Sambandet mellan samhällsutvecklingen och de växande miljöproblemen kom i slutet av 1980-talet att få en allt mer framskjuten roll på den politiska agendan i Sverige. I och med att energianvändningen står för en stor del av miljöproblemen har allt fler kommit att inse vikten av att uppnå en hållbar situation för energianvändandet. För att se hur arbetet mot en hållbar energianvändning fortskrider har International Atomic Energy Agency (IAEA) tagit fram en modell för detta. Studiens övergripande syfte har varit att analysera huruvida Sverige går mot en mer hållbar energianvändning med hjälp av IAEA:s indikatorer. Teorin i studien har baserats på grundläggande miljöekonomiska resonemang.

An increased awareness about the global warming has created a demand for more information on how the climate is affected by different activities.This master thesis was initiated by Tricorona, a Swedish company that offers its customers analysis and calculation of their climate impact. Tricorona also supplies climate neutralisation with CERs, in accordance with the Kyoto protocol and controlled by the UN. This work demands updated emission factors for greenhouse gases. An emission factor gives information about the greenhouse gasintensity of a service or a product [kg CO2-eq./ functional unit].The purpose of this thesis is to examine how electricity, district heating, hotels, taxis, food and materials affect the climate and how emission factors for these areas can be calculated.This was done by reviewing and comparing different studies and by interviewing experts. The information was evaluated and recommendations on calculations and emission factors were made.The consumption of energy is the main source of greenhouse gas emissions for district heating, electricity, hotels, taxis and materials.

This project is about a transformation of an existing factory in Paraguay to a local sustainable refinery. The project aims to combine local knowledge and material and modern but low tech technology, this in combination with a contemporary form and new use of bricks in Paraguay..

The aim of the present study was to investigate the effect on growth of foals on two different diets, either a forage-based diet or a diet containing approx. 40 % concentrate. The report also includes a review of the pertinent literature on the effects of diet on mares? milk and growth of horses. The hypothesis of the study was that a forage based diet will result in a similar growth pattern as a diet including more concentrates if the diets contain the same amount of energy, crude protein, lysine, calcium and phosphorous.

In this Thesis the possibilities of designing a larger building that is very energy efficient in the sense that it would not need a conventional heating system are discussed. Solar radiation transmitted through the windows, internal heat from occupants, lamps and electric appliances inside the building and heat recovered from the ventilation system then have to be sufficient for the heating of the building. This study is of general interest since the property company, Akademiska Hus, plans to use this study as a first step in determining if this technique could be used in the future and thus be worth further investments. A building without a conventional heating system of the size investigated in this project has not yet been built.The energy needed for the heating of the building was simulated using VIP+.The conclusions from the study are that it is possible to build large buildings without any conventional heating system. This could be achieved in many different ways, for example by lowering the inside temperature or by using better windows and heat recovery system with higher efficiency.

Communication is an important part of any multi-agent system. There are different ways of communicating and they have different effects on a multi-agent system. This project describes and evaluates two different ways of communication, implicit and explicit. To compare the two methods, two experiments have been executed. The result of the experiments have been compared and discussed.

Lower energy use in buildings is a result of increasingly stringent energy requirements across Europe. When conventional district heating technology is used in areas with low energy consumption heatlosses do not fall even though the amount of energy delivered is reduced. This reduces income for thedistrict heating company. To maintain their economic viability the district heating companies? majorchallenge is to implement new solutions that minimize heat loss.

In the world we live in today the environmental issues has become increasingly important, and we have begun to realize that we can not continue to use fossil fuels at the rate we do. When it comes to generating electricity we are constantly trying to come up with cleaner and more efficient solutions. The fuel celltechnology is one such alternative and has been around for over 100 years. Yet, it is not until now that the world has started to notice this great technology. The fuel cell has been developed in several areas and can today be used for handheld electronics, vehicles and small settlements.

