AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

Increased understanding of the mechanisms that operate in conjunction with the welding of metal surfaces may help to improve existing manufacturing processes, and to enable new products and combinations of materials. The purpose of the project has therefore been to acquire a deeper understanding of what is happening in the bond for steel and for the factors that form the basis for a bond to develop between metals in the production of laminates by pressing. The merge has been done by pressing and the surfaces after the experiments have been studied in detail in the scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and with interferenceprofilometry in Wyko, to provide a greater understanding of the mechanisms that influence the bonding in the interface between metals. The project was limited to contain the materials Docol 1000, HyTens 1200, Aluminum AA3003 and a commercial steel. The parameters varied in the experiments to study their influence closer are temperature, pressure, heat treatment and pretreatment. This has been implemented by pressing with varying temperature and pressure.

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

Glass has sophisticated front properties and are used as facades in high buildings. During cold periods, these glass facades could cause thermal discomfort, due to cold downdraught. Cold downdraught can be countered by placing heaters under glass surfaces. Nowadays technology offers highly insulating windows, which is why there is an interest to investigate the indoor climate with only underfloor heating. The research in this area is limited, and few empirical methods are available.

Österbyverken is an industrial estate in Östhammars municipality in Uppland, Sweden. Many different activities have taken place on the estate the last 600 years. During the last 15 years both health and environmental studies have been made by different companies. At the most recent study a great increase of metals in Nerån, a river that runs partly through and partly next to the estate, was identified with mass balances. The purpose of this thesis is to accomplish a deepened study about the reasons for the increase of metals in Nerån.

This report deals with handling and interim storage of soils which are planned tobe reused in construction works. The types of soils that are dealt with are gravel, topsoil and sand. The thesis work has been carried out in collaboration with Skanska Sverige Väg och Anläggning Sydost. The main goal is to find an area for using to store soil in between projects.Studies of laws and regulations regarding exploitation and storage of soil has led to a theoretical background upon which the report is based. Background informationhas also been gathered in meetings with the employees at Tekniska Kontoret and Länsstyrelsen in Jönköping.On the basis of literature studies results, a general template has been developed for which desirable properties a possible location should meet.The model was applied to find a number of possible options in the vicinity of Jönköping.

Delineation of recharge areas for aquifers is performed in the groundwater mapping process at the Swedish geological survey, SGU. This work is time consuming and performed manually. It is therefore desirable to develop a more general and repeatable method for defining recharge areas for aquifers.The purpose of this study was to investigate two other possible methods to delineate recharge areas for aquifers. The first method was to examine the possibility of using the topography of the bedrock to define the recharge areas for aquifers. To enable this, a method for generating the topography of the bedrock was developed.

AbstractSurface-water includes different kinds of pollutants from traffic and roads. To prevent these pollutants to reach nearby lakes one can construct surface-water ponds on locations with heavy traffic. At Bergviks shopping centre in Karlstad, two ponds, one smaller and one bigger has been constructed in order to decrease the pollutant pressure from the receiving waters of Kattfjorden. Several heavy metals are essential for plants and animals in low concentration but when they occur in higher concentrations, they become toxic to the organism. The larger pond at Bergviks shopping centre has a sedimentation function so the heavy metals sink to the bottom thereby not releasing directly in to Kattfjorden.

Lake lowering in sulphide-rich areas is currently a major environmental impact for surface water. This study focuses on whether there is a relationship between a gradient of lake lowering and surface water impacts in areas of sulphide-rich sediments, in order to better understand their contribution of heavy metals and sulfuric acid. Also, is it a reasonable method to use the reduced lake area in order to quantify the gradient? The survey was conducted by collecting water samples from reference lakes and lowered lakes from south to north in coastal areas within the county of Västerbotten. Water samples were then analyzed for TOC, pH, conductivity, anions, base cations, alkalinity, acidity, sulfate, Al, Cd, Fe, Mn, Cu, Zn and Pb.

Open pit mining creates huge amounts of tailings and waste rock deposits. Due to it's content of sulphide minerals, predominantly pyrite (FeS2), there is a risk of oxidation and formation of acid water containing heavy metals, known as Acid Rock Drainage (ARD). To prevent the process of oxidation, the tailings and waste rock have to be reclaimed. The most commonly used methods of reclamation are a coverage of water or soil. Mining also results in a large-scale interference in the landscape that will make an eternal change of its appearance.

Bachelor thesis, Trolley Innovation Project, has been unique in the sense that it has been carried out over the borders of Sweden. Iacobucci S.p.A, located outside of Rome in Italy is one of the largest manufacturers of interior equipment for aircraft in the world. With approximately 30% of the market Iacobucci S.p.A is one of the world's largest manufacturers of catering trolleys.The aim has been to produce a new competitive catering trolley for the airline industry. With customers and users in focus, the project team found that weight, ease of use, ergonomics and design were important aspects. Having a low weight of all the interior is particularly important when there is lots of money for the airlines to save in reduced fuel costs.

This is a booklet with information and inspiration about precast retaining walls. The three chapters contain information about concrete as a material, how the surface of the wall can be altered, and a chapter with ideas for a new precast wall. I have obtained information through books, interviews, lectures and fairs. The retaining walls on the market do not correspond to the requirements of the Landscape Architects I have interviewed. I have therefore considered their opinions in the chapter containing my new ideas for new retaining walls.

Storm water is rain and melted snow that runs off, primarily from impervious surfaces.Future storm water management is facing the challenges of increased precipitation, asclimate changes, and increased areas of impervious surfaces due to the expansion anddensification of the cities. Impervious surfaces reduce the potential for water to infiltratein the ground leading to increased surface runoff and higher peak discharge.The runoff coefficient is closely related to the percentage of impervious surfaces andrepresents the maximum percentage of a catchment that can contribute to runoff. In thisstudy, the objective was to evaluate the weighted runoff coefficient for three differenturban types; apartment buildings, townhouses and residential areas and a comparisonbetween today and the 1970`s was made.The runoff coefficient was determined by manual mapping of the different surface typesin each area based on data in the form of orthophotos and aerial photographs. The surfacetypes that were mapped were asphalt, permeable areas, tiles, sand/gravel and roof.Tiles and sand/gravel were the most difficult surface types to map. In order to see towhat extent these categories influenced the weighted runoff coefficient a sensitivityanalysis was carried out and the runoff coefficient based on surface type was changed indifferent scenarios.The results of the sensitivity analysis showed that the surface types tiles and sand/gravelhad little impact on the weighted runoff coefficient which in mainly due to the fact thatthe percentage of these surfaces types of the total area is small.The result of the study showed that the largest change in the runoff coefficient occurredin residential areas where the increase in the percentage of impervious surfaces causedby new roofs in the form of porches and garages and from paved or tiled driveways.

For Skattkärr IF a turf field with warming has been projected to increase field?s utilization hours and to have a longer period for athletes to perform their activities outdoors. The technique chosen to heat the plan is a type of a geothermal heating system without a heat pump. The brine, which is water with 30% ethanol, collects heat from the borehole and discharges it to a coil in the field. There is at position 11 boreholes but it is planned to increase the number to 31, which is the design for the facility.

The present work is a continuation of the ideas developed in previous projects during my Masters studies that explored the relation between pattern, form and space. Starting from the pattern multiplication for space construction the present project proposes textiles as an assortment of flexible expressions. The purpose of the project is to explore aesthetic and functional potential of textiles for out door temporary structures. This is to create a pattern interface which filters sunlight through a textile surface to offer instant sheltering solutions for out door activities. The project combines research and analyses of outdoor temporary structures and scope of textile in the area.