Today more effective computer programs are in use, regarding design of geotechnicalconstructions. There is a risk that the theoretical background of the computerprograms, its limitations and the signification of the choice of soil parameter isforgotten when the computer programs become more user-friendly.This Master thesis deals with simulation and analysis regarding three computerprograms, FEM-design, with the addition Raft, Plaxis and BE-slab. Comparisons aremade for settlement and maximum moment in a concrete-plate. FEM-design is a threedimensional FEM-program, foremost created for design engineers. Plaxis is a twodimensional FEM-program, intended for geotechnical engineers while BE-Slab is aBoundary elements program in two dimensions that is mainly used by designengineers.

Today more effective computer programs are in use, regarding design of geotechnicalconstructions. There is a risk that the theoretical background of the computerprograms, its limitations and the signification of the choice of soil parameter isforgotten when the computer programs become more user-friendly.This Master thesis deals with simulation and analysis regarding three computerprograms, FEM-design, with the addition Raft, Plaxis and BE-slab. Comparisons aremade for settlement and maximum moment in a concrete-plate. FEM-design is a threedimensional FEM-program, foremost created for design engineers. Plaxis is a twodimensional FEM-program, intended for geotechnical engineers while BE-Slab is aBoundary elements program in two dimensions that is mainly used by designengineers.

Today more effective computer programs are in use, regarding design of geotechnicalconstructions. There is a risk that the theoretical background of the computerprograms, its limitations and the signification of the choice of soil parameter isforgotten when the computer programs become more user-friendly.This Master thesis deals with simulation and analysis regarding three computerprograms, FEM-design, with the addition Raft, Plaxis and BE-slab. Comparisons aremade for settlement and maximum moment in a concrete-plate. FEM-design is a threedimensional FEM-program, foremost created for design engineers. Plaxis is a twodimensional FEM-program, intended for geotechnical engineers while BE-Slab is aBoundary elements program in two dimensions that is mainly used by designengineers.

During the last decades the fertility of dairy cows has declined in the same rate as the milk yield has increased. This is a result of the negative genetic correlation between milk yield and fertility, failure to show estrous signs and metabolic problems in the cow. The purpose of this review was to investigate the function of metabolites and hormones as markers for disturbances in fertility, health and production in the dairy cow. There are several metabolites that are suggested to indicate the cow?s energy balance.

Test bench for air bearingsThis thesis work consisted of bringing forward and defining the test parameters relevant for a test bench and constructing a test bench that can test and verify the largest existing air bearings that are of use in Micronic Laser Systems AB machines. Because the knowledge about air bearings is limited it is thought that with the help of the test bench the knowledge would increase and in that way improve the air bearings.After learning more about air bearings and their purpose at Micronic Laser Systems AB, I started the concept phase for the test bench. For each part in the test bench I consulted my two tutors, Torbjörn Hedevärn and Johan Bergqvist, at Micronic Laser Systems AB. The final concepts where documented as 3D-modells in Solidworks and some of them have been tested in Solidworks FEM-program.The test bench is designed so that, with the help of a pneumatic cylinder, 25 kilo weights are placed on the air bearing to test its stiffness, damping and the pressure performance under its surface area. To test these parameters the test bench has to have a pressure meter, accelerometer and a microcator.

Holmen Skog is one of the largest forestry companies in Scandinavia and they depend heavily on a large network of forest roads for production and logistics in connection to their forestry operations. The company recently introduced a new system for planning of road management. The system will also be developed with the intention to facilitate the monitoring of actions performed by road contractors. This report will provide information to support future decisions regarding further development of the system, after its introduction. In addition to a presentation of results from interviews, the report also provides a smaller study of the different subjects associated with roads, process work and process development. The study is largely based on interviews with road contractors that perform work for Holmen Skog today.

When models are used to describe physical phenomenon during development or modification of a technical system, it is often possible to reduce both the time needed and the overall development cost. With the use of models it is also possible to investigate the potential of the selected solution, without the need for any expensive details and testrigs. In many cases it is also not possible to test all the aspects regarding the functionality that are desired from the system, without using the complete and final product.In this case a model based approach has been used to optimize the different parameters in the new snubbing mechanism for the Nose Landing Gear Retract Actuator on the JAS39 Gripen.During the simulations, upper and lower boundaries were calculated for the length of the spring and the diameter for the restrictor. The governing constraints were given by the requirements for the retraction time during cold conditions and that the amplitude of the alternating loads in the uplock mechanism were brought to an acceptable level.The most promising results from the simulations were then used in a limited number of trials in the hydraulic rig to verify that the configurations comply with the requirements.The final parameters for the snubbing mechanism were chosen to 35±1mm for the spring and 0.4-0.5 mm diameter for the restrictor..

