In this thesis tests has been performed on the pull strength of screws Glued into glulam beams.The experiment is based on the already approved method whereby the diameter of the drilled holes is the same as the screw outer diameter of 1 mm or bigger. The screws strength class shall not be less than 4.6 (EN ISO 898-1:1999, 1999).The difference in the experiments that were performed where that the drilled diameter were 1 mm smaller than the outer diameter of the screw so that the screw thread was worked into the wood.In the tests the gluing where made on M8 glulam beams. The screws where drilled at and angel of 90°tangental to the fiber direction with a diameter of 7 mm. The gluing of the screws where made in three different depths and where later exposed to pulling forces. The results showed both pulling breaks and screw breaks when they reached their maximum capacity.

SummaryI have a great interest in bouzoukis and since I, during my education in guitar making, mainly have focused on building bouzoukis and other traditional folk instruments, I have chosen the bouzouki as the object of my degree project.In connection to the making of these instruments, I started to consider the construction of the bouzouki and why the bouzouki has such a characteristic sound.One of my theories is based on the fact that most bouzoukis are made with floating bridges instead of Glued pinbridges. Do these types of bridges differ from each other tonally and if so, how much and in what way?To receive answers to my questions, I have built two identical bouzoukis with different types of bridges, one with a Glued pinbridge and one with a floating bridge. I have been very precise in the making of these instruments, giving them the exact same dimensions and using material from the same piece of wood. This to make sure that the instruments should be as exactly alike as possible.After finishing the making of the bouzoukis, I arranged for a sound test where I let musicians play and listen to the instruments.

This essay examines pull-out strength of threaded rods fixed into glulam timber. The technology is intended to be used in hidden joints between glulam components. The work began with a study of literature focusing on current research within the topic, mainly to create a base of knowledge before the testing was initiated. Studies of scientific articles reveals a lack of research within this area, which makes it difficult to develop standards and calculation models for these joints. The drill holes in the tests have a diameter of 7 mm.

Lättelement located in Örnskoldsvik AB is one of Sweden's leading companies in the development of building elements in the form of roofs, walls and floors made ??out of light beams. The company has clients from Lund to Kiruna, and from Norway. This means that the elements have high standards when they have to take many different loads from wind and snow due to such wide geographic variation.The roof elements are structured so that the main body is made of light beams with an I?profile.

Idag blir det allt vanligare med träbyggnader högre än två våningar. Detta tillsammans med en modern arkitektur som ger stora öppna planlösningar ställer höga krav på bjälklagen i träbyggnader. Problematiken med långa spännvidder för bjälklag i trä är att klara kraven för svikt och nedböjning. Dessa krav måste uppfyllas för att säkerställa funktioner hos andra byggdelar och för att människor inte ska uppleva att golvet sviktar eller vibrerar på ett obehagligt sätt.Ett träbjälklag bestående av limmade balkar av sidobräder har utvecklats. Bjälklaget är utformat av balkar med I-tvärsnitt i primärriktningen och rektangulära balktvärsnitt i sekundärriktningen.

Utvecklingen av förbandsmetoder är viktigt för att utveckla konstruktionslösningar. Under det senaste decenniet har forskning på limmade förband utförts, främst på inlimning av stålstag och plattstål i limträ. Förhoppningen är att spänningen ska fördelas jämnare i förbandet och att brott ska kunna undvikas. Hypotetiskt sett skulle det kunna göra knutpunker utan synliga förband möjliga vilket även skulle gynna arkitekternas önskemål.Genom en sammanställning av tidigare forskning dras en jämförelse mellan testresultaten och en antagen knutpunkt som belastas av egentyngder och variabla laster. På så sätt kan limmets kapacitet konkretiseras.

The aim of this study was to determine a method to habituate treadmill-naive Labrador Retrievers to walk and trot on a treadmill. 17 Labradors was equipped with reflective markers Glued to the skin. Their motions were captured with six 240 Hz infra-red cameras as they walked and trotted on a treadmill three times a day for two days. Also the heart-rate was recorded. We then used QTM and custom built software to analyze the measurements.

Lattelement AB in Ornskoldsvik is one of the leading companies in Sweden in composite elements in walls, floors and roofs in particular. The company supplies elements to buildings located with a wide geographical variation, which means that the products are subjected to very different climate with regard to snow, wind and humidity. This places high demands and requires the elements to withstand large variable loads.The elements are made of lightweight beams with flanges of structural timber and beam webs made of OSB. These are bound together by nogging pieces with the same kind of structure. On top of the beams a nailed and Glued plywood is added to absorb compressive forces and on the underside of the element a sheet of steel is added for tensile absorption.These elements are then attached to the building framework in different ways depending on the particular element height, loads and the structual supporting material of the frame work.

