Future emission legislation puts great emphasis on increasing the efficiency of the engine, thereby reducing fuel consumption. The tribological contact between cylinder liner and piston ring is where an great amount of energy is lost due to friction, and by reducing these losses an reduction in fuel consumption can be achieved.The aim of this thesis was to evaluate the tested piston ring coatings against a plasma sprayed cylinder liner and rank these combinations of materials for friction and wear resistance. The coatings that were tested was Cr + Al2O3, (Al,Cr)N, two types of CrN and WC / C.The experimental tests were performed with a so-called pin-plate, where used oil with addition of an acidic mixture of sulfuric and nitric acid to mimic the acidic condensate formed when exhausts recirculate, were added with a continuous flow. The results were then analyzed by weighing, studies by optical microscopy and scanning electron microscopy (SEM) and profile measurements.The results from each material combination were that the plasma coated cylinder liner wears too aggressively in order to yield a ranking of the piston ring coatings based on the parameters of friction and wear resistance. It is therefore proposed that an alternative coating on the cylinder liner should be developed, lacking the large abrasive wear on piston rings and that can withstand the corrosive environment resulting in engines equipped with EGR.

Organisation and market orientation of elderly careThis comparative literature study is intended to describe how elderly care is organised and financed in Germany and Sweden. Furthermore, it analyses the degree of competition and market orientation in both countries' care systems. Important aspects in this context are the kinds of measurements which are used on the two markets and the question if there are quasimarkets.The theoretical backgrounds of the study are Esping-Andersen's "Three Worlds of Welfare Capitalism" and Harold Wilensky's convergence theory. Esping-Andersen's theory describes Sweden as a social democratic and Germany as a conservative welfare regime which means that there are different conditions for the development of welfare. The use of Wilensky's theory shows that both welfare systems are converging since the end of the 20th century.

The wind power increase of Gotland as well as other parts of Sweden during the last ten year period has meant that this renewable energy source has increased its share over other fossil sources. The year of 2011 became the first when the wind power produced more energy than an average nuclear reactor. Now that wind power is in an expansive phase, the land issue will be of great interest. Land with good wind resources will be of interest to wind energy developers. The problems that this essay is based on are; how can landowners altering the economic conditions at a wind power establishment? What opportunities and obstacles exist for landowners who choose to set up wind power on their land? The purpose of this essay is to highlight the economic conditions that exist for landowners for the establishment of wind farms, with regard to compensation for the leasing and return on invested capital.

En jämförelsestudie har genomförts mellan två värmesystem. Analysen har genomförts med ett flerbostadshus som referensfasighet. Fastigheten är lokaliserad i Södertälje kommun. Analysen går ut på att bestämma vilket värmesystem som är fördelaktigt vid renovering av äldre flerbostadshus med avseende på energi och kostnad. De systemen som har behandlats är ett centralt värmesystem med motströmsvärmeväxlare och ett centralt värmesystem med frånluftsvärmepump.Det centrala värmesystemet (Eq aggregat) är ett centralt från- och tilluftssystem med återvinning (FTX system).

Periods of hypoxia are a recurring issue in Brunnsviken. Main factors that trigger hypoxia in Brunnsviken are eutrophication  due to anthropogenic emission of nutrients, stratification in the water column due to salinity and temperature differences  that prevents mixing and a sill inlet that prevents water exchange. As an attempt to improve the oxygen levels, bottom water is pumped from Brunnsviken causing aerated surface water to flow back into the basin.  The objective of this Master?s thesis was to study the change in dissolved oxygen levels due to pumping.

