The objective of this work was to introduce measures to reduce energy and water demand at Gävle Söder 17:10. To succeed, this energy audit has been made. The work is based on collected statistics from the property owner Norrporten, measurements, literature review and through consultation with experts in the field. Two models, one for each building, have been created in the simulation program BV2 to estimate the potential of energy measures based on the collected information. The models in BV2 have been verified against the statistics of the energy consumption.With the help of calculations and simulations, seven cost-effective measures have been identified.

New technology makes