Within today?s organizations there is continual development work to increase efficiency and the power to compete at the market. Production development with focus on continual improvements constitutes an important part of the daily work within a lot of organizations today.The purpose of this study is to contribute to a part of the development process that Volvo Penta factory in Vara has in mind. A description of the current situation was compiled by mapping the internal runnings and material flow throughout the factory. A new suggestion for a layout and a comparison with the current situation will assist with creating a factual basis for the development of a new goods reception.A study was made where the volumes and the quantity of the daily arrival goods were settled.

Denna uppsats handlar om konkurrensmedel och hur en outlet arbetar med dessa för att påverka konsumenter i deras val. Bakgrund till uppsatsen är den starka konkurrensen som idag finns inom kläd- och varumärkesbranschen. I takt med att allt fler butiker öppnar sina dörrar intensifieras kampen om konsumenterna. Därför vill vi studera hur en Factory Outlet, som ofta saknar de fördelar, som till exempel en centralt belägen butik har, får konsumenter att välja just dem. Problemställningen som skall belysas är vilka konkurrensmedel en outlet har att jobba med och vilka de faktiskt använder för att skapa en alldeles unik mix som medför att konsumenterna väljer just dem.

This Master of Science thesis was a part of Pharmadule Emtungas project to construct a mobile automated cell for welding of carbon steel pipe (Heating, Ventilation and Sanitation). Pharmadule Emtunga is using a modular building concept for building pharmaceutical factories. The modules contain these pipes. The goal of the thesis was to present concepts for technical solutions regarding welding methods and fixtures for the cell. Conceptual models for the cell were made with aid of CAD software.

During 40 years of industrial production, from the end of the 1890?s until the end of 1930?s, coal and wood distillation products were manufactured in AB Carbo?s tar factory along the River Gimån in Grötingen, in the county of Jämtland, Sweden. In accordance with the Swedish Environmental Protection Agency?s Methods for Inventories of contaminated sites, MIFO, the site in Grötingen has been identified as a potentially contaminated site. In order to determine whether toxic substances pose a threat to human health and ecological systems in the area, there was a need to investigate the presence of contaminants, their levels and potential for migration.

Our purpose in this paper is to examine if there is any profitability for a company with a factory in the timber industry to invest in a combined heat and power, CHP. Based on analysis and the results that the paper generates, we will give Derome AB a suggestion on how it is a profitable investment or not to installing in a CHP.By investing in a CHP plant, you can get a high efficiency, which means that companies can use their resources more effectively. The Swedish wood industry has by-products of production that can be used for combustion in their boiler which is an advantage.The essay is a qualitative study where we have a case company, Derome AB. In this company, we interviewed two employees who have knowledge in the study. They have helped us to provide information and data about their business.We chose to use the pay-off- and the net present value method, NPV, to see if there are profitable advantages for the investment.

AbstractThis project is mainly focused on how the company OGO AB can organize its warehouse so that they can store painted articles.The warehouse should include how many pallets it is needed for the paint shop. Our purpose is also to calculate the space that is needed for the new warehouse.It is important for OGO AB to know witch kind of trucks they need for the new warehouse that with be located between the production factory and the paint shop so that the transportation of article goes smoothly..

At SIA TallOil's pellets factory in Latvia wood shavings and saw dust are dried with flue gases from a gas burner. TallOil wants to replace the gas with a biofuel that is available at the pellet plant. The reason for this is the unstable gas market in Europe in combination with the fact that TallOil wants to improve its profile as supplier of renewable bio fuels. In this project the technical and economical possibilities for a fuel conversion to ether bark powder, wood shavings or wood powder have been investigated. These fuels should be burned in one of the following applications: TPS BioSwirl, VTS Multifuel burner or Saxlunds bio fuel combustion plant Due to the fact that the fuel alternatives available are relatively common except for bark powder, the work has mainly been focused on bark powder.

