulation results give suggestions for improvement of the previous mentioned combination.Two different simulations were made, one based on a simpler model that was based on an evolved version of the bicycle model in Matlab and one was more advanced model in the simulation software rFactor. Measurements of the real car was made using a GPS-based measurement system.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing Hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

The Sheep is the oldest livestock, and has been in Sweden for 4-5000 years. Thanks to that you can obtain skin, as well wool and meat. Therefore it was an important animal. Sheep production has increased, strongly lately due to the pasture support. The purpose of this paper is to find out what kind of different EU-subsidies you can get and to compare the subsidies in Öland and the main land. Sheeps are very good conservationist with grass, bushes and herbs, because of different grazing lands Hardness and growth is it important to control the pasturage strain. A good way to regulate this is to have different enclosed pasture to switch between. I have been studying the different EU-subsidies.

An investigation of the heat impact of laser cutting on the material properties when producing tensile and impact test specimens of different steel types of varying thickness has been performed. The purpose of the thesis project was to provide recommendations regarding how much material that needs to be milled from the laser cut edge before tensile and impact tests. The study has been performed partly by investigating the test specimens by heat camera when the specimens were cut in the laser cutting line and partly by performing Hardness tests, investigation by microscopy, and tolerance and roughness measurements and tensile tests of the laser cut material and material produced in the traditional multi operation machine. The results show that the heat affected zone in the thicker materials is greater than previously thought of, and that the currently used recommendation has to be adjusted. The study clearly shows that the thicker the material, the greater the heat affected zone, independently of the steel type, since the thicker material takes longer time to cut.

Vid användande av polymerer och elastomerer i konstruktioner, lämnar leverantörer oftast endast materialparametrar i form av ett hårdhetstal. De vanligaste provningsmetoderna för hårdhetsmätning av polymerer och elastomerer är Shore samt IRHD (International Rubber Hardness Degree). Hårdhetstalen som erhålls är svåra att använda i Finita Elementanalyser, då de ej direkt kan översättas till mer lätthanterliga storheter. Syftet med examensarbetet är att utveckla en metod för att omvandla hårdhetstal till användbara Finita Elementstorheter. Det finns flera olika metoder för hårdhetsmätning inom Shore och IRHD.Arbetet begränsades dock till att enbart täcka en metod för Shore samt två metoder för IRHD.

Public concern about the release of toxic compounds from wood-based products drives legislation towards enforcing industries to find and use more sustainable solutions for wood treatment. Plant oils are good alternatives to treat wood, minimizing or even neutralizing the impact on the environment. Wood modification with epoxidised linseed oil (ELO) and acetic acid as catalyst has proven a suitable method to impregnate and protect wood. However, the mixture presents a serious inconvenience because of the quick polymerization of the ingredients that limits its practical application. Therefore, this study was designed to evaluate an alternative method using a two-step process which bypassed the problem above.

The surface finishing technique called black oxidation is currently being used on thetool holders made of low alloyed tool steel produced by Sandvik Coromant. Blackoxidation isn?t considered a sufficient technique because it doesn?t make the toolholders look like the quality products that they actually are. The reasoning behind thisis that the tool holders can show signs of corrosion after prolonged storing times orin countries with high humidity and temperature. The corrosion doesn?t decrease thetool holders performance, but the customers might believe otherwise.

This thesis work is made by Torbjörn Johansson on Karlstad University for Uddeholms AB. The assignment in this thesis work was to investigate tough cutting in three different tool steels: Vanadis 4 Extra, Vancron 40 and Sverker 21. The research was to compare the wear of the tool after cutting in each one of the tool steel alloys. The research was also made to see if the tool cutting in Vancron 40 has a better wear than the tool cutting in Vanadis 4 Extra and also compare the results with Sverker 21. All three of these alloys are a part of Uddeholms AB:s range of products, and is used in applications like forming tools and knife tools. Vancron 40 is a powder steel with a very good combination of mechanical properties like ductility, adhesive strength and Hardness.