Cooling down the indoor air can be done in several ways. One way is desiccantcooling which will be used at the Stockholm Arena. This method is used in airhandling units that use temperature changes and moisture fluctuations in the air. Oneof the steps is to add heat during the cooling process in order to reduce the relativehumidity of the exhaust air. The air passes thru an adsorptions rotor which thenabsorbs moisture from the supply air.

Due to increasing regulations regarding new diesel vehicles particulate matteremissions the new Scania truck, Scania Euro 6, has been equipped with a particulatefilter. This component effectively stores the particles in the exhaust gas but must becleaned in order to prevent itself from clogging. The filter is cleaned through aprocess named regeneration which is a thermodynamic process in which thetemperature of the filter is raised through fuel supplied to the exhaust gas.The purpose of this thesis is to contribute to the development of improved controlstrategies of the temperature during the regeneration process through thedevelopment of model-based controllers. These controllers are designed in order tohave good performance in stationary as well as automatic regeneration.In order to develop these model-based controllers a model of the system isconstructed. The model is described as a linear thermodynamic grey-box model withflow varying parameters, showing good results in validation.The model provides a simulation environment during the controller design, which isfocused around the development of linear regulators with the exhaust gas mass flowas a scheduling variable whose size determines controllers? mode of operation.

The smelting process at Sapa Profiler AB in Sjunnen generates large quantities of waste heat which is absorbed by the cooling water when the aluminum is cooled down. This paper is the result of a Master?s Degree Project aiming to present the conditions for recycling the waste heat. The cooling water absorbs the heat from the aluminum at an average rate of 600 kW and the paper shows that it can be used to replace electrical power consumption for heating the production plant?s facilities.

At the moment in central Täby there are small district heating network operated by Fortum Heat. The distribution network has an annual heat demand of about 70 GWh, which is supported by the network's two plants, Galten and Farmen. Täby as a region is rapidly growing and there are grand plans to develop the area. Estimated market potential for a future district heating expansion in Täby is very high and as early as in 2007 Täby decided to invest in a large-scale expansion. In autumn 2009 Täby did a procurement process, known as the ?Täby initiative?, to find a partner that could implement those expansion plans. To secure a cheap basic production the partner also need to build a power plant at Hagby recycling center. Despite high interest during initial state of the process, only one procurement offer were received and Täby suspended the contract in March the following year.

Denna rapport har undersökt om game metrics genom heat maps kan användas för att hitta en choke point i en bana gjord till spelet Team Fortress 2. Game metrics och kvantitativa  metoder  erbjuder  ett  objektivt  och  nästan  automatiserat  alternativ  till kvalitativa metoder när det kommer till balansering. En bana har konstruerats med en choke point och har speltestats för att generera en heat map. För att undersöka om det går att hitta en choke point med hjälp av en heat map så har en enkät gjorts där respondenter   bads   hitta   choke   pointen   med   hjälp   av   den   heat   mapen   som genererades från speltestningen av banan. Alla respondenter lyckades hitta mitten av choke  pointen  med  hjälp  av  heat  mapen.  I  framtiden  skulle  arbetet  kunna  utökas genom  att  undersöka  om  användandet  av  bottar  eventuellt  skulle  helt  kunna automatisera  balanseringsprocessen.  Det  skulle  också  gå  att  undersöka  hur  olika klasser rör sig i en bana..

Due to increasing regulations regarding new diesel vehicles particulate matteremissions the new Scania truck, Scania Euro 6, has been equipped with a particulatefilter. This component effectively stores the particles in the exhaust gas but must becleaned in order to prevent itself from clogging. The filter is cleaned through aprocess named regeneration which is a thermodynamic process in which thetemperature of the filter is raised through fuel supplied to the exhaust gas.The purpose of this thesis is to contribute to the development of improved controlstrategies of the temperature during the regeneration process through thedevelopment of model-based controllers. These controllers are designed in order tohave good performance in stationary as well as automatic regeneration.In order to develop these model-based controllers a model of the system isconstructed. The model is described as a linear thermodynamic grey-box model withflow varying parameters, showing good results in validation.The model provides a simulation environment during the controller design, which isfocused around the development of linear regulators with the exhaust gas mass flowas a scheduling variable whose size determines controllers? mode of operation.

