This report was written by Sofia Ericson and describes the degree thesis with the title: ?Connections between the growing site of bio fuel, the chemical composition of bio fuel ash and the deposit growth in a bio fuel fired boiler.? The purpose of this degree thesis was to avoid melted deposit growth in the bio fuel fired boiler at ENA Kraft in Enköping. Potassium and sodium are known to lower the melting point of bio fuel ashes and are therefore not wanted in the trees in higher amounts than necessary for the growth. Silicon is also known to be important for the deposit growth but it is not possible to say in general if higher or lower contents of silicon is better. The relation between silicon and other chemical substances is more important than the total amount of silicon.

The aim of this master thesis was to create a dynamic model for the processes in a solid fuel boiler of the moving grate type. Another aim with the model was to keep it as simple as possible but still able to catch the dynamics of the processes in the bedplate of the boiler. The creation of the model had its origin from drying and combustion equations used in earlier modeling work of boilers. The represented model has been used to simulate different kinds of disturbances in a boiler and different ways to control the boiler. These tests show that controlling a number of parameters in the bed of the boiler is an effective way to keep the grate stable during disturbances.

Intresset för biobränsleproducerad energi har ökat i takt med att kunderna blivit mer miljömedvetna. På grund av detta har efterfrågan på briketter ökat samtidigt som träindustrin har haft det svårt i en sviktande konjunktur. Därför har ett examensarbete utförts i samarbete med E.ON Värme Sverige AB där undersökningar på bränslebyte i pannor avsedda för torra bränslen till fuktigare, stamvedflis har utfört.För denna undersökning har begränsningar införts på övre och undre effekt i form av uppehållstid och slutförbränningstemperatur. Intervallen är enbart beräknade på stamvedflis med 30 och 40 % fukthalt.Undersökning visar att det går bra att elda stamvedsflis i briketteldade pannor utan att emissionerna ökar så pass mycket att villkoren för anläggningarna överskrids om lasten hålls inom vissa intervall. Det möjliga effektintervallet ökar med minskad fukthalt på bränslet.Undersökningen har visat att det är bränslets kvalitet som är den mest begränsande faktorn..

In the EU the amount of waste increased by 14 percent during the years 2000 to 2010. EU?s target to reduce waste generation runs parallel with the aim of increasing the efficiency and profitability aligned with energy recovery. In Sweden the energy recovery through incineration is increasing steadily, and 46 percent of the municipal solid waste (MSW) is treated by combustion. This report aims to examine the profitability of processing MSW into Refuse Derived Fuel (RDF) from an economic-, energy- and environmental perspective.

Emission of nitrogen oxides as well as carbon monoxides is an inevitable result of combustion. A Swedish law "Law of environmental fee for emissions of nitrogen oxides as a result of energy production" (lagen om miljöavgift på utsläpp av kväveoxider vid energiproduktion (SFS 1990:613)) controls the emission of NOx from energy production by a system of fees. The system has resulted in a strong approach toward less emissions of NOx among the energy production plants. High emission levels, today exceeding 52 mg/MJsupplied fuel, leads to costs for energy production companies. This paper examines possibilities to reduce the emissions of NOx by optimization of the SNCR-technique in a biofuel fired heat and power plant.

The project focus on combustion of softwood pellets and pellets in a 40 kW grate fire reactor at TEC-Lab. Dept Applied Physics and Electronics at Umeå University. Experiments were performed at four primary airs to fuel ratios (0.7 to 1.3), where aspects such as temperature profile, levels of gases (CO and NO), sintering-/-slagging and unburned fraction of the ashes were studied. Four different fuel loads were used for wood pellets (10, 20 and 30 kW) and one fuel load for straw (10 kW). Combustion of straw proved very difficult to ignite, and also led to other combustion-related technical problem such as slag formation due to the relatively low melting temperature-/-slag temperature of the straw.

The municipality of Enköping is presently working out a new layout plan for the town of Enköping and new residences are planned in the harbour area. Because of these plans, the municipal energy company ENA Energi may have to move its location from the harbour to another part of the city.The aim of this degree project is to investigate the possibility of building a new CHP plant in another area of Enköping. The future demand on district heating and infrastructure at the new location have been projected. A new CHP plant has been dimensioned and economic analyses concerning the project have been made.Results show that the future demand of district heating in Enköping will differ a little from the present needs. In 2030, the district heating production is expected to be c.