In recent years, existing solutions for cooling personal computer CPUs have been supplemented by a new product category, factory sealed water cooling loops. These systems, consisting of a water block with an integrated pump, a fan and a radiator, perform well compared to the air cooling solutions but are less effective than larger, custom-built water cooling systems.This project aims to explore the most important aspects of a factory sealed system and to identify possible cost-effective enhancements of the performance.The most significant differences between the different groups of water cooling loops are the block design and the pumping power. The performance of both categories is also largely dependent on the fan power, but increasing fan power has a large negative impact on the noise level.Both radiator size and fan model choice appear, in tests, to be relatively unimportant, presuming that the noise level is kept constant. The position and direction of the fan, however, has significant impact on both the temperature and the sound level.Water blocks can be designed in several different ways, both regarding the heatsink design and the flow direction. In simulation, flow with the inlet centered above the heatsink result in considerably lower pressure drop and slightly higher temperatures than flow through the block, for heatsinks with fin arrays.Creating a competitive product in this product segment certainly seems possible, as there are performance-increasing changes to be made that seemingly has little impact on the production cost.

This master thesis encompasses an inventory of the older industrial community of Gimo. Investigations of the contamination situation for each industrial area were done. A risk classification according to the Swedish Environmental Protection Agency?s ?Method of Surveying Contaminated Sites?, phase one, followed. The risk classification was done on areas of Iron Work, a rockwool industry and a landfill. Gimo have had iron manufacturing from 1615 until 1945. Gimo have had two blast-furnaces and two smithies periodically.

För företag som arbetar med måttlistor och skisser och låter mönstret skapas på en fabrik kan det vara problematiskt att få plaggen att sitta som man vill. Speciellt svårt kan det vara med ärmhål, ärmkullar och halshål. Jag har arbetat med ett sådant företag för att ta fram en kappa och klänning från designskisser i sextiotalsstil med modern passform i storlekarna XS-XL. Moderniseringen innebär till exempel mer rörelsevidd, inte spetsig byst och längre ärmar. Till detta skapas plaggmåttlistor, materialspecifikationer och plaggdelsdokument för att plaggen ska vara färdigt för att produceras på fabrik.

Rimaster Kisa AB is a member of the Rimaster Group, the corporation was bought from Samhall AB in January 2007. The corporation is producing mechanichs needed by the Rimaster group as well for external costumers. Samhall AB is now functioning as a provider of labor for Rimaster Kisa, as the company is hiring personnel from Samhall AB. The company has earlier have had problems with their lead times being far too long. This has resulted in that the management decided to invest in a new edging press.

As a company it is required to work with strategies to minimize costs such as packaging and logistic costs. The increased market of industrial produced wooden buildings results that the time and the cost which the packaging of prefabricated building elements consume, is experienced to be in greater need of development than before and demands a better solution. The aim with this dissertation was to discover how the development of the handling of the packaging can improve the packaging process. The goal was to present improvement proposals for a simplified and thereby a more efficient production in time and cost perspective.The packaging process which includes packaging, handling, storage and transport were studied. Interviews were made with participants from the market for manufacturers of wooden houses and a case study was made at the company A-hus.

This essay is about Abrahams children and its teaching method  the IE- method. The purpose of this essay is to see what four teachers who use the method in their teaching think about it. To get an idea of how these teachers are working with the IE- method, I interviewed them. What are the pros and cons, is it a good way to teach religion? In addition, I look at how the IE- method follows the Lpo94 values and goals.

Considering that the current technology is constantly improving, it becomes increasingly important to have an efficient logistics in a company to maintain profitability while achieving a competitive business. Efficient logistics may be accomplished by improving the internal materials handling. In this thesis the internal material handling of steel frames has been studied at a factory in Vaggeryd. The goal of this study is to investigate the problems that exist with the current production flow of products and provide suggestions on how it can be developed to reduce unnecessary handling and movement.The study has a deductive approach where the authors has been using literature studies parallel with empirical analyzes conducted at a company to achieve the purpose of the study. Documentation from the company and interviews with staff and observations form the basis for the data collection carried out.

Chunks and Tasks is a programming model based on the C ++ programming language. This programming model is used for electronic structure calculations, among other things.The purpose of this project is to improve the CHT-MPI software library for Chunks and tasks, so that calculations of matrix-matrix multiplications are performed more efficiently than they do with the existing software library. The software library is based on the work stealing method, which is a method the software library for Chunks and Tasks uses for the distribution of the calculation work. The considered way to improve the software library is by modifying the work stealing method in a way that makes the distribution of calculation work happen in a more efficient way , which will lead to calculations performed faster than before.Two different modifications of the work stealing method were tested and it led to two new methods, Method 1 and Method 2, which distributed the calculation work differently. Method 1 did not give results that were compatible with the theory, since the calculation time with this method was much longer than the previous method.