This report aims to suggest recommendations that will increase the efficien¬cy in theconstruction process of a construction project. Through interviews, studies of budgetcalculations and examples given by the project management at the construction sightsan understanding of some complications have been gained. These complications havebeen tracked back in an attempt to find the source of the problem, and at the end ofthe report some suggestions have been presented with the pur-pose of preventingthese complications. Through the interviews it is suggested that many complications re-late to lack ofcommunication and motivation due to poor planning be-fore and during theconstruction process, a suggestion that is supported by the study of the budgetcalculations. The examples from the project management also points out someshortages in planning, but also coordi-nation related complications due to lack ofcommunication. To prevent these problems the recommendations suggested at the end of thisreport aims to improve the planning process through a properly fulfilledwalkthrough-planning of all of the construction activi¬ties during the time needed todo so. It is also suggested that the company uses experience from previous projects inorder to reduce costs, and that the qualifications of the employees is being appliedwhere it is needed.

This report investigates the possibility to use non-petroleum based adhesive (biobitumen) in asphalt. The main reasons for replacing bitumen are the fact that oil prices are rising, the threat of peak oil and the fact that the asphalt industry is becoming more environmentally friendly.The main purpose of this report is to investigate whether there are any non-petroleum based adhesives on the market. If so, how can they be used? The questions covered are:? Are there any other alternative asphalt coatings available?? Can bio-oils be used in asphalt?? If the bio-oils can be used, what are the details their properties?? How does a cold climate affect the bio binders?? What is the Swedish asphalt industry?s opinion about bio asphalt?The project was concluded through literature studies, consultations with people in the asphalt industry and through several interviews.The conclusion of this report is that there are some existing non-petroleum based adhesives on the market. They are mainly used for bike paths, sidewalks and parkareas.

The task given to us was to develop an industrial wheel with new thinking in terms of fresh design and construction, with the ability to brake. While the produced wheels of today only own the property of total braking, a wish was made to integrate the ability of directional locking.The time spent working with the project has been filled with multiple sketches of ideas and function analysis.Choices of material and ways of construction have been verified by calculations, tests and prototype building. The goal of this thesis has been to develop a unique caster with well thought-out design that would be adaptable to different areas of applications.The result was a hubless wheel with the ability of directional locking before total braking.A prototype of the wheel has been made to show the design and functions..

The background to this study is to find alternative ways of size rationalization. My vision is to take the basic conditions and make the best and most profitable of them. I have chosen press of rape oil because it?s interesting and the investment to get started is relative small. The opportunity to use outmoded and unrational buildings which often are found at many farms to something that gives money instead of costs money is also an argument.

The purpose with this essay is to give the reader an insight into and to describe the Danish Work Environment Act in its current wording and then compare it with the Swedish Work Environment Act. The first part of the essay describes the Work Environment Act and after that I compare with the Swedish Work Environment Act. At the end of the essay I will give my own thoughts of the result of this essay. I have chosen not to describe some of the chapters of the Act, for example the chapter about technical means and materials, because of the less importance for this essay and of my own interest. I have also chosen not to make mention of individual professions.

Choosing a new plastic material for a container includes several different steps. In this case,the Finnish company Hackman needed a new type of packaging material for theircutlery- and kitchentool series »Hackman tools«. The project was carried out in cooperationwith the design agency Ytterborn & Fuentes, which has Hackman as a client.Several different demands were put on the material in order to fulfill as many of the clientswishes as possible. The most urgent problem with the existing container was the difficultysfor the customer to clearly see the contents in the container. Because of this problemthe customer tried to open the container in the shop.

Our Bachelor?s Thesies has been performed in co-operation with Cellplast Direkt AB inLaholm. Our task was to develop a construction that cuts gussets to ceiling disposition as isused to isolation.Our goal with our construction was to increase the degree of automation so that theproductivity increased and also meet the market which is getting tougher and tougher due tothe future business cycle.Cellplast Direkt gave us free hands in order to enable new ideas. A pair different principleproposal was developed and prepared to a final structure.The Bachelor?s Thesies resulted in one PLC - governed machine with three engines that runthree different moves, wich does that the degree of automation increases and the risk forerrors decreases.We have developed a complete production bases to Cellplast Direkt and our hope is that thecompany comes to produce the machine in the future..

