Since 2004, wind power has had the largest installation of new capacity compared to other energy sources in Sweden. Accommodating new wind power may require strengthening or rebuilding of the existing grid in areas where the grid is already loaded to maximum capacity. This master thesis examine the possibility of a new 400/130 kV substation in Yttermalung, Sweden, with a connection to the two neighboring regional grids in Dalarna and Värmland owned by Fortum. This substation would provide a new connection point to the Swedish transmission system as well as an interconnection of the two, currently separated, regional grids. Different expansion scenarios where a substation with and without series compensation or a phase shifting transformer (PST) to control active power flow were studied.

This thesis has been done at the powder department (GH) at AB Sandvik Coromant in Gimo. With a rheometer measurements has been made on raw materials and powder blends. The focus of this report has been to find correlations between raw material powders and press data, comparisons have also been made between raw materials and powder blends.The rheometer can show information of how a powder act in flow conditions, together with air and with pressure. Analyses has been done comparing the rheometer data with press parameters (for example: rejected orders, weight variations and the compaction pressure) with the goal to find correlations between the powders flow properties and the powders compaction in production.The measurements and analyses have been showing that the powder flow properties depends on the powders composition and that properties like flow rate, aeration and permeability varies between powder blends and batches of the same powder sort. It seems to exist a correlation between the pressure force and the flow rate of a raw material.

A good flow of information in organizations is one of the key aspects of how we define a well-functioning organization. The information flow could be internal as well as external between actors within as well as outside of the organization. In a logistics organization this flow of information is equally important as in any other kind of organization. In this paper we have explored information flows in logistics organizations by applying, boundary spanning and the mobile-stationary divide perspective. In boundary spanning the main goal is to erase or relocate some of the boundaries within an organization, in our case to make the flow of information internally as well as externally better.

A good flow of information in organizations is one of the key aspects of how we define a well-functioning organization. The information flow could be internal as well as external between actors within as well as outside of the organization. In a logistics organization this flow of information is equally important as in any other kind of organization. In this paper we have explored information flows in logistics organizations by applying, boundary spanning and the mobile-stationary divide perspective. In boundary spanning the main goal is to erase or relocate some of the boundaries within an organization, in our case to make the flow of information internally as well as externally better.

Today we live in a world where the demands increase in the aeronautics industry. This creates a situation where no mistakes are allowed about the regulations and for those who are supposed to follow these. Safety comes first, tracking of components, Service Bulletins which are recommendations from the manufactures and Airworthiness Directives which are demands from the authorities, these need to be updated at all time and everything that is done on a aircraft need to be documented.This creates a situation where today maintenance shops need to have full control of all parts of the organization, which creates a need for a working data system.The goal with this exam work is to evaluate the best way to implicate the new bought data system called "System Aircraft Management" on the basis of the needs of Täby Air Maintenance AB. The system are supposed to get started technically and also be implicated to the users of the system. This work will be focused to create a effective working plan to get SAM implicated with no interruption in the daily work.

A patient simulator for testing anaesthesia machines has been developed at Maquet Critical Care AB, to reduce costly and time-consuming experiments on animals. The device simulates human lungs regarding lung dynamics and volume, uptake of anaesthetic agents and the production of carbon dioxide, heat and moisture. Further demands on the simulator are durability and size; the device shall be compact enough to be moveable.The resulting simulator fulfils the requirements and enables better repeatability and ability to test extreme cases than experiments on animals do.Uptake of the anaesthetic agent is achieved in a active carbon filter and controlled by regulating the flow. The flow is created by a regenerative blower and controlled using a proportional valve. The uptake can be set by the user or by a simple uptake model modified to recursively handle changes in the concentration of anaesthetic agent.Carbon dioxide is fed into the system from a tank by a mass flow regulator.

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution.

At Forsmarks Kraftgrupp AB (FKA) forces on pipe systems due to transient flow are frequently calculated as a step to verify their structural integrity. In nuclear industries these forces are often calculated with a one dimensional thermal-hydraulic analysis-code called RELAP5. When calculations regarding more complex geometries are needed, the three dimensional code Fluent is often used. This code is highly time consuming and requires large computational power.This projects aim is to compare calculations of pressure, flow and forces carried out by RELAP5 and Fluent for an arbitrary pipe section during transient flow conditions. This has been accomplished by constructing a simple geometry for which a transient flow is simulated in both programs.