Luossavaara-Kiirunavaara Aktiebolag (LKAB) är en gruvdriftskoncern med järnmalmsbrytning som huvudsaklig verksamhet. En av produkterna tas fram genom att raffinera järnmalm till pellets vilket är en efterfrågad produkt vid ståltillverkning. Vid sintring av råkulor till pellets är temperaturen väsentlig för att få så hög oxidation som möjligt av magnetit till hematit och för att få rätt fasthet. För att reglera värmen bör temperaturen mätas bland råkulorna eftersom det är kulornas temperatur som är det viktiga.                                 Projektet går ut på att undersöka möjligheterna att mäta temperatur bland råkulor på gratevagnar som åker genom en pelletsugn med ett permanent mätsystem. Här ställs höga krav på mätsystemet på grund av miljö, portabilitet och drifttid.Miljöanalyser gjordes för att ta reda på vilken påfrestning ett mätsystem bör klara av. Förslag om placering av mätutrustning framtogs genom kartläggning av miljön.

LKAB har tre kulsinterverk av s k grate-kiln typ, två stycken i Kiruna samt ett i Svappavaara. I grate-kiln systemet sker torkning och förvärmning av råkulor på en bandugn (grate), vidare bränning/sintring i en roterugn (kiln) och slutligen värmeåtervinning vid kylning av pelletsen i en roterande kylare. Rosterplattorna (grateplattorna) är tillverkade av ett gjutet värmebeständigt rostfritt material. Tidigare har livslängden på dessa plattor varit ca 2,5-3 år. Under de senaste åren har dock plattorna uppvisat betydligt större slitage än tidigare, och åtgärder måste vidtas för att uppnå en godtagbar livslängd på grateplattorna.

This paper deals with the opportunities for the technique of condensation, for wood fired household heaters, on the Swedish market. In this project the condenser is preceded by a scrubber and both energy exchange and separation of unburnt particles have been studied. The facility studied is connected to a wood stove at 30 kW. The tests would show that the effect from the stove never reached above 16 kW. This might be a result of the low temperature of the water going into the stove, from the condenser. In addition to this the wood was not of highest quality and the stove could have needed some maintenance before the tests.

Det här examensarbetet går ut på att utreda vilken påverkan oljeval och inkörningsmetod har på tätning mellan kolvring och cylindervägg i en fyrtaktsmotor. Arbetet har utförts på en motorcykel av märket Honda och modellen heter CBR 954 RR årsmodell 2003. Det diskuteras dagligen i tidningar, på internet och i garage runt om i världen om vilken typ av inkörning som är effektivast för att få en motor att gå bra och hålla länge. Vissa bil- och mctillverkare har helt tagit bort sina inkörningsrekommendationer medan andra fortfarande har kvar rekommendationen att man ska köra lugnt och på låga varvtal under ett visst antal mil. Eftersom att inkörningen påverkar väldigt många parametrar så finns inte möjlighet att testa hur olika oljeval och inkörningsmetoder påverkar alla dessa parametrar.

This report summarizes the development of a calculation program estimating the profitability of converting a peak-load oil-fired boiler to pellets. To convert an oil-fired boiler to pellets a new fuel handling system must be designed. Changes also have to be made to some other components. Since there are many different techniques for transportation, storage and treatment of the fuel only the most interesting techniques from Swecos experience and interest were included in the study.The capacity of the different parts in the system was dimensioned based on the power of the boiler after conversion. To estimate prices, installed power and dimensions manufacturers and distributers were contacted.

Combustion of fossil fuels is today the dominating source of energy. During combustion,carbon dioxide is formed. The carbon dioxide accumulates in the atmosphere,which raises the global average temperature on earth through the so called greenhouseeffect. The only way to reduce the emissions of carbon dioxide from combustionin a coal fired power plant is through carbon capture and storage (CCS).Post-combustion capture is a technology to separate carbon dioxide from the uegas after the combustion for efficient transport and storage. The steady state operationof coal fired power plants with post combustion capture has already beenthoroughly investigated on a pilot scale, however much work remains to investigatethe plants dynamic operation.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.