AbstractElectricity consumption is a globally increasing problem caused by the high share of electricity produced in coal power plants. These contribute to high carbon emissions when only about 1/3 of the heat generate electricity and the remaining 2/3 of the heat cools off. Combined heat and power plants (CHP) have high efficiency because they use the residual heat for domestic heating. The CHP plant often use fuels from renewable resources, giving them a lower carbon footprint, but are also depending on the heat demand. If electric powered products such as drying cabinets convert to heat powered products more environmentally friendly electricity will be produced by CHP plants, which can supplant electricity, produced from coal power plants and reduce carbon emissions.

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

The Goal with this Master of Science thesis is to expand the possible turbine efficiencymeasurements on an exhaust turbocharger. It was done as a part of the CICERO competencecentre. To feed the turbine with air a special flow rig has been used. Instead of loading theturbine by just restricting the compressor flow a docking system for an electrical dynamometer isdesigned to use the dynamometer as an additional loading source. By using an electricaldynamometer as loading device for the turbine, measurements are not depending on compressorperformance.A large part of the work consists in designing accessories for the dynamometer.

This thesis is a feasibility study into how Fresenius Kabi may rationalize their destruction process in regards to cost, recycling, and work environment. The two main objectives are to identify scrap flows and the possibility to improve or replace the equipment that is now carrying out the physical scrapping. The flow has been visualized by a flow chart of the material and communication. A chart of the problem established to visualize where improvements are necessary. Based on the problems proposals are presented on how to improve the flow thru the plant.During analyze of the physical scrapping equipment it was also necessary to take a deeper look at how they are carrying out there work today, how does the procedure look like, working environment and where are the weaknesses.

Storm water is defined as runoff from precipitation such as rain or snow. It is collected in sewage disposal systems and since it mainly originates from urban areas it can contain high levels of heavy metals, nutrients and oil etc. Polluted storm water is currently treated by different methods such as wet ponds, constructed wetlands and filter strips. This study investigates these methods, which in earlier studies have shown to give varying results regarding their treatment efficiency.This thesis has been written on commission of SWECO VIAK and was aimed at studying those parameters that may affect the treatment efficiency of nutrients and heavy metals in storm water treatment facilities (STF:s). Through literature studies the dominating treatment processes in ponds and wetlands were examined.

Problems arise when the number of products in stock does not correspond with the number of products the information system says the company has in stock. (Sharda & Agrawal, 2012) In order to change that, major changes has to be made when it comes to making continuous improvements and to raise their standards regarding product availability and record inaccuracy (Wild, 2004).The purpose of this study is therefore designed to identify factors affecting the balance differences and what impact it has on the efficiency of material flow. The demarcation of the work is that Atlas Copco has begun working with Lean and it will not be investigated nor the relationship between balance differences and Lean. The study was based on answering the following questions: What influencing factors can be identified for balance differences? What factors are relevant to the efficiency of material flow? What kind of impact the balance differences has on these factors?In order to answer the purpose and issues, a theoretical framework has been developed with help of literature studies and an analytical model.

This report was performed in order to evaluate a new technological measure and focuses generally on a heat pump system to a HWC-washing machine. The client is Asko Appliances AB, a company well known for its environmentally friendly products. The goal of this study was to improve the energy efficiency of a washing machine by combining a heat pump device to the heater of the wash water, in order to reduce the energy consumed for heating the water. Besides reducing the energy consumption in heating the water, the washing machine was required to meet low noise and short operating time specifications. For that purpose, nine trials in three test series have been carried out.

AbstractEmbla 5 is an office building which has done a large improvement. The clients of this building has made an order of WSP and the student Anders Kempe to calculate the use of energy for the building, and after that result proposing further measures which can decrease the energy use of Embla 5.The ground for this report is when calculation of the present energy use of the building is stated. To make that information of a number of parameters such as envelope, the heating system and ventilation has been located and set in to the simulation program IDA ICE which calculate the energy use.To improve the energy use further this project has been concentrated to change the system of ventilation. Today the ventilation system is of the kind CAV (constant air volume) and the air flow is dimensioned for after recommendations from BBR and Arbetsmiljöverket in the office spaces. Consider that Embla 5  is an office building where the people only staying for 8-10 hours/day so was the ide to see how much energy saving if the air flow is reduced the time people not being in the building.