As break downs of production transformers are costly and often result in long outages it is essential for reliability of operation that the transformers are manufactured to be robust. The aim of this M.Sc. thesis is to investigate if deviations should be made from the standard IEC 60076 ? Power Transformers in order to describe a robust large power transformer for procurement.The investigation has been conducted in three stages. In the first stage a definition of the term robust was developed in consultation with the client Vattenfall Vattenkraft.

This thesis is a survey and also an investigation of the different factors that affects the cracking that occurs in the inserts at AB Sandvik Coromants production in Gimo. The work that has been done has focused on two main factors, namely, powder characteristics and pressing parameters.AB Sandvik Coromant produces tools and tooling systems for metal cutting. They have some problems in their production of inserts. The problem is that cracks sometimes occur in the body of the insert, after it´s pressed. In order to investigate this, a preliminary study was made in which production principles were studied.

Today electronics becomes more and more complex and to keep low costs and power consumption, both digital and analog parts are implemented on the same chip. The degree of automization for the digital parts have increased fast and is high, but for the analog parts this has not come through. This have created a big gap between the degrees of automization for the two parts and makes the analog parts the bottleneck in electronics develop. Research is ongoing at Electronics systems group at Linköping University target the increase of design automization for analog circuits. An optimizationbased approach for device sizing is developed and for this a good optimization method is needed which can find good solutions and meet the specification parameters.

This thesis has been carried out onbehalf of Lindborg & Sons in Örsundsbroand is a concluding part of the Bachelorof Science program in ConstructionEngineering at Uppsala University. Theaim of the project is to make a plea fora database of good examples of themachine room types using Revit drawingprogram, and work out a correspondingworksheet .At the start of the process it becameapparent that there were somedifficulties in using Revit to creatingmachine room types of the variety whichthe company builds. For modelling ofoblique, curved and irregular lines, Ihad to use my AutoCAD Architecture andthen import them into Revit.The creation of calculus in Excel wastime consuming. On the other hand, it isa one-time work to create the template.The advantage of Excel is that there isno need for a re-calculation at the costof various types of machine hall. Allthat is needed is to replace the variousparameters.

Transportation constitutes a large part of the forest industry's raw material costs. Transport also contributes a significant proportion of the carbon dioxide emissions. In order to reduce both the cost and environmental impact different types of decision support are required. These, in turn, require extensive information about the road network and correct information on road path selection and transport distances. In the development of national road data base for forestry (SNVDB) a road selection application has been included.

The association between social parameters (i.e. socio-economy and level of education) and voting behaviour has been reviewed and analysed based on data from municipal council elections in Stockholm and Gothenburg in 2002. Some social scientists argue that the class voting is in decline and that new social cleavages have emerged. However, by using regression analysis techniques, this study implies a strong dependence of voting behaviour on social parameters, such as socio-economic status (SES) and level of education. Socio-economy appears to be a dominant predictor in the analysis.

Outages in the electric grid can be costly for society. Because of this, reliability is one of the parameters used to regulate network companies. Reliability in electrical grids can be measured with SAIDI, system average interruption duration index, which for Fortum Distribution has increased in Stockholm?s distribution network (11 kV) in the early 2000?s.By using outage data for Stockholm from 2011-2013, sets of parameters to be used for reliability calculations in the network information program Tekla NIS were derived. Two different options for investment were then analysed: changing old cables with high fault frequencies, and installing automatic switching in distribution substations.

Two haematological instruments intended for small animal clinic use were evaluated at the Department of Clinical Chemistry, Swedish University of Agricultural Sciences (SLU), Uppsala, Sweden. The QBC-V and Vet abc were compared to a reference instrument, the Cell-Dyn 3500. Fresh blood samples were obtained from canine and feline patients from the University Veterinary Hospital, SLU. The QBC-V was used for 111 canine samples and 78 canine blood samples were analysed with Vet abc. From cats, 23 samples were analysed with both instruments.