Med detta examensarbete vill vi belysa problematiken runt tredimensionell fastighetsbildning. Som objekt har vi använt oss av ett bergrum på Liljeholmskajen i Stockholm..

I have in my thesis, examined the possibilities in terms of energy for a condominium association.To have an effective and good energy is becoming increasingly important with today's rising electric and oil prices. In my thesis I have used the condominium association Kärralyckan, which is situated in Falkenberg. The buildings at Kärralyckan are built in the mid-1970s, and are heated by electric radiators. The tap water is heated by an electric boiler.Based on that calculation I can show the various energyststem. The different solutions have been developed by contact manufacturers and installers through phone calls and e-mail.According to the results shows that geothermal heating has been a great solution for Kärralyckan.

The main purpose with the project has been to approximate the magnitude of the pollution transport from the actual road surfaces and to get an approximation of the possibility to collect the pollutants to reduce the load to the water and improve the water quality.The quantity of pollution transport from the most trafficated roads areas in Örebro city has been calculated. Roads whith a traffic exceeding 10 000 vehicle/day. The study has been done with the calculation tool StormTac. Through analysis of traffic loads and road surface, which together with a different kinds of parameters gives an approximation of the pollutant transport.The calculation has included some metals and other substances in the stormwater and has also included the present of suspended solids. Included the overall study, some smaller areas has also been calculated for the possibility to remove pollutants.The work also includes calculation for three different areas for stormwater treatment.

This masters thesis concerns a modeling project performed at Volvo Technology in Gothenburg, Sweden. The main purpose of the project has been to develop a physical model of the climate in construction vehicles that later on can be used in the development of an electronic climate controller. The focus of the work has been on one type of wheel loader and one type of excavator. The temperature inside the compartment has been set equal to the notion climate. With physical theories about air flow and heat transfer in respect, relations between the components in the climate unit and the compartment has been calculated.

This report is about the impact climate change has on the water and sewage systems in general, and the situation in the municipality of Karlstad in particular. Which vulnerabilities are linked to water and sewage systems with regard to climate change and extreme weather situations, what are the possibilities to adapt the system to this and what significance does climate adaptation of the water and sewage systems have in relation to sustainable development?To answer these questions I have studied literature on the subject and interviewed several people who work with these types of questions. The answers I have received state that there are a multitude of vulnerabilities linked to the water- and sewage systems, but that there are also many strong interests which strive to take measures and adapt to a changed climate. I have also come to the conclusion that the starting points and views of the possibilities to act differs between the people that I have interviewed, but that theses problems are built into the concept of democracy..

This Master degree project has been performed at the Braviken paper mill on papermachine 53 (PM53) which produces newsprint paper. The current economic situationhas contributed to declining demand for newsprint, which means it is extra important tobe competitive by high energy efficiency. Particularly as energy prices are expected torise when the economic growth returns.One way to increase energy efficiency is by reducing the water use in paper and pulpmills and consequently save energy through reduced heating of water. The thesis's maintask is to evaluate whether a water purification plant (microflotation plant) forpurification of process water in PM 53 is profitable. The microflotation plant enablesreuse of warm process water instead of losing the energy to receiving waters.

When stormwater occurs near human activity the water gets polluted. The purity and composition vary widely depending on the types of activities in the area, the type of surface the water comes in contact with, precipitation and many more parameters. It has long been known that stormwater quality can affect both human health and the environment as stormwater is a major contributor to pollution of receiving waters.A human activity that has an impact on the environment in several different ways is traffic and stormwater is no exception. Airborne gases that react with precipitation, oil leaks and fuel systems that drops down on the ground, metals from brake linings and rubber particles from tire wear are some of the aspects you have to take into account when categorizing the relationship between traffic and polluted stormwater.In this project, stormwater samples from a parking lot in Halmstad, Sweden were collected and analyzed with an atomic spectrophotometer. The presence and relationship between copper, cadmium and zinc with different rainfall parameters have been studied.

