Sydkraft Vattenkraft AB owns and operates the Traryd hydropower plant, located in the river Lagan in the southern part of Sweden. The gravity dam is classed according to RIDAS guidelines (Hydropower Industry Dam Safety Guidelines) as a class 1B dam. This means that the dam must discharge a class 1-flow which has a return period of 10 000 years. The inflow into the dam has been calculated in an earlier report to 495 m3/s, with a waterline at an elevation of 126, 3 meters above sea level. The gravity dam has a discharge system with two rectangular weirs, which results in a smaller discharge than the necessary 495 m3/s.

Natura 2000 is part of the European Union: s framework to protect and preserve biological diversity. Natura 2000- areas are by the goverment appointed to areas of national interest for preserving nature. Also wind power stations are appointed as of national interest and the reason for this is the goverments goal to get energy from reneweble energysources. This essay describes when both these intrests conflict eachother when it comes to building wind power stations within Natura 2000- areas. The main focus of this essay is a casestudy of two cases from two different counties, Dalarna- and Norrbotten county, where applications have been made to build wind power stations within existing Natura 2000- ares, both cases have reached the court dealing with enviromental issues.

Background:Life-cycle costing (LCC) is an investment calculation that takes intoaccount operating costs throughout the investee lifecycle. LCC calculations are mainly usedto evaluate investments that have no revenue side. Attempts to apply the LCC calculations forbuilding-related investments have occurred since the 1980s. Despite the advantages ofusing LCC calculations, use has not passed through in full. The main obstacles have beenidentified as a lack of relevant input data, and insufficient experience of workingwith LCC calculations.

The dependency of continuous electricity supply is high in the Swedish society today, at the same time no one is willing to pay for a too costly or over dimensioned power distribution system. The owners of the distribution systems are the ones responsible for this balance act of maintaining a high quality of electricity delivery to customers at a reasonable cost.In this master thesis a limited part of the primary distribution system (10 kV), owned by Mälarenergi Elnät AB and located in the city centre of Västerås, was chosen for a deeper analysis of its reliability. Its ability to handle outages of system components (N-1 and N-2 contingency analysis) was investigated to find out potential weak spots and parts of the grid that showed signs of being overdimensioned.The results of the performed simulations showed that in 74 % of the studied N-1 contingencies cases, consisting of outages of a bus bar in a distribution substation, the system could handle this without causing outages in other parts of the grid. For the N-2 contingencies 61 % passed the test. It was also found that one of the two included high voltage substations could alone supply the investigated part of the grid.

This thesis has been carried out in cooperation with Burseryds Bruk AB.Burseryds Bruk is a company that manufactures steel strapping. The thesis isabout developing a concept of protection that should be used to protect theoperators from the rotating parts of the machinery lines. The aim of the projectwas to improve work safety for operators working at the machines by producing aconcept for a protective device. The project's first part was based on ergonomic data collection methods tounderstand the operations performed on the machine and the hazard occurringduring the process. The methods used to collect data were, interviews,observations and questionnaires with the operators of the company. This was thenused to make the ergonomic analyzes hierarchical task analysis and link analysis. The data collected from the company's operators was used create 10 conceptswhich were then evaluated.

The thesis demonstrates a low-cost, low-bandwidth and low-resolution Analog-to- Digital Converter(ADC) in 0.35 um CMOS Process. A second-order Sigma-Delta modulator is used as the basis of the A/D Converter. A Semi-Uniform quantizer is used with the modulator to take advantage of input distributions that are dominated by smaller-amplitude signals e.g. Audio, Voice and Image-sensor signals. A Single-bit feedback topology is used with a multi-bit quantizer in the modulator.

Background:Life-cycle costing (LCC) is an investment calculation that takes intoaccount operating costs throughout the investee lifecycle. LCC calculations are mainly usedto evaluate investments that have no revenue side. Attempts to apply the LCC calculations forbuilding-related investments have occurred since the 1980s. Despite the advantages ofusing LCC calculations, use has not passed through in full. The main obstacles have beenidentified as a lack of relevant input data, and insufficient experience of workingwith LCC calculations.

This Masters thesis work describes a comparison between two different methods for estimation of the down channel (base station to mobile subscriber) in Wide-band Code Division Multiple Access (WCDMA). The first estimation method, Optimal Feed-forward Channel Estimation (OFCE), is a conventional method that bases the estimates on data that is known to both sender and receiver, so called pilots. The second method, Decision Directed Channel Estimation (DDCE), is an elaboration of OFCE. It also uses user data for estimation. Simulations show that DDCE, in comparison to OFCE, does not attain an improvement in signal-to-noise-ratio (SNR) for high bit error rates (BER). An improvement is only seen when the BER becomes much lower than what is common in real situations. In conclusion DDCE is complicated, involves many mathematical operations and gives insignificant improvement of SNR when BER takes common values. It is legitimate to question if it is possible to use the method in a real mobile phone system..