Photovoltaic Systems in Sweden has longbeen heavily dependent on subsidies and grants to bring in a profit for the investor. Production of excess electricity is a major reason for this as the compensation for excess electricity today is low. However, there are businesses that have an electricityneed that are particularly suitable for solar electricity. These businesses have an electricity demand when the sun shines the brightest and if the Photovoltaic System is properly scaled, the excess electricity can be minimized. A golf club is that kind of a business and this thesis aims to examinate the solar power potential for golf businesses in Sweden.Nine golf clubs was selected from different locations in Sweden.

The division of Electricity at Uppsala University is developing a wave energy converter(WEC) consisting of a linear generator connected to a bouy at the water surfacethrough a wire cable called the connection line.During extreme conditions, the wave power plant will experience forces up to 500kN, which lead to unnecessary wear and will ultimately cause the failure of theconverter. To prevent this there is a need for a damper.The wave energy converter works at a maximum efficiency when the translator?sare centered with respect to the stator. Due to tidal movements the position of thetranslator can deviate. There for a mechanical divice that will compensate for this isneeded.This report describes the further development of an earlier project where a tidalwave compensator for a wave energy converter of Seabased AB was developed.

This report aims to examine the design of a passive house. The design addresses the selection ofmaterial, sizing and selection of both building services systems and building technical features suchas load-bearing framework and moisture control. Interior layout is designed for a family of twoadults and one child.A big part of the report is devoted to an in-depth comparison of three different wall constructions ofpassive house standard. The structures that have been compared are a lightweight timber structure, aheavier concrete structure and a sandwich wall of the brand Weber Leca. The report covers variousaspects such as air flow, wall thickness, the risks associated with the construction, U-value, thermalbridges, power consumption, price, and assembly costs.

A passive house in Norra Djurgårdsstaden drawn by Tengbom Arkitekter is going to be built. A shaft for airing is needed for a few apartments in the house.The airing shaft is designed for a few two room apartments in the house, which are not able to achieve satisfactory airing, as their outer walls are facing a single direction. The other apartments on the same floor are corner apartments. These apartments do not have the same difficulty with airing since they have their outer walls in different directions, with different pressures at the facades. The airflow in the airing shaft is supposed to be driven only by natural forces, by the sun. The purpose of natural driven forces is to achieve low energy consumption for the house.In this thesis, a design of the shaft for airing has been developed.Initially an open shaft for all apartments was analyzed.

This report aims to examine the design of a passive house. The design addresses the selection ofmaterial, sizing and selection of both building services systems and building technical features suchas load-bearing framework and moisture control. Interior layout is designed for a family of twoadults and one child.A big part of the report is devoted to an in-depth comparison of three different wall constructions ofpassive house standard. The structures that have been compared are a lightweight timber structure, aheavier concrete structure and a sandwich wall of the brand Weber Leca. The report covers variousaspects such as air flow, wall thickness, the risks associated with the construction, U-value, thermalbridges, power consumption, price, and assembly costs.

This report aims to examine the design of a passive house. The design addresses the selection ofmaterial, sizing and selection of both building services systems and building technical features suchas load-bearing framework and moisture control. Interior layout is designed for a family of twoadults and one child.A big part of the report is devoted to an in-depth comparison of three different wall constructions ofpassive house standard. The structures that have been compared are a lightweight timber structure, aheavier concrete structure and a sandwich wall of the brand Weber Leca. The report covers variousaspects such as air flow, wall thickness, the risks associated with the construction, U-value, thermalbridges, power consumption, price, and assembly costs.

This report examines the possibility of developing a modular system for concrete homes that cancontribute to greater diversity of today's market. The issue was whether it ? from a competitive pointof view ? is possible to produce smart prefab modules that customers themselves can combine to avilla. The report addresses the question how the modules and wall panels should be designed for thegreatest variety of floor plans.With regard to what is asked of the customer interviews where held for the purpose ofunderstanding concrete's popularity and elements of high value in their homes today. The answersfrom the interviews laid ground for four prototype homes which were made to demonstrate how theelements can be combined to achieve different types of houses..