To achieve the requirements to decrease emissions of greenhouse gases by 20 % by 2020, Swedenneeds to increase its use of bioenergy. In doing so it seems natural that those who already haveaccess to large amounts of biofuels in the form of by-products such as straw, wood chips anddigestible materials take advantage of these assets locally. By combining production of heat withpower production at the farm it may be possible to not only reduce the direct use of fossil fuel forheating but also reduce energy costs.The purpose was to simulate different cases of using a small scale biofueled combined heat andpower plant for farm-based systems. A MatLab-model was developed and used to draw conclusionsabout the costs for production of heat and electricity with different conversion technologies.The model uses climate data to simulate the variations in heat energy demand on a day-to-day basis.The given heat demand is the base of the simulation and from this the possible electric output iscalculated. This study has focused on the impact of the following properties: electric-, heat- andtotal efficiency, fuel, fuel price and specific fuel requirements.

The first part of this essay is about a single-family house that we have planned and projected. Thesecond part is a deeper study in ways to further insulate windows when they are not in use.In the first part the building?s design and its most important construction elements are described.The planning of all major installations (heating, domestic water, ventilation, sanitation, electricity)are reported so that one can in principle start construction of the house. In addition there arecalculations done on the building?s energy management.The result is a two stored house angled toward the south.

Svensk Växtkraft is the owner of the biogas plant in Västerås. The company is planning to increase their treatment capacity at their biogas plant. In connection to this work it is also possible to make some energy saving changes to the biogas plant. The objective of this study was therefore to make an electricity and heat survey of the biogas plant, a detailed study of the heat consumption in the sanitation step and also a comparison of energy consumption with the present sanitation method and an alternative strategy where the waste is treated in 55 °C during 10 hours (the current method is heating to 70 °C during 1 hour). The energy survey was conducted in close collaboration with staff at the biogas plant. The current during normal operation was measured, power was calculated and multiplied by the time of usage to obtain the energy consumed.

The municipality in Uppsala has set up goals for the future work concerning climate-and energy issues. As one way to achieve these goals the municipality started aproject called Uppsala climate protocol. During one of the project meetings anabatement map was presented. The map showed what savings in carbon dioxide andmarginal costs for different actions can be made. Statistics show that 40 % of thepopulation in Uppsala lives in a condominium.

The purpose of this thesis for Sapa Heat Transfer is to examine a furnace in which aluminium is pre-heated before hot rolling. The project is modeled in a computer environment in which the air flow in the furnace and the heat transfer to the aluminium solids are included. The computer environment and its governing equations, as well as boundary conditions and generalizations, are presented and explained.The simulations are based on two models. The first model has an asymmetric solid placement, which is how it looks in today's ovens. It is validated against collected data.

Sweden has long had access to low electricity prices due to the wide availability of hydro and nuclear power. This has now changed because of today's rising electricity rates resulting in increasing heating costs for properties, especially in the properties with electric heating systems."Ankaret" is a parish for "Svenska Alliansmissionen", which is located at "Gullbrannagården".The parish has installed electrical radiators and an exhaust ventilation system that makes the energy demand high due to the large ventilation flows. The building was built as the price of electricity was still low and would reduce energy use today by combining its heating system with an air/air heat pump. The heat pump delivers more heat into the room than the electrical energy that it uses. This lowers the electricity needs.

Arbetet går ut på att genomföra en miljö- och energianalys av två pressgrupper i processhallen. Detta innebär att dagens process skall analyseras för att se om man genom olika system kan göra arbetsklimatet bättre för operatörerna samtidigt som en besparing av energi möjliggörs..

The use of Power Line Communication, PLC, as a communication solution for Automated Meter Reading, AMR, is popular by utilities in Sweden and other parts of the world due to demands of accurate and fast meter reading. However the use of the electrical grid as a communication medium is complex and sometimes problematic. This report handles some of the issues and problems that are important to understand when using the grid as a communications medium. Focus is mainly on investigating high frequency distortion in the Kristianstad power grid own by C4energi caused by a frequency converter. Measurements on site are done to investigate signal damping in the grid, different configurations for the frequency converter and signal strength of the PLC-system.

