AimThe main aim of the study was to investigate the difference in bilateral deficit between rowers and sprinters during maximal eccentric/concentric muscle actions.? Are there any significant differences in bilateral deficit between rowers and sprinters?? Do the amount of years in practice effect the bilateral deficit?MethodFourteen male subject participants divided in 2 equal sized groups (7 individuals in each group; rowers and sprinters) performed maximal unilateral/bilateral eccentric and concentric muscle actions in a leg press machine at a velocity of 0.2m/s. The range of motion in the knee joint was 70° ? 140°. Dependent t-tests have been performed within each group pre and post test.

The aim of this study about wind power planning in forest was to examine the factors and restrictions, which represent technical limitations, biodiversity, tourism and amount of energy for wind farms in Kronoberg County. Suitable areas for wind power were identified from the collected information about planning principles and potential conflicts. From the suitable areas the potential energy gain is calculated. Methods used were mainly a literature review, interviews with experts and practitioners, GIS analysis and a rough calculation of the energy gain. The section of information and facts describes in general wind power planning and possible conflicts.

In this study I analysed how burning affects sprouting ability and survival of oak (Quercus robur) during the first season after a burn in southern Sweden. The study consisted of two separate field tests; in the first, two 300 m2- plots in western oak dominated forest were burned to analyze the fire behavior and the immediate mortality of oak and beech seedlings defined as individuals (> 20cm of height). At the end of the season almost 50% of the oak seedlings had resprouted while the beech seedlings had 100% mortality. An attempt to investigate the effect of the burn of artificially sown acorns was totally ruined by wild boar grouting before any conclusive results could be seen. In the second test the resprouting ability of oaks of varying diameters (average BHD 7-9 cm, range 2-42 cm) was examined one season after a prescribed burn in southeastern Sweden.

Human presence has always influenced the surrounding areas, the forest as well. Structure and species composition have changed during human land use. Knowledge regarding these changes should be of great interest for conservation and forestry. We have analyzed human impact on the tree species composition on five study sites during 2000 years in Ångermanland, Sweden. More specifically the change in tree species composition in percentage amongst alder, birch, spruce and pine over time.

AbstractThe purpose of my study is to examine how preschool children experience nature and how the educationalists at the preschool can make nature more exciting and support the children?s personal growth. I have also studied what the educationalists of the preschool do and what they can do to make nature more interesting and playful for the children. Observations and interviews have been conducted at a preschool in a small town. The preschool is situated close to nature, that is, close to a small forested area.

Until the beginning of the 1900:th century the paper making process was handicraft. The paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard.

Tree fiber lengths controls properties like strength and smoothness in paper and other wood products. For forest researchers it is of interest to be able to determine the fiber lengths in standing trees. Mo?rling et al. (2003), among others, have developed methods to estimate fiber length distributions in standing trees without damaging them.

Beacon AB has been producing Gobos for some time. A Gobo is a small round sheet used in projectors almost like a slide. It is used mostly in the commercial and entertainment business. Today these Gobos are created by using a film (also called mask). A digital exposure machine called LIOS has been developed to make it possible to create Gobos using direct exposure.

The purpose of this study is to investigate if there is enough consideration taken to sensitive forest areas close to water or wetlands during clear cutting assignments, and to estimate the extent of damage made by forestry machines used at that time. A field and literature study is used to show how to improve and prevent the damage made in the wake of the machines. This study is made for Sydved, and shall culminate in a policy to prevent ground damage during their clear cutting assignments. The areas which were part of the field studies were clearcuttings on fine grained soil close to water and wetlands. The purpose was to find out if the water had been affected, what had been done to prevent ground damages and what more could have been done. The results of the field studies show that more work needs to be done to reach up to expectations. More information about the assignment area, better planning of sensitive regions, and strengthening of the main haul roads with brush are some of the improvements that can be done. There is also a need for more exact guidelines, follow-ups and education for everyone involved to have the same goals and understanding to prevent ground damage..

Burnt Spine-cap Sárcodon fuligíneovioláceus are one the most endangered mycorrhizal fungal species in Europe. They have their main distribution in Sweden. It form mycorrhiza with pine and dependent on limestone, which makes it connected to a rare environment. It has therefore been important to study the ecology of it further and to recognise the requirement it has on the environment more accurate and what it need to establish in a new area. In this study, 31 of 34 known sites in Sweden was visited and studied in field and their history analysed through aerial photographs.

I mitten av 1990-talet närmare bestämt 1996 gjordes en film kallad Diary of a Camper. Filmen handlade om en person som satt och lurpassade på sina fiender i ett datorspel. Det som var speciellt med denna film var inte handlingen eller något fantastiskt kameraarbete. Nej det som var speciellt var det faktum att filmen spelades in i ett datorspel. Denna film anses vara startskottet för machinimakulturen som idag omfattar flera tusen utövare världen över.Det var personerna bakom Diary of a camper som myntade uttrycket machinima som är en sammanslagning av de engelska orden ?machine? och ?animation? alltså maskin och animation.

During the transportation of logging residues (LR) the material´s low density is a problem that results in low use of pay-load capacity. Comminution or compression of LR are possible methods to increase pay-loads. In the present thesis studied a bundling machine which was mounted on a truck chassis, and the subsequent transport and crushing. The truck bundler created bundles that were larger and longer than other bundling equipment on the market. The objectives were to determine the total time consumption and its allocation over work element and machinery, to measure dry matter (DM) content of green and brown LR-bundles.

Outdoor education is a teaching method which has several advantages to traditional classroom tuition. Its ideas have a long tradition and find support in the current Swedish curriculum. The place for the tuition is a central aspect within outdoor education. This essay aims to investigate what good places for outdoor education look like as well as discussing how the characteristics of such places can be used when designing schoolyards. Previous research shows that nature has characteristics that suit outdoor education well.

Rimaster Kisa AB is a member of the Rimaster Group, the corporation was bought from Samhall AB in January 2007. The corporation is producing mechanichs needed by the Rimaster group as well for external costumers. Samhall AB is now functioning as a provider of labor for Rimaster Kisa, as the company is hiring personnel from Samhall AB. The company has earlier have had problems with their lead times being far too long. This has resulted in that the management decided to invest in a new edging press.

A manufacturing machine at the engineering company Sandvik Coromant has a positioning table which task is to move an item linearly. The positioning table has a linear motor capable of high velocity and acceleration. This makes it possible to achieve short cycle times and a more profitable production.The purpose of this thesis is to bring forward a new concept which is more adapted to the requirements of the positioning table. The reason is that the current positioning table provides an unnecessarily positioning accuracy of 0.01 mm, while the requirement for the positioning accuracy is just 0.1 mm. The goal is to reduce manufacturing and component costs.To develop a suitable solution an approach for the concept development process has been performed.