The student project Elba at KTH started in 2011 and is a project where a battery driven prototype car is developed. The vehicle competes in Eco Shell Marathon in Rotterdam, Holland. In this competition the vehicle that travels a certain distance including several starts and stops with the lowest energy consumption wins. To minimize the consumption is therefore very important, which requires knowledge of the vehicles energy losses.A vehicle's energy losses depends on several factors and can be divided into the powertrain efficiency and the driving resistance. The driving resistance can then be divided in to rolling and air resistance, if smaller losses like vibrations are ignored.

WSP building physics in Stockholm has certified the preschool Temmelburken in Bromma with the system of certification Miljöbyggnad. The rating of the building became BRONZE. In this thesis the preschool has been investigated with respect to the three areas: thermal climate, use of energy and improving of the level of certification. The thermal climate at the preschool has been investigated by a questionnaire survey and by measurements in order to do comparisons between the results from the two investigations as well as with the results of the simulations that WSP has done at the certification of the preschool. The differences between the results from the simulations and the questionnaire survey for winter as well as from the measurement performed with a comfort meter the 19th of March are concidered to be reasonably small since they give rise to the same rating according to Miljöbyggnad.   Operational data for the use of energy for the preschool have been obtained in order to do comparisons with simulations performed by WSP and Svenska Besiktningar AB. The comparison shows that the simulated values for the specific use of energy are lower than what the real specific use of energy would be for the preschool, since just the operational data for the heat energy is higher than the simulated values. At the investigation of the possibility of improving the level of certification it was found that the rating of the preschool can be raised from BRONZE to SILVER by improving the ratings of the ?thermal climate summer? and the ?daylight?.

AbstractThe indoor environment affects the human performance. Noise pollution, poor lightning and coloring are some of the factors that affect our work performance. The human is also affected by the air change and temperature, these factors are in most buildings possible to adjust and through this make economic savings. To find out about the indoor environment in the O-building a questionnaire was handed out, measurements/surveys and an interview was also made. 108 questionnaires where handed out to employees and students.

Due to higher standards of living around the world, greater industries and larger infrastructures causes an increase of the global energy consumption. This harvest of energy puts a great stress on the global environment. With this development, it becomes increasingly important to utilize energy resources in the best possible way.Fans are components that are often used in the industry and in households. A common problem is that the fan is oversized. An oversized fan causes an excessive flow, which has to be adjusted in order to achieve the correct flow.

This report is about helping Q-Med AB in Uppsala to start its implementation of uncertainty of measurements analyses in their manufacturing department. Prior to this, the company relied solely on personal experience or did not take this uncertainty into consideration at all during different kind of measurements, which means that some of the processes that the company previously believed were within specified acceptance limits, will actually fail when considering these sources of uncertainties.Q-Med AB needed some sort of instruction to help the company, in a systematic way, to investigate different types of disorders that are affecting all kinds of measurements. This instruction includes a short summary about measurements and uncertainty of measurements in general and a detailed procedure about how these uncertainties are going to be handled in their daily work.The goal was to be able to use this instruction to systematically locate, eliminate (when possible) and analyze all kinds of disorders when measuring. Q-Med is using a lot of different types of instruments when measuring different types of quantities, including temperature, mass, pressure and density. This instruction will hereafter be used for every instrument, regardless of quantity and type of instrument.The instruction is tested through 4 different kinds of measurements, for mass, temperature and humidity.

ABSTRACTThe discussions about energy use have increased year by year everywhere in the society, and so also in the healthcare sector. But what is actually energy use in a hospital facility, and what affects it?The typical way today to express the energy use is in kWh/m2. The problem with a key performance indicator that is expressed as energy use in relation to a specific area is that it does not take into account the activity in the building. Even though the activity to a very high extent affects the energy use.

ABSTRACTThe discussions about energy use have increased year by year everywhere in the society, and so also in the healthcare sector. But what is actually energy use in a hospital facility, and what affects it?The typical way today to express the energy use is in kWh/m2. The problem with a key performance indicator that is expressed as energy use in relation to a specific area is that it does not take into account the activity in the building. Even though the activity to a very high extent affects the energy use.