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

Titel: Investeringsuppföljningar ? En fallstudie på Volvo Construction Equipment i BraåsSeminariedatum: 2011-06-01Ämne/kurs: 2FE13E:3Författare: Aleksandar Stamenkovic och Donald BergströmHandledare: Anders JerrelingExaminator: Fredrik KarlssonNyckelord: Post-audits, Capital Budgeting, Investments, Performance Evaluations, ROI, RI, AARRSyfte: Syftet med detta ämnesfördjupande arbete är att förklara de problem som uppstår när avsaknad av investeringsuppföljning föreligger, samt att förklara för hur rutiner av uppföljningar kan organiseras.Metod: Valet föll på att göra en kvalitativ fallstudie gällande Volvo Construction Equipment i Braås. Kvalitativa semistrukturerade intervjuer har utförts med fyra stycken respondenter på anläggningen. Detta ämnesfördjupande arbete har utförts enligt en deduktiv metod och en diskussion förs angående arbetets validitet och reliabilitet.Teori: Den teoretiska referensramen behandlar relevant teori gällande investeringar och uppföljning, vidare behandlas även kortfattat de metoder som används för att bedöma investeringars lönsamhet på Volvo Construction Equipment i Braås.Empiri: Det empiriska avsnittet redovisar data från de semistrukturerade intervjuerna som fördes med personal på anläggningen i Braås. Dessa bestod av ekonomichefen, controllern samt två projektledare.Slutsats: Resultaten som presenteras behandlar komplexiteten med att följa upp investeringar enligt dess faktiska kassaflöden och förkastar därmed en sådan uppföljning för Volvo Construction Equipment i Bråas.

The purpose of this essay is to analyze and understand how producerbrands are able to communicate their brand through today's marketing channels, also how development and changes that occur in the society can affect the producers communication abilities. We have seen a tendency that many retailers have created their own brands that are competing with the producers, this leads to the fact that producers in some cases are having trouble communicating their brand to the end-consumer. The fact that the producers marketing through retailers now is more limited than before, the producers now have to capture the consumers wants and needs through other channels.This essay is based on a qualitative method involving seven interviews. The persons that we've chosen to interview are carefully selected based on their specific knowledge about the subject in question..

The economic analysis of building contracts is an unexplored field within Law and Economics. This paper makes an attempt to cast some light over the subject and encourage to more research within the field. The main purpose has been to describe why the actual price in a public construction project often turns out to be higher than the contract price and offer a way of handle that risk. In the paper a model is set up that shows an optimal contract given expectations on actual price and gaps in contracts. Cost increases for the buyer can mainly be explained by two situations.

Abstract This essay is about girls that have chosen a gender atypical education on a gymnasia level. Since we are living in a society that is still today gender segregated in both working life as well as educational area, we find it interesting that it still exist an paradox which leads us to the question ?why? those girls and boys, woman and man choose so differently. We are not aiming towards study how many girls that have chosen a gender atypical education but rather how these girls that are on the construction program in one of Stockholm?s gymnasium have deliberated and what it is that has influenced them.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

Examensarbetet är gjort för NCC Construction AB i Karlstad, all indata är baserad på NCCs tidigare projekt i Värmland. De flesta byggentreprenörer hyr sina etableringsbodar med vetskapen om att det kostar mer än att investera i bodar, men utan studier på att det är lönsammare att köpa bodarna. Studien är gjord på Cramos energieffektiva bodar. Energiförbrukningen för produktion av en byggnad uppgår till 15 % av byggnadens livscykel, vilket leder till stora kostnader. En stor del av energin i produktionsskedet går till etableringsbodarna, undersökningar har gjorts på bodar för att få fram en energieffektiv bod och därmed har utgifterna på etableringarna minskat. Det finns ytterligare ett sätt att spara pengar på gällande etableringen och det är att äga sina etableringsbodar.

The aim with this work is to understand and point out how significant Facebook is for teenager´s identity-construction. Through interviews with six teenagers, three boys and three girls in the age of sixteen and seventeen, I investigated how teenagers use Facebook and what purpose these interviewees put out to be members at Facebook.The interview-material then was analyzed from selected sociological/social psychology theories and also previous research. The study showed that the interviewees self-presentations for the sake of their awareness was more characterized of reflexivity than spontaneity. Because of their broad audience they choose to not write or publish too private information about themselves on Facebook. Despite a reflexive approach the identity-construction on Facebook could be affected of other people in a negative direction.