The use of Power Line Communication, PLC, as a communication solution for Automated Meter Reading, AMR, is popular by utilities in Sweden and other parts of the world due to demands of accurate and fast meter reading. However the use of the electrical grid as a communication medium is complex and sometimes problematic. This report handles some of the issues and problems that are important to understand when using the grid as a communications medium. Focus is mainly on investigating high frequency distortion in the Kristianstad power grid own by C4energi caused by a frequency converter. Measurements on site are done to investigate signal damping in the grid, different configurations for the frequency converter and signal strength of the PLC-system.

This thesis has been written with our society?s current energy-situation in mind.Although it only deals with one particular block of buildings, the solutions and suggestions presented herein are quite applicable on other objects of the same type.This thesis is intended to be used as a guideline for energy-preserving projects in general, with an eye to buildings erected during the Swedish ?million-programme? in the sixties and seventies.The paper starts with the acquiring of all necessary blueprints and technical specifications. It then moves on to a thorough description of the buildings in question, and their heating- and ventilation-systems.Followed by this the reader is guided through the successive stages of energy-perseverance measures that are available, and possible. Reasoning around the economic factors concerning all measures is also held.The paper ends with conclusion, and a discussion concerning the delicate issue of the higher return-temperatures possibly reaching the district-heating plant..

Uppsala County has ambitious environmental aims for the planned residential area inÖstra Sala backe. In this thesis different energy sources have been evaluated todetermine which system that would be most favorable given currently availableinformation about the project. Planned energy usage has been divided into tap waterheating, space heating and power. Three base case scenarios were made with districtheating, small scale bio fuel and heat pump. Solar power and solar heating were thensimulated and the production from the two could individually be deducted from theenergy need in the base cases, constituting 9 different scenarios.

The building sector accounted for around a fourth of the total energy usage in Sweden in year 2010 (Energimyndigheten, 2012). Therefore it has become very interesting to achieve a lower energy usage in residential buildings. One way to achieve that is to build so called passive houses. By being very well insulated and have low leakage through the walls, they can reduce the energy usage for heating with a substantial amount. The first passive house was built during the 90?s in Germany; and in Sweden the first passive house was built in Gothenburg 2001.

This master thesis is an in-depth study of an existing heating system at a household cooperative in Uppsala that has been converted from district heating to a bedrock heat pump system. The study focuses on an economical system optimisation of the building?s complete heating system. The aim was to determine how well a heat pump system in large buildings actually work, find out possible ways to optimize the existing system and point out important system parameters for new heat pump installations in larger buildings.The project points out a possible energy cost reduction of 45 % without investment and further cost reductions with equipment investments. A reduction by 30 % is possible by improvements in the regulation system and 15 % is possible by maintaining the brine system.

This master thesis work was done at Saab Underwater Systems AB, a company at the cutting edge of underwater technology. Here torpedoes and other underwater vehicles are developed and manufactured. The major customers are navies of different countries, mostly the Swedish navy. The aim of this master thesis is to develop, construct and evaluate an automatic Trim System for Unmanned Underwater Vehicles. The task of the system is to change the position of the centre of mass and the vehicle?s total mass or volume.

The purpose of this degree project was to build laboratory equipment for a new course in power electronics that starts this autumn 2010 at Uppsala University. The equipment is intended for student labs and it covers the most important areas of the course including rectifying, buck-/boost-converters and PWM-modulation. It is built as one sealed unit where all the electronics are built-in but visible and it has a connection board where students safely can connect the different circuits. The project has advanced from theoretical studies of circuit design, choosing of components and simulations to drawing the printed circuit board (PCB), soldering, case building, final testing and troubleshooting - basically most steps from an early idea to a final product. Measurements on the final product gave about the same results as the earlier simulations of the circuits and the result is overall satisfying..