This master thesis was carried out at ELFA, one of the largest catalogue distributors of electronics in northern Europe. ELFA offers a wide selection of products such as measuring instruments, fuses and screwdrivers. The master thesis handles the possibilities of an increase in the internal flow of products. The background to this problem is ELFA?s acquisition of two new companies, which brought the product range in the warehouse from 55 000 to 80 000 products.

 This report deals with thecollaborative project between FagrellProdukt Utveckling AB and studentsfrom the Faculty of Science andTechnology at Uppsala University. Theoverall objective of the project wasin addition to developing students'abilities, to help Fagrell withverification and development ofFagrells prototype, Fundamental flowreactor, for flow chemistry. Theuniqueness of Fagrells flow reactor isthat it should be simple andaffordable compared to competing flowreactors in the market.The verification was done bylaboratory and simulation sessions.The verification shows that Fagrellsidea on how to construct a flowreactor is very good.The development included bothtechnology and business. The result ofdevelopments can be helpful for thecommercialization of Fagrell flowreactor..

The dishwasher is a wide spread product that occurs in many households. It saves the user time,water and energy. When using a dishwasher instead of doing dishes by hand a lot of energy issaved.The importance of lowering the energy consumption does not only come from the consumerwinnings but also from an environmental point of view. Scientists are certain that the globalwarming comes from the emission of green house gasses that is created by human consumptionof oil, gas and coal.Dishwashers today are a lot more energy efficient than older dishwashers, but there are stillmargins to lower the energy consumption. The aim with this project is to investigate thedishwasher and it?s washing cycle, noting different phases and components that contribute towaste of energy.

In industry applications, such as power supply plants, the issue of interaction between fluid and structure is always presented. More precisely, the fluid flow affects the structure by applying force(s) on it and vice versa. As a result, the structure can move (vibrate) or deform. A good understanding of this problem can help to design the system in term of safety, stability and efficiency.This project aims to optimize and test the Unicorn FSI solver from the FEniCS project [1] to simulate the interaction of fluid and structure in an experiment, which was carried out at Vattenfall Research and Development. The target is to improve the Unicorn FSI solver to cope with a real industrial problem.

The exhaust arrangement on a Scania V8 consists of one manifold at each bank connected to a twin entry turbine (8-2-2). A study in GT-Power has shown improved performance and reduced cylinder to cylinder variations using two manifolds at each bank in combination with a single entry turbine (8-4-1). This thesis work analyses the difference in performance shown in simulation and verify it by engine test.The initial work was focused on simulation in GT-Power. Investigating how exhaust manifold volume and pulses effects the turbine efficiency and the mean effective pressure during the gas exchange. To verify GT-Power simulations four engine tests with different exhaust arrangement have been made.The results from GT-Power simulation indicate that a larger exhaust volume improve the turbine efficiency.

The investigation was initiated because of the high workload of the sellers and, additionally, because the Tunadal sawmill has received low ratings in customer surveys. Thus,  two main approaches are adopted here,  the first being to investigate which of the three methods  of working, namely, market divided flow organization, function organizationand flow organization with collaboration, proves to be the most beneficial. The second is to investigate whether there is an available method to ease the daily work. A literature review has been made in order to determine more efficient ways for the sellers to work in the Tunadal sawmill. During the investigation, an in-depth investigation into the total quality management using a balanced scorecard as a management tool was conducted.

Stormwater run-off from surfaces such as roads or rooftops is often polluted with heavy metals and nutrients. Many of these substances can cause great damage in biota if they end up in the recipient. In Sweden constructed wetlands and ponds for treatment of stormwater are frequently used, since research has shown that these treatment ponds are reducing stormwater pollution considerably to a low cost. The knowledge of these pollutant removal mechanisms and how follow-up and assessment of the ponds should be performed is still limited.To determine the pollutant removal efficiency of the stormwater ponds it is recommended that flow-weighted water samples are collected from both the inflow and the outflow of the pond. This method demands considerable resources of time and money for installations and analysis.