As a consequence of increasing wind power installations in the Nordic grid the last years, the need for regulating power has become larger. In the Nordic grid, regulating power is mainly provided by hydro power. One part of the regulating power is called frequency control, which ensures that the grid frequency is stable and close to 50 Hz.However, setting the turbine into frequency controlled operation may cause stress and wear of the components in the mechanical control system. Frequency controlling implies large and frequent servo forces and longer travelling distance of the sliding bearings in the Kaplan turbine.Based on one selected Kaplan turbine, Selsfors G1, measurements and MATLAB calculations have been performed in order to determine forces and movements of the linkage system. With these forces and movements as input, stresses and fatigue have been determined as well as sliding distances, bearing pressures and wear of bearings during a typical lifetime of 40 years.The results indicate that no severe wear exists on the bearings during 40 years of service.

This report summarize what have been done during the Master of Science Thesis that Klas Schjelderup has written for the company RANOTOR Utvecklings AB. The company is developing modern steam engines and this work should develop a machine to perform tests on a new type of piston seal that hopefully could be used in the future. The steam engines will be both volumetric and energy compact, around 1600hp/literof cylinder volume, and it will have a lot of practical applications.The new type of piston seal is hydrostatic lubricated which means that a fluid is separating two faces that normally is in contact. In this case pressurized water is used to separate the piston seal from the cylinder wall. RANOTOR have earlier formulated that at least the expander in the modern steam engine have to be oil-free, due to other components functionality in the closed water system.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

Phosphate is a used as a surface treatment method which is used for various purposes in the industry. In this case, phosphate coated wire is used in the processes to achieve a desirable outcome. The reason to why phosphate coated wire is used in the production process is because phosphate acts as an accumulator, where it stabilizes the lubricant on the surface of the wire. Lubrication is important because it plays a major role in the roll quality and characterizes important benefits regarding the outcome.Currently, SKF has to wash away all phosphates residues after extrusion process in an operation called tumbling. The main reason for this is simply because the surface has to be completely free from lubricants and coatings till the next step of process.

This thesis applies to a novel steam expander, one part of a steam engine system, a wobble plateengine. The piston in the expander moves axially with the outgoing rotating shaft and is locatedon a plate, why the engine type is called axial engine. When steam is applied to the plungers theplate wobbles creating a rotation on the shaft going thru the wobble plate. The steam expander issupposed to be used in exhaust gas recovery (bottoming cycle) applications and small scaleenergy production. The commissioner is Ranotor Utveckling AB.

A Swedish electronics company wants to make the cooling of one of their electronic components more efficient. They propose that a retrofit liquid cooler is the way to achieve this goal. The current air cooling has high energy cost due to the high amount of power needed to power fans and heat exchangers. Using high volumes of air for cooling also leads to noise pollution. The conversion from air to liquid cooling would possibly make the operation of the electronics more cost efficient and less noisy.The purpose of this project is to theoretically evaluate different concepts of drawing the heat generated by the electronic component in to a fluid, using numerical calculations in Matlab and FEM simulations in ANSYS.

The purpose with this thesis is to get a compilation of all the critical bolted joints of all enginesproduced at LV Motors. ABB LV Motors produces induction engines with seven shaft heights. Eachengine size exists several variants of components ex. standard shield and flange shield. Depending onwhich components the engine is equipped with arises various types of strains in the engine's parts,certain assembly ways are more favourable than other.The most critical parts in the engine from a mechanical point of view are the screw units betweenshield/stator, feet/stator and bearing cover/shield.

Denna uppsats handlade om att genom en textanalys studera hur två hälsotidskrifter, Hälsa och Må Bra, framställde ämnet kost och hälsa. Hälsoupplysningen började under 1700-talet, med skrifter och utvecklades därefter till ett allt större forum i takt med samhällsutvecklingen. I dagsläget kunde jag identifiera flertalet sätt där hälsoupplysning förekom som tex. via TV, internet, massmedia, reklamannonser, apotek, hälsokostaffärer, dagstidningar, tidskrifter, etc. Av detta urval valde jag att genom en textanalys, samt genom att hämta inspiration av några analysredskap, som metaforer, intertextualitet samt modalitet, studera hur tidskrifterna genom sina artiklar valde att framställa kost och hälsa.

This thesis work has been performed on request by SWT (Scandinavia WeldTech AB). SWT manufactures, develop and sell ready to assemble building systems for concrete rafter beam applications. The beams in this system consist of a u-beam that is welded to a flange. To be able to fill the beams with concrete there is holes in the beams top end. The holes are made in a ?punching machine?.  These holes are cut out and the remaining steel piece is bent down in the u-beam.

The calf extrator?s function has been studied, through measuring traction and how this varies in different situations, in comparison with corresponding manual traction situations. This was done against the background that excessive force at assisted calvings at dystocia can mean life threatening damages on the calf such as grave acidosis, vertebral fractures, femur fractures and rib fractures. The calf extractor has earlier been measured to pull with greater force than the established maximum force of ?two strong men?.