In cooperate with Asko Cylinda we have developed a new heat system too short the process time and reduce the energy consume in a dishwasher and still have it too be a class AAA. The environment and quality is important for the company too still be the number one on the market, If they want too keep that position the product developed of new innovations will be very important. The systems we have developed are more effective and reduce energy up too 25 %. The process time is reduced too less than two hours, from the today two and half-hour. The solutions are too heat up the rinse water and the dishwater at the same time, with a new heating system and it make are solutions unique and effective. Its good for the dish and the environment.

Buildings worldwide account for 40 % of the total energy use. Climate change is of increasing importance, but few are willing to reduce their standard of living or get a higher cost for the change. Energy efficiency of existing buildings gives the greatest benefit economically and environmentally. The real estate company Klövern AB manages 46 properties in Karlstad. Heating is the major cost of the total operating costs of real estate. Rising energy prices increase the need for Klövern AB to improve energy efficiency and to investigate alternative sources of heat.

The concept of green IT is a hot topic in the industry right now. The requirements forenvironmental friendliness are becoming increasingly common. There is a lack of knowledge andunderstanding of what green IT means and how it can be achieved. Our study shows that the useof ICT can never become entirely green, but a lot can be done to become greener. We haveproduced a balanced scorecard which in theory leads to better governance, increased knowledgeand a common picture of what the work of greening IT means for employees and theorganization.

Husums plant has a selection of different pulp pumps at bleaching plant 4 and 5. The displacement- (HC-pump, Sund Defibrator PTD-60) and centrifugalpumps (MC-pump, MCA 42-200, MCP 30/20) are of interest in this report. The centrifugal pumps are controlled by throttle valves, which result in an energy loss. Chemical mixers are used to mix ClO2 into the pulp before proceeding into a holding tower where the bleaching process occurs.The energy demand of the different positions has been measured or calculated to be used in comparisons against new equipment. Quotations were requested and delivered from Valmet and Sulzer.

Mobile technology is developing quickly and becomming a part of daily life and communication. Bluetooth Low Energy is presented as a new way of mobile interaction. However there are not enough studies in this field on the interaction between mobile devices and the physical world. In order to understand user needs, and to encourage users to interact, we simulated an interaction process through designing and testing a prototype in a specific indoor environment. Prototype effectiveness and main characteristics for future mobile application was evaluated through a qualitative user study with 20 participants who interacted with our prototype..

This project investigated the current market regarding wireless net and the communication between the tools used for diagnostics/maintenance and an embedded system. Based on documentation obtained through interviews a demo system was created based on Bluetooth Low Energy (BLE) communication between an embedded system and an Android device.This report intends to describe the tools and methods used in the design of the demo system and the result of an analysis of the BLE communication.Bluetooth Low Energy is an exciting protocol with wide applicability within the industrial field. This project investigated the communicational possibilities between a Smartphone and a Raspberry Pi and based on the results that emerged the conclusion can be drawn that BLE is a protocol with many beneficial applications within industrial IT..

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area. The results show that use of locally installed renewable energy sources can reduce the total climate impact when life cycle perspective is applied.

The Swedish automotive industry has since way back been struggling with bankruptcy, abroad buy outs and staff cuts. Competition and pressure on prices are two factors that affect the automotive industry. Because of this, the companies are pressured to continuously developing their work in addition to be able to compete on the market. The aircraft industry has successfully managed to implement additive manufacturing (AM) and for motorsport has several components manufactured with AM been used. When AM is used as a manufacturing method, there are a number of advantagesthat follows.

To achieve a sustainable development, three aspects have to take equal place in the society; environmental, economical and social. To reduce the impact on the environment and the amount of greenhouse gases supplied to the atmosphere, industrialized countries and less developed countries must start cooperating. Also the use of renewable energy sources, like solar, hydro and wind power, have to increase.Wind power has great potential as a future energy supply. It is cost efficient, quickly developed and the resource is abundant and available worldwide.Examinations made in Sweden, indicates that there are difficulties establishing wind power at the same pace as the environmental goals, set by the Swedish government, requires. Mainly because people living nearby potential areas for wind power farms, appeal against the decision.This study aims to investigate differences between how people in Sweden and Brazil look at wind power as a future energy source and at the establishing process.