Lumilos is a work investigating the possibilities to use light and color in an interactive design context. I have explored different light sources and compared them to each other and given a short description of the history of light and how it has been developed during the industrialization in the western world. I have also investigated what is currently done in the field and summarized that with examples in the categories passive-, colored-, material- and interactive light. The conclusion is that working with interactive color and light is a hard task. There are many different angles to take into account such as personal likings and earlier experiences that is uncontrollable by the designer. Yet there are many possibilities and light is a material that is moldable in many forms. I have put the knowledge about light and color into practice and developed an interactive light wall that is visualizing energy consumption with the use of different colors of light and animations.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

During the late twentieth century, political and societal changes gave rise to an increased interest in performance evaluation in public organizations. This development also affected libraries in the public sector. The main concern for this master thesis is performance measurement in libraries. In this study two different types of libraries are investigated, one public and the other academic. My aim is to find out if and how performance measurement appears in the libraries annual activity reports.

In the spring of 2014 Sweco Systems AB were commissioned to design a ventilation system for a newly built preschool in Linköping. Terms from the client was that it cost efficiency would cope with the energy demands that are placed on the building. The unit chosen was a cross-flow heat exchanger, and this work is to compare it with two other heat exchangers to see if a more energy and cost efficient could have been chosen. The heat exchangers that was chosen for the comparison was a rotating- and a counterflow heat exchanger. Simulations have been made to the different heat exchangers by the manufacturers.

The third most common conifer in Sweden is Pinus contorta (lodgepole pine). It originates from the western part of North America and was brought here in the end of the 1920s. The lodgepole pine is today allowed for commercial plantations in central and northern Sweden, excluding high altitude locations. Since 1979 only plantations with scientific purpose are allowed in south-central and south Sweden. This document is focused on how lodgepole pine manage perform compared with Pinus sylvestris (Scots pine) in the southernmost part of Sweden, Götaland. The idea came from the fact that the Swedish government is evaluating a notification from the National Forest Agency that suggests lodgepole pine to be allowed for commercial plantation even in southern Sweden.

When the Swedish Forestry Act was changed in 1994, brushing of young stands became non mandatory. Since then the annual need for brushing in the country has increased by about 100 000 hectares per year. In later years the price for biomass energy has increased to the same level as pulp wood. The high price on biomass energy and the large areas of stands in the need of brushing has created a new market with its own technical, economical and environmental conditions. There is a development of various techniques to manage the forestry stands with late brushing.

The purpose of this degree-project was to investigate the possibilities for primary air preheating into the two smallest waste incineration boilers of Halmstad Energy and Environment. The investigation is a pre-study which has the primary goal to evaluate technical and financial offers from companies that manufacture primary air preheater, and investigate if it is technically and financially profitable to do a purchase on primary air preheaters in the future.In the pre-study it is proposed that it is most efficient to have individual primary air preheater, one for each incineration boiler and the primary air are also proposed to be preheated by hot water in the pre-study. Further in the pre-study it is proposed that the heat-exchanger should have plain tubes instead of finned tubes, to avoid getting dirty fast. The space in the boiler-room is limited, and therefore the major problem was to fit in the primary air preheaters into the boiler-room. By comparing the different offers from the companies, the result in the pre-study shows that the offer from the company C.A.

This report is part of a Bachelor?s degree corresponding to 15 creditsat the Royal Institute of Technology, Stockholm. The work hasbeen carried out by Max Wikander, author of the report, supervisedby Lanie Gutierrez-Farewik and Erik Dijkstra.Gait analysis includes measurement, characterization and assessmentof human movement and is used to assess kinematic or otherabnormalities during gait. Center of rotation and the axis of rotationof a joint are fundamental parameters in motion analysis. However,the ability to create individualized analysis is limited by the lack ofaccuracy when these parameters are calculated.

Lars Höglund AB is one of Scandinavia?s most qualified manufacturers of sheet metal products and provides custom designed products of very detailed precision. One of the main methods of manufacturing is laser cutting. When Lars Höglund AB signed up a new customer, with high demands in tolerances for the products, Lars Höglund AB thought it would be necessary to know the capability of the laser cutting machine. Also the process of how to retrieve this capability was interesting. The capability will be researched for the following elements: Cutting right angles in squares with a corner radius of 1 mmCutting corners which are not right angleCutting of circles with constant radius Measurements were made on 150 pieces of sheet metal details, which had been cut out by the machine.  The data from the measurements where later used to study the capability.