Spatial design for children nine to twelve years old at the Halmstad City Library. An investigation about the specific needs of the target group and how the child department can be designed to stimulate their experience of visiting the library. The aim was to create a spatial concept from the children?s ideas that inspires to playfulness and lust to read at the library. A more personal goal was to collaborate with an external part to prepare for my future role as a designer within child culture.

This report describes the design and implementation of a multi-master, packet based protocol for small and tiny microcontrollers where resources are limited. The protocol was named "Tiny Controller Network" or TCN for short. The protocol is meant mainly as a control bus for automation and sensor acquisition applications but due to its flexibility can also be used for other purposes as well. It borrows some of its Functionality and design ideas from the well known CAN bus and Modbus but also has a number of major differences like the use of standard hardware and time synchronisation. One of the key aspects during the design was the use of very little system resources and common on-chip hardware peripherals like a UART.

Building Automation Systems in commercial buildings are often designed and installed by different contractors, using equipment and components from different manufacturers. The lack of an accepted communication standard has resulted in a few different standards. Many manufacturers of building automation systems only support one, a few or none of these standards, while developing proprietary system solutions. Regin, who develop such equipment, are planning to adopt an open communication protocol specially designed for building automation - BACnet. As a step in that direction this thesis was announced with the purpose to investigate the possibility to implement BACnet in one of their products and to gain more knowledge of the BACnet protocol.

In this study I have analysed the national tests in Swedish between the years 2006-2010. These tests are given to all students in the public schools in grade 9 and 10. I wanted to see if I identified an over-representation of a certain category of people in the texts given to the students. I analysed the texts from an intersectional perspective and I used primary Lena Martinsson (2007), Framtidens feminister and her categories and theories and Moria von Wright (1998) Genus & text- när kan man tala om jämställdhet i fysikläromedel?, and her gender categories in my study.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good Functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good Functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

To support, enhance and, in the future, develop the activity within the county councils in Sweden, IT support systems are currently used to a large extent. The need to document is central to the health care organizations and the counties have come a long way in the introduction of electronic patient record systems (EPR). The aim of the EPR systems is to support the care processes and the clinical professions in their work.This is a master thesis in the area of human-computer interaction (HCI), Department of Information Technology at Uppsala University. The aim of the thesis was to describe and compare the five most common EPR systems in Sweden. The comparison will focus on some usability aspects and on how well they support the users in their clinical practice.

Within system development users have rarely been involved or received much attention during the development. Most of the times, the primary focus within system development lies on insuring Functionality, rather than making the system usable. The literature specifies that a non user-centered approach can contribute to a product with low usability, which can lead to an ineffective and unsatisfactory experience for the end users.The purpose of this thesis is to begin an investigation to see if the use of non user-oriented system development methods is a possible cause of low usability in the final system.To achieve the purpose of this thesis, we have conducted a case study. Within the case study we examined the usability of a time reporting system. The case study included seven minor studies; an investigation concerning the development of the system, an expert evaluation of the system, interviews and observations of users, developed paper prototypes and executable prototypes, both which user testing was performed on.The result of this study shows that by working with user-entered methods, the usability in the time reporting system increased after the design had been revised.

The effects of anthropogenic climate change are becoming more and more visible as being highlighted by scientists, politicians and media. The causes of droughts, floods, melting ice caps and rising sea levels can all partially be traced back to human activities. In this study, I examine where the future climate refugees of Kiribati, Tuvalu and the Marshall Islands should go when inhabitants of these low lying island nations are forced to leave their disappearing territories due to sea level rise. By using a normative method of analysis i egentlig mening, arguments deriving from certain values will be presented to confront the problem. These values originate from Edward A.

C3LOOPS is an application for DJs and VJs based on surface interaction. A system is said to be based on surface interaction if it presents content on a two dimensional, endless surface that a user navigates through zoom, pan and incremental text filtering where processing is tightly coupled with the content without breaking the workflow. C3LOOPS is designed to encourage improvisation and collaboration. During improvisation changes occur rapidly. Allowing navigation through time as well as the two spatial dimensions of an interaction surface the possibility of unlimited undo operations opens up.

Graphic profiles are a part of companies? brand expressions. The graphical values reflect the brand values the business wants to convey. They consist of different graphic elements such as logo, company sign, colour schemes, templates, rules, fonts, pictograms, formats and references to how different graphic elements should look, for example, business cards, signs and materials for websites. This thesis aims to examine why firms choose to replace their graphic profiles by studying their underlying motivations.

This thesis describes redesign and adaption of a products housing. In order to make it more economical to produce at a lower production volume. The thesis is based upon a prototype that a previous student developed for injection moulding. The goal is to find alternative manufacturing methods, but also to identify parameters that affect the cost of the injection moulding tool.The housing must be tough in order to protect the circuit board inside. But at the same time it must allow sound, light an electrical communication to pass through.

This bachelor thesis is about an ultrasonic sensor, implemented in a bubble chamber in Artis. The sensor consists of the piezoelectric sensor and an electronic control circuit. The control circuit consists of a programmable microprocessor, PIC18F2420 and a circuit, which sends the excitation signal to the piezoelectric sensor, and later receives the echo. This bachelor thesis consists also of a theoretical study, which examines different techniques of liquid level sensing in a chamber. The study discusses which factors are important in liquid level sensing and examine accepted methods.

Today, the requirements on doors and door sections in buildings are often many andtightly restricted. Especially in public buildings, the requirements for safety andFunctionality must cover the needs of larger groups of people. These strictrequirements have often led to doors and door sections in public buildings being verycomplex and difficult to correctly install without any complications.This diploma work has been carried out in cooperation with Werket Architects,which estimates a high percentage of flaws regarding aforementioned components, inprojects of the type described. The company therefore wanted to investigate howthey could develop their remit in door production, which is the projection and designof blueprints. By taking part of installers opinions on how they want the blueprints ofdoors and door - sections to be designed for the best installation possibilities,develop¬ment areas, and to some extent improvements regarding the company's useof accounting techniques, could be provided to the company.The study shows, among other things, that there is a possibility of development in thefunctional descriptions that entail the doors' fitting components.

The market-leading wage and PA-.system for the Swedish public sector Palasso is developed in Karlstad. In order to achieve the highest quality of code , the developing team behind Palasso has been conducting extensive testing. Testing is done to ensure that the software does what it should do. However, the testing has been done at a high level. In order to continue to evolve, the group that develops Palasso has started to look at the new development methods that have become popular in the computer industry in recent years.