Lake lowering in sulphide-rich areas is currently a major environmental impact for surface water. This study focuses on whether there is a relationship between a gradient of lake lowering and surface water impacts in areas of sulphide-rich sediments, in order to better understand their contribution of heavy metals and sulfuric acid. Also, is it a reasonable method to use the reduced lake area in order to quantify the gradient? The survey was conducted by collecting water samples from reference lakes and lowered lakes from south to north in coastal areas within the county of Västerbotten. Water samples were then analyzed for TOC, pH, conductivity, anions, base cations, alkalinity, acidity, sulfate, Al, Cd, Fe, Mn, Cu, Zn and Pb.

ICA vill utveckla sitt miljöarbete i vattenfrågor. Denna rapport syftar till att öka medvetenheten hos ICA om verksamhetens miljöpåverkan genom att analysera vattenfotavtrycket ? vanligen kallat Water Footprint ? för ett livsmedel. Vattenfotavtryck är ett verktyg inom miljösystemanalys som används för att kartlägga sambandet mellan produktion och konsumtion av produkter och vattenanvändning. Studien visade att vattenfotavtrycken är ungefär 14 500 liter/kg och 16 500 liter/kg för svensk respektive irländsk nötfärs.

Amongst the published literature researching wet cleaning of paper there is a limited amount of studies conducted researching the method simmering water treatment. There are even less studies conducted on how simmering water affects the paper being treated when used as a cleaning method. Despite the limited research, there are literary reviews describing the method and suggesting it as an alternative for conservation of paper with iron-gall ink. The following study will therefore be examining, the somewhat unusual method, simmering water treatment, and comparing it to one of the more common wet cleaning methods: immersion washing. This is done to compare how the different temperatures of the water affect the paper. The types of paper used in this study consists of three dyed and four undyed papers. All of the papers are new, apart from one sample originating from 1847.

An increasing number of heat pump producers have developed heat pumps that can be connected to solar panels. In this thesis we have examined the possibilities of connecting solar panels to existing ground source- and geothermal heat pumps that has not been adapted to solar panels. During the work process, a prototype plant has been built to compare our theory with the practical results and with our designed sizing tool. The work has rendered in knowledge that will be used to build a sun module that can be easily connect to the existing heat pump system. The existing heat pump, our test plant, has been supplemented by an advanced storage tank used to allow different operating modes.

An increased number of participants in the construction industry is asking for accompanying terrain models to the project in order to get a better understanding of the field. When the desire to create buildings that fit together nicely with the surrounding area is increasing, it becomes more and more important to have a broad base of knowledge about the ground on which the building is to be erected. Terrain models are also very useful in the planning of logistics, documentation for landscape architecture projects, and billings for mass calculations.Surveys for creating terrain models can be performed with laser scanning. The advantage of laser scanning is the time-effective surveying, the detailed information as well as the ability of application in complex environments resulting in a cost-efficient project. With this in mind our thesis was defined in collaboration with the company Bjerking AB in Uppsala in order to investigate if there were any softwares suitable for terrain modeling.

Floating housing is a concept gaining ground in Sweden. The dwellings are different in many ways from traditional homes, not only regarding flotation, but also several other technologies. The purpose of this thesis is to emphasize the qualities that exist in living on water. The ambition was to present a proposal for a floating residential area located in Jönköping, containing homes of varying sizes, and to present their technologies. In order to find inspiration and solutions studies have been made on existing floating homes in Stockholm and Kalmar, focusing on their technical and functional solutions.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

The environment that surrounds us affects us all. Research has shown that we feel physically and emotionally best in natural environments with greenery or water elements. Urban environments are likely to be more stressing then natural environments. How we experience specific elements, as water, of an environment is not as much investigated. There is a need of further knowledge for us to fully understand the interplay between our senses and the environment. Human beings have always been depending on water and the search for it has characterized our deeds and doings through out evolution.