Den textila industrin, en egen värld, är nu under rampljuset som en av de största miljöpåverkande industrierna. Precis som i fallet med många andra industrier så måste textilbranschen intensivt arbeta med att minska sin negativa påverkan på miljön. Slutmålet måste vara att helt balansera uttagen och insättningarna så att man skapar en bransch som blir klimat- och miljöneutral. I denna rapport har en livscykelanalys gjorts på en underställströja från Helly Hansen tillverkad av 99 % polypropylene. Inom denna livscykelanalys har vi noggrant studerat och undersökt fakta för att hitta de processer som har den största påverkan på miljön.

LabVIEW ger en snabb och enkel tillgång till att styra instrument och en mycket stor databas med drivrutiner för DAQ-kort och olika datorgränssnitt (GPIB, serie, osv.).Många instrument och datorer kan anslutas till GPIB-bussen.  Detta kan ge en praktisk modell för utveckling av instrumentets styrprogram i LabVIEW med hjälp av GPIB-gränssnittet.Ett program i LabVIEW 8.2 med hjälp av GPIB-bussen kan kopplas till t.ex. multimetern (HP-34401A) för att mäta och visa multimeters noggrannhet. Men på grund av fel i drivrutiner för GPIB-gränssnittet kunde jag inte köra programmet med GPIB-bussen.Genom att använda LabVIEW 8.2 med hjälp av DAQ-kort kan en PID-regleringsalgoritm simuleras. PID konstrueras med virtuella instrument som innehåller alla nödvändiga komponenter och utrustning som krävs för att reglera någon linjär eller olinjär process exempelvis att nivåreglera två tankar i serie.

Background:Life-cycle costing (LCC) is an investment calculation that takes intoaccount operating costs throughout the investee lifecycle. LCC calculations are mainly usedto evaluate investments that have no revenue side. Attempts to apply the LCC calculations forbuilding-related investments have occurred since the 1980s. Despite the advantages ofusing LCC calculations, use has not passed through in full. The main obstacles have beenidentified as a lack of relevant input data, and insufficient experience of workingwith LCC calculations.

LabVIEW ger en snabb och enkel tillgång till att styra instrument och en mycket stor databas med drivrutiner för DAQ-kort och olika datorgränssnitt (GPIB, serie, osv.).Många instrument och datorer kan anslutas till GPIB-bussen.  Detta kan ge en praktisk modell för utveckling av instrumentets styrprogram i LabVIEW med hjälp av GPIB-gränssnittet.Ett program i LabVIEW 8.2 med hjälp av GPIB-bussen kan kopplas till t.ex. multimetern (HP-34401A) för att mäta och visa multimeters noggrannhet. Men på grund av fel i drivrutiner för GPIB-gränssnittet kunde jag inte köra programmet med GPIB-bussen.Genom att använda LabVIEW 8.2 med hjälp av DAQ-kort kan en PID-regleringsalgoritm simuleras. PID konstrueras med virtuella instrument som innehåller alla nödvändiga komponenter och utrustning som krävs för att reglera någon linjär eller olinjär process exempelvis att nivåreglera två tankar i serie.

Biogas is a gaseous fuel, rich in methane, produced through a biological route in an anaerobic digester. A gas engine generates combined heat and power, which can be used at the farm to reduce energy cost. The process also generates a digestate, with better utilization of nutrient compared to cattle manure. The aim of this study is to analyze the profitability of a farm-scale biogas plant for combined heat and power (CHP) at Wapnö. Wapnö is an agriculture company located in the southern part of Sweden.

We aim to investigate the risk exposure against commodity prices in the forestry and paper industry. The intension is also to study the affect that the changes in commodity prices has on a company?s market value..

Inom sjukvården används ? precis som överallt där människor sover ? sängkläder av hygienskäl. Problem med smittspridningar av typen multiresistenta bakterier (MRSA) och spridning av andra sjukdomar har drivit företag som Cellcomb i Karlstad AB till att utveckla engångssängkläder för att förhindra detta. Engångssängkläderna är skyddade av en biofilm som ska ge ökat skydd mot bakterier och fungerar som en barriär så att inte vätska tränger igenom. Problemet är att det inte finns mycket till underlag för hur engångssängkläderna står sig mot vanliga sängkläder ur miljösynpunkt.