The exhaust arrangement on a Scania V8 consists of one manifold at each bank connected to a twin entry turbine (8-2-2). A study in GT-Power has shown improved performance and reduced cylinder to cylinder variations using two manifolds at each bank in combination with a single entry turbine (8-4-1). This thesis work analyses the difference in performance shown in simulation and verify it by engine test.The initial work was focused on simulation in GT-Power. Investigating how exhaust manifold volume and pulses effects the turbine efficiency and the mean effective pressure during the gas exchange. To verify GT-Power simulations four engine tests with different exhaust arrangement have been made.The results from GT-Power simulation indicate that a larger exhaust volume improve the turbine efficiency.

A Swedish electronics company wants to make the cooling of one of their electronic components more efficient. They propose that a retrofit liquid cooler is the way to achieve this goal. The current air cooling has high energy cost due to the high amount of power needed to power fans and heat exchangers. Using high volumes of air for cooling also leads to noise pollution. The conversion from air to liquid cooling would possibly make the operation of the electronics more cost efficient and less noisy.The purpose of this project is to theoretically evaluate different concepts of drawing the heat generated by the electronic component in to a fluid, using numerical calculations in Matlab and FEM simulations in ANSYS.

The present climate discussion has made energy efficiency an interesting topic. Saving energy does not only help the climate but also saves money for the energy consumer. The purpose of this thesis was to examine the potential of heat recovering from milk cooling. Two milk farms, one with voluntary milking system, VMS, and the other with conventional milking system was used to measure interesting temperatures and electricity consumptions. The numbers were used both to do theoretical calculations and to construct a SIMULINK model. To calculate the potential for heat at milk farms theoretical calculations were made in MATLAB using a reference farm with different combinations of heat recovery and pre cooling. The farm was assumed to keep a dwelling house with the annual heat consumption 18165 kWh.

 This degree project aims at developing a concept for how to use solar energy to pump up water. The target audience is people living in areas where the functioning of the electricity and water network is absent. In these areas, the hand-powered water pump is the most common technology. The degree project's goal is to find an economically viable alternative to the time consuming hand-powered water pumps. The power comes from solar energy.

When cows in Sweden are inseminated the heat strength is reported to the Swedish milk-recording scheme and AI scheme. Cows that show strong signs of estrus are desirable and the trait is included in the Swedish breeding goal. A strong heat makes it easier to inseminate at the right time and to avoid long and expensive days open. Since ten years the heat strength is scored from one to five by the farmer and reported to the milk-recording scheme and AI scheme. Earlier the score was from one to three and the decision was made by the AI technician.

Gunsta is situated about 10 km east of Uppsala. Today there are plans to establish 1000 new households in Gunsta before year 2030. The required energy for heating houses and water would be distributed via a district heating system, which also includes 200 existing residences. The annual required energy, according to this study, would be 16.2 GWh with a maximal peak effect of 6.9 MW. To meet this need, the study suggests a system with heat pumps to upgrade the 31?C water from a 1.8 kilometre deep borehole.

The urban heat island is an area restricted to a city center where the temperatureis higher than its surrounding environment. The greatest temperature difference isfound at night when the weather is calm and the sky is clear of clouds. There are twomajor causes behind this phenomena and the first one is the use of energy forheating of houses. The heat leaks through the walls of the buildings and warms upthe surrounding mass of air. The second one is the use of building material whichstore the suns radiation on daytime and releases the heat during night.

The purpose of this report is to investigate the possibilities with drain water heat recovery (DWHR) in residential buildings. Information and relevant theory has been collected and summarized in this report. Calculations have been done for given scenarios to evaluate profits. DWHR heat exchangers use simple technology and have long life-time. The heat exchanger is connected to outgoing drainage pipe and incoming cold-water supply so countercurrent flow is accomplished.

The Homogeneous Charge Compression Ignition (HCCI) engine is promising in terms of lowNOx, low particulates and high efficiency. Due to its homogeneous charge, where thecombustion starts almost simultaneously from a number of points in the combustion chamber,only lean mixtures are possible to burn because of the resulting rapid combustion, which is muchfaster than the combustion in an SI-engine or a diesel engine. When richer mixtures are used thecombustion will start earlier and also be more violent.To phase the combustion later and lower the combustion speed, external cooled EGR can beused. The EGR-system used in this thesis uses a divided exhaust channel where one channel andits corresponding valve are used only for transporting EGR back to the intake system.Consequently the EGR-valve is connected to the intake pressure. This system is called Direct-EGR (D-EGR).Engine tests verified that the CA50 indeed is phased later when cooled EGR is used.