The regulations for energy consumption are consistently getting more and morestrict. This leads to a higher customer demand for energy analysis early in the buildingdesign process. Many building planners and architects use powerful modeling softwareto visualize their projects. These digital models contain sufficient information aboutthe building?s physical characteristics for reliable energy analysis.

A large proportion of the energy consumption is in the building industry and a large part goes to heating our homes and premises. In the developing countries' development now threatens the large consumption of energy in our earth's climate. It is in the West world that we must be good role models in terms of energy efficiency. One solution to reduce energy consumption for heating of buildings may be to continue to build low energy houses and passive houses, but it is also about rebuilding the buildings that currently have high energy consumption such as the old Million program Houses. These buildings will be standing many years and their energy consumption will not diminish over time by itself and energy prices will certainly not diminish in the future.

ABSTRACTThe discussions about energy use have increased year by year everywhere in the society, and so also in the healthcare sector. But what is actually energy use in a hospital facility, and what affects it?The typical way today to express the energy use is in kWh/m2. The problem with a key performance indicator that is expressed as energy use in relation to a specific area is that it does not take into account the activity in the building. Even though the activity to a very high extent affects the energy use.

Drain water heat recovery is an uncommon measure in multi-unit residential buildings. There istechnology available for the purpose but the knowing and experience of the heat recovery systems islittle. The purpose of this thesis is to evaluate the future potential of drain water heat recovery inmulti-unit residential buildings.A major part of the multi-unit residential buildings in Sweden were built during modernismen andrekordåren (1940?1975). Many of the buildings have worn out drain and water supply systems andmany are in need of a general refurbishment.

This report is about helping Q-Med AB in Uppsala to start its implementation of uncertainty of measurements analyses in their manufacturing department. Prior to this, the company relied solely on personal experience or did not take this uncertainty into consideration at all during different kind of measurements, which means that some of the processes that the company previously believed were within specified acceptance limits, will actually fail when considering these sources of uncertainties.Q-Med AB needed some sort of instruction to help the company, in a systematic way, to investigate different types of disorders that are affecting all kinds of measurements. This instruction includes a short summary about measurements and uncertainty of measurements in general and a detailed procedure about how these uncertainties are going to be handled in their daily work.The goal was to be able to use this instruction to systematically locate, eliminate (when possible) and analyze all kinds of disorders when measuring. Q-Med is using a lot of different types of instruments when measuring different types of quantities, including temperature, mass, pressure and density. This instruction will hereafter be used for every instrument, regardless of quantity and type of instrument.The instruction is tested through 4 different kinds of measurements, for mass, temperature and humidity.

The acoustics in a control room is a complicated phenomenon. Early reflections, reverberation time and area in the room are some of the problems. This report is about the reflection on the mixing console in a control room. The control room being built, these reflections are difficult to take into consideration since the mixing console is one of the very last items you place in the room. This report will explain three main measurements that were done in order to get the answer to the following question: Does the mixing console interfere the frequency curve at listening position? Three measurements were done and the difference between the measurements was that the microphone and the loudspeakers were placed in different places in the control room.

Energy costs are high nowadays and that is the reason why the energy consumption needs to become as small as possible in most of the companies. To accomplish the small energy usage one needs to map the energy flows, study them and monitor them. One method that can be used for this is energy balance calculation. The method gives an opportunity to separate different energy flows and see where each flow is heading. There is also another method which is more advanced than energy balance calculation.

The Swedish building stock accounts for nearly 40 percent of the total energyconsumption in the country. Properties built today are likely to last for 100 years orlonger. This places high demands on long-term and smart energy solutions that willkeep the future Swedish building stock energy consumption at low levels. This thesishas focused on examining how the energy performance of buildings is affected bydifferent choices of window types in different cardinal directions. The objective wasto obtain a basis for recommendations on how window properties can be optimizedfor different types of buildings and orientations.