In this thesis a concept for floor hatches for foam pits has been developed. Since there is an existing solution that is powered by hydraulics and is expensive, the goal was to develop a cheaper solution, as simple as possible.A number of different concepts were developed and evaluated. A concept with five sections that are pulled to the side and stacked on each other was chosen as it was thought to have the lowest risk of crush injuries and to be easiest to manage and control. In the opening behind the foam mattress a lifting table is placed to regulate the height of the stacked sections.To be allowed to be installed in the floor of sports halls the sections must be dimensioned according to the construction standards for these types of buildings. Different dimensions of beams in steel and wood materials were evaluated and of those, who lived up to the requirements of the standard, a concept was chosen.

The exclusion of visually impaired from the information flow presented to us through signs was what led me into this project. With a growing amount of information being presented to us on signs and digital information surface the need of communicating this information in a way that could be read by visually impaired is evident. Looking into different ways of communication, my goal was to create something that filled the need of the visually impaired without branding them as disabled. Having a close relative with bad eyesight is became evident on how much it limited her in her everyday life, not being able to navigate herself without the support of her husband. Through interviews with her and others with varying diagnoses I reached an insight in their situation. To my surprise they still favored a visual form of communication before an auditory or tactile form, because it?s easy to survey and quick to interpret.

This thesis gives suggestions as to how to design a wooden-based wave-power buoy. The thesiswas carried out at Uppsala University in collaboration with the Division of Electricity and AppliedMechanical Engineering. The product was conceived and developed taking into consideration anumber of requirements put forward by the supervisor, Magnus Rahm. The most importantdemands were that the material used should be able to withstand pressure from the sea withoutbeing damaged and that the production costs should be low.Department of Engineering Sciences, Division of Electricity at Uppsala University was visitedseveral times to discuss issues including the various ideas with the supervisor Magnus Rahm, andwith several people in the department.The work started by studying available literature in order to get background information aboutsuitable methods available for the project and to see how similar projects were carried out. Thereason for this was to get a better understanding of this particular problem and how to solve it.After consulting the supervisor, the group decided to construct four different buoys using fourdifferent materials.

This thesis gives suggestions as to how to design a wooden-based wave-power buoy. The thesiswas carried out at Uppsala University in collaboration with the Division of Electricity and AppliedMechanical Engineering. The product was conceived and developed taking into consideration anumber of requirements put forward by the supervisor, Magnus Rahm. The most importantdemands were that the material used should be able to withstand pressure from the sea withoutbeing damaged and that the production costs should be low.Department of Engineering Sciences, Division of Electricity at Uppsala University was visitedseveral times to discuss issues including the various ideas with the supervisor Magnus Rahm, andwith several people in the department.The work started by studying available literature in order to get background information aboutsuitable methods available for the project and to see how similar projects were carried out. Thereason for this was to get a better understanding of this particular problem and how to solve it.After consulting the supervisor, the group decided to construct four different buoys using fourdifferent materials.

The exclusion of visually impaired from the information flow presented to us through signs was what led me into this project. With a growing amount of information being presented to us on signs and digital information surface the need of communicating this information in a way that could be read by visually impaired is evident. Looking into different ways of communication, my goal was to create something that filled the need of the visually impaired without branding them as disabled. Having a close relative with bad eyesight is became evident on how much it limited her in her everyday life, not being able to navigate herself without the support of her husband. Through interviews with her and others with varying diagnoses I reached an insight in their situation. To my surprise they still favored a visual form of communication before an auditory or tactile form, because it?s easy to survey and quick to interpret.

Industrial buildings are increasing all over Sweden. Farmers are building new modern facilities and the government chooses to build new halls to invest i youth sports. Glulam is the most common framework but there are limitations because of the transport. Therefore, there is a need to develop new solutions to increase the use of glulam.The maximum torque in the eaves was found in the frame with a roof pitch of 18 degrees and a wingspan of 25 meters. Using hand calculations according to Eurocode and comparison with the computer software StatCon, the maximum torque, shear force and utilization rate is calculated.

Title: Kvarteret Tvättstugan, an apartment building with massive wood construction. A thesis about acoustic and fire requirements and a comparison of energy and moisture aspects. Earlier restrictions in the Swedish legislation have resulted that only a small percentage of the apartment buildings that have been built are designed with a massive wood construction. It has been allowed to build unrestricted with wood since 1994 as long as the function of requirements are fulfilled. This change in the rules together with the great environmental benefits of wood has led to that more companies choose to build apartment buildings with wood. One of these companies is Folkhem Production AB.