Umeå Energi are working towards a goal, that in the year of 2018, they will be completely climate neutral. As a part of this, one target is to reduce their grid losses by 4 % of the 2012 level, which corresponds to an overall reduction of the grid losses of just over 1.7 GWh. In many residential areas, the distribution grid is designed and rated for electric heating as the heating in the houses. As many of the houses later has been converted to other types of heating, their electricity use has decreased and the total power output from many of the secondary substations has decreased significantly. Because of this, many of these stations today are well oversized, which in turn means that the energy losses in these stations are unnecessarily high.In this degree project, 25 secondary substations have been studied, all located in residential areas in and around central Umeå.

Den här rapporten har skrivits som en del av ett examensarbete på energiingenjörsprogrammet på Högskolan i Halmstad under våren 2014. Examensarbetet har genomförts i samarbete med AB Färdig Betong samt ÅF Infrastructure AB i Göteborg.Syftet med projektet är att undersöka energibesparingspotentialen hos AB Färdig Betongs produktionsanläggning på Ringön i Göteborg.Projektet har inneburit en energikartläggning av en industriell produktionsanläggning för lösbetong. Utgångspunkt för energikartläggningen har varit energiledningssystemet ISO 50001, med målsättningen att ta fram en teknisk energikartläggningsrapport i enlighet med standarden.Anläggningen har analyserats ur ett energibesparingsperspektiv. Data- och informationsinsamling samt mätningar har genomförts för att ta fram indata som beräkningsunderlag. Genom beräkningar har sedan möjliga energibesparingspotentialer och åtgärdsförslag tagits fram.Den totala energibesparingspotentialen för anläggningen innebär en besparing på 223 MWh av anläggningens totala energianvändning på 857 MWh år 2013, vilket motsvarar en minskning med omkring 26 %.Allmänna slutsatser är bland annat att all produktionsutrustning bör placeras inom klimatskalet, att all uppvärmning bör vara temperaturreglerad samt att ett mer långsiktigt energiperspektiv behövs i anläggningen.Energibesparingsmöjligheterna för anläggningen är mycket goda och investeringskostnaderna är i allmänhet låga..

Corporate Social Responsibility (CSR) is a topic that is becoming increasingly important in today's society. CSR is a concept whereby companies voluntarily integrate social and environmental concerns both in their business but also in interaction with their stakeholders. The society of today sets high expectations for how companies take their social responsibilities, especially in industries where the risks to individuals and the environment are high. In this study, we tried to answer the following questions; what kind of responsibility do companies in the plastics and chemicals industry claim to take and why might this be due? What differences exist between the investigated companies in the industry and what may these differences be rooted in? The purpose of this study was to obtain an understanding of the interest in working on sustainability in the plastics and chemicals industry.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area.

ABSTRACT The purpose of this medical record research was to study 30 patients with chronic subdural hematoma on a neurosurgical clinic, mapping documented nutritional status, preoperative fasting and hydration and energy supply before surgery. In addition peroperative administration of fluid and vasoactive drugs, as well as postoperative complications and length of hospital stay were studied. The mean age of the patients was 71 years. Nutritional status was evaluated in 12 patients, out of these seven were judged to be at risk for under nutrition. Fifteen patients had surgery day 1 (total fasting time on average m 11 h), eleven had surgery day 2(29 h), three had surgery day 3 (35 h).

Since a few years back television has been on a verge of an enormous digital change. Web-TV is now growing at an incredible rate and is said to completely change the way we consume TV. The purpose of this essay is to determine and gain an understanding of how representatives of the broadcast industry looks at the phenomenon of web-TV and especially the different kinds of online video services and how they believe this will affect the television. Methods used are qualitative interviews which we compared with previous studies on the subject and acknowledged communication theories. The respondents were people with good insight and understanding of the media and TV industry.