I denna rapport predikteras livslängden, med avseende på utmattning, för en hjullastarskopa. Två av de mest kritiska svetsarna utvärderas enligt IIW:s (International Institute of Welding) rekommendationer genom nominella spänningsmetoden, hot spot-metoden och effective notch-metoden. Beräkningarna utförs med hjälp av finita elementmetoden. Genom att utföra töjningsmätningar på hjullastarskopan i drift erhålls spänningsdiagram. Dessa uppmätta spänningsdiagram analyseras med rain-flow count-metoden.

The thesis work has been carried out at Volvo Aero Corporation (VAC) in Trollhättan. VAC has entered a partnership as developing and producing partner with engine manufacturer Pratt & Whitney and is currently at the starting phase of producing the turbine rear frame (TEC) to the engine PW1000.The purpose of this study was to create a report on process level that describes the conditions and the potential with PW1000 TEC to reach the product cost calculation taking into account lead times and describe alternative method solutions.The report describes a comparison between the present flow (2012), a flow based on product cost calculation (2016) and a potential flow (2016). The work has mainly been based on acquiring the knowledge and information available to inspect the present flow; this has been done by workshop observations, meetings and gathering of the information that is available on the work site for the PW1000 TEC.The information obtained has been merged into an Excel document, called Roadmap. It serves as a roadmap with current situation as the start and the potential flow for 2016 as the goal. With the roadmap as a tool, assumptions have been taken considering the flow and how it will change, where processes have been eliminated, reduced or marked as a problem..

This report is the result of an investigation of the possibility to use RFID-technology in a producing company. The investigation is focused on a flow between the company?s producing subsidiary company in Lithuania and its main facility in Sweden.RFID is the abbreviation for radiofrequency identification. The RFID-technology forms the base of a system with wireless information transmission between an object to which a transponder, also called tag, has been attached and a reader. The information is transmitted by radio waves and the system is equipped with software that can digitalise the radio waves.

A good flow of information in organizations is one of the key aspects of how we define a well-functioning organization. The information flow could be internal as well as external between actors within as well as outside of the organization. In a logistics organization this flow of information is equally important as in any other kind of organization. In this paper we have explored information flows in logistics organizations by applying, boundary spanning and the mobile-stationary divide perspective. In boundary spanning the main goal is to erase or relocate some of the boundaries within an organization, in our case to make the flow of information internally as well as externally better.

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution. The work proceeded with an extensive search for abrasive flow meters along with obtaining information about flow measurement in general. When the search for abrasive flow meters resulted in nothing all the efforts were concentrated on finding a principle of measurement that could cope with the criteria.

The present study is embedded in the research field of Personal Information Management (PIM) and its goal is to contribute to this research area by showing information management aspects in untraditional contexts, as in the social networking site Twitter. The aim and purpose of this two year's master thesis was to investigate the beha-viour of librarians within the context of Twitter. The objectives of this thesis focus on the query of the informa-tion management aspect of Twitter, and on the investigation into whether Twitter offers the possibility to reach a state of flow while using it, as well as inquiring into the relationship between Mihaly Csikszentmihalyis flow theory and PIM. The theoretical framework of this thesis is centred upon the flow theory and the conditions that are necessary to reach a state of flow. To fulfill the purpose of this thesis a directed content analysis is applied as an investigative method, where its in-depth research aspects will be applied upon the empirical material, which contains 429 tweets.

Det här arbetet handlar om flow och hur begreppet samverkar med olika aktiviteter i våra liv. Bakgrunden till flow förklaras inledningsvis i kapitlet om teoretisk bakgrund och sätts senare i relation till inre förändring, socialt samspel, fysisk aktivitet, kommunikation, samt pedagogik. Syftet med arbetet är att ge svar på hur flow kan användas i undervisning. Som metod för datainsamling har jag gjort en gruppintervju med fyra lärare aktiva vid Musikhögskolan i Malmö. Gruppintervjun fungerade som ett vardagligt samtal mellan fyra personer och resultatkapitlet är sammanställt i sex rubriker: Introduktion; Personernas uppfattning om flow; Vägar till flow och hinder på vägen; Gruppflow; Flow, kvalitet och kommunikation; samt flow och undervisning.