The E-department at GETRAG All Wheel Drive in Köping have problems with the efficiency on parts of their production equipment. The equipment with the most significant efficiency problems are four automated multifunctional production cells that produces housing for rear drive units. The major part of the problem is the large amount of small stops that causes the low efficiency.The department already worked with logging of interruptions and efficiency calculations before this project started. However this work was not done to the extent considered necessary for a systematic follow-up of the interruptions.The aim of this paper is to point out a more effective and systematic way to work with logging of interruptions and the follow-up. In addition the equipment were studied with a method for efficiency calculation that ? if used properly- is a more powerful and a visually better method than the one used by the company today.As the initial current state analysis of the equipment was made a lack of documented knowledge about the equipment was discovered.

The environmental issues have during the last decenniums gained an increased role in both the political arena and in the market economy. The society is therefore more knowledgeable about the environment and our impact on it. Through this enlightened state, stakeholders tend to put pressure on the organizations of today. They, more or less willingly, incorporate this responsibility to be a part of their business. Entrepreneurs in the environmental area have seen this rising market as an opportunity to gain market shares and other positive outcomes.

During the autumn 2009, a 15 hp degree project was accomplished. The objective of the study was to describe different equipment alternatives, suitable for fresh market apple harvest. A field study was conducted during the harvest period to evaluate the efficiency (kg / person/ hour), using the different equipment. Four different systems are described in the study; Pick-ing-bag, Picking-train, Pluk-O-Trak and the Conveyor Harvester. The information about the systems is based on interviews with growers together with previous studies.

This bachelor thesis includes two different manuals and design of an interface box between a test object and a general test station (computer) with ARINC429 communication.There are three different purposes with this project:The first is to setup a general test station with ARINC429 communication using a communications card from DDC (DD-42916i3-300) and software from Ampol Technologies (dataSIMS).The second is to design a new interface between the test computer and the test object. As well as implementing two components in the equipment.The third is to write two separate manuals to guide the users of this equipment. There are two different kinds of users of this equipment, technicians and system engineers. Technicians use the equipment to test and repair flight components. System engineers will implement new components in the equipment.The result of this project is a working test station with a new interface and two manuals..

This thesis is a feasibility study into how Fresenius Kabi may rationalize their destruction process in regards to cost, recycling, and work environment. The two main objectives are to identify scrap flows and the possibility to improve or replace the equipment that is now carrying out the physical scrapping. The flow has been visualized by a flow chart of the material and communication. A chart of the problem established to visualize where improvements are necessary. Based on the problems proposals are presented on how to improve the flow thru the plant.During analyze of the physical scrapping equipment it was also necessary to take a deeper look at how they are carrying out there work today, how does the procedure look like, working environment and where are the weaknesses.

This paper is a study of documentary film production with focus on the filmmakers choice and usage of sound equipment. Using professional articles and literature have first of all helped us determine a standard for the conventional use of sound equipment in documentary film. Afterwards, by analyzing our own interviews we?ve received answers on how filmmakers relate to the conventional usage and why they select equipment as they do. Thereafter, we describe a technical method which helps a filmmaker to be able to record sound for documentary film on his/her own, using simple measures without reducing quality.

This paper is a study of documentary film production with focus on the filmmakers choice and usage of sound equipment. Using professional articles and literature have first of all helped us determine a standard for the conventional use of sound equipment in documentary film. Afterwards, by analyzing our own interviews we?ve received answers on how filmmakers relate to the conventional usage and why they select equipment as they do. Thereafter, we describe a technical method which helps a filmmaker to be able to record sound for documentary film on his/her own, using simple measures without reducing quality.

Physical rehabilitation is a constantly growing field in veterinary nursing. To build a physical rehabilitation center for dogs you need personnel with adequate education and knowledge. In spite of good knowledge it can be hard to know which areas and equipment necessary for the work. It is of interest to describe how a physical rehabilitation center can be planned and which spaces and equipment to prioritize. In this study, data of different spaces and equipment for a physical rehabilitation center for dogs are presented and also the economical perspective is introduced as a background.

At the Division of Electricity at UppsalaUniversitythere are ongoing researches, including a research concerning turbo generators.Turbo generators produce a large share of electricity in the world; however they are costly mainly due to the fact that the cooling and ventilation that are needed to eliminate the excess heat from the generators are expensive. Turbo generators work with high efficiency and in this project, the main task is to simulate a generator while taking into account that the generator must be designed against self-oscillation, centrifugal force, exhaustion and heat. The turbo generator must be simulated without being too expensive and complicated.In this project, the dimensions of the turbo generator depend on the efficiency of it, and where the losses are in the generator. Furthermore, the optimum values need to be chosen with the help of the ACE simulation program. The report begins with an introduction describing the project followed by a task description that is dealing with the project.

Compressed air is an energy source that is widely used in today's trucks and buses.Compressor located next to the engine supplies the pneumatic system with the compressed air and is lubricated with the engine oil. Some of the oil follows the air flow in both liquid and solid phase. The solid phase, namely the carbon particles are created due to the high temperature in the compression chamber.Oil- and particles carryover softens and destroys the rubber material in the air valves and disturbs the mechanical function of various components in the pneumatic system. In order to reduce oil- and particles carryover is an Air Processing System (APS) set downstream the compressor.No method for establishment of oil- and particles carryover from the compressor exists at the moment. Therefore the filtration efficiency of APS is currently unknown.

This thesis concerns an energy audit of a food industry. The company's business consists of boiling and peeling shrimps, and producing mayonnaise-based salads. This type of work involves energy-intensive processes, such as steam generation, compression of air and refrigeration of large spaces. These needs are supplied with electricity. Furthermore, the industry is a major consumer of district heating, particularly for heating the supply air in the ventilation system.

Traditionally, mining has been performed mechanically with implementation ofyesterdays (and older) data. Several mining companies have started to useautonomous technology and robotics in the production areas although the harshmining environments make it unsuitable for today's electronic equipment. Despite allthe obstacles along the way of digitization, there seems to be no end in sight as thisdevelopment continues. This thesis focuses on what the mining industry is aiming forand why the mining companies are interested in these technologies. The actors of themining industry can be found to have a vision for the future mine, a production with ahigher degree of digitization and resemblances to a factory.

In order to decrease the disturbance from a cable testing equipment, the company Ericsson Network Technologies in Falun determined to design a new series resonant test system with a lower frequency. The new equipment is of series resonant type with a system frequency of 500 Hz. This equipment consists of an inductor, a capacitor and a voltage source. The voltage source is the same as the old one, the cable acts as the capacitor but the inductor has to be designed especially for the new equipment. In this thesis work several air coil inductor types were examined.

The trotting in Sweden has a good reputation in an international view, both in the perspective of success and how the sport is managed with focus on security, animal protection and animal welfare. A large number of equipment details are fitted on the horses during training and competition. The Swedish law of prevention of cruelty to animals regulate training and competition with racehorses, and propose to protect horses from unnecessary suffering. The equipment permitted in races is regulated in Tävlingsreglementet (The Regulation of Competititon) and in the regulations of equipment, that the Nordic Regulation Committee and Nordic Animal Welfare Committee have worked out. Due to training and competition the equipment must even meet the Swedish law of prevention of cruelty to animals. However, the behaviour or the senses of the horses is often affected by the equipment due to the way the equipment corrects, modifies, restrains or reduces the behaviour of the horse, which may cause the horse stress or discomfort.

Many companies do not register all the stops that occur in a production plant, it often takes longer to report than to fix the problem. If no problems are registered, you cannot trace where the problems arise.This master thesis was performed at AcobiaFLUX and they have noticed an increased demand from their customers to trace problems raised in their processes. The aim of the thesis was to find out how a tool to monitor a process best could be developed. Then the most essential from the theoretical base was developed into a useful tool for operators. For the operators to know if the process utilizes the full capacity of a process, the tool presents a measure of the Overall Equipment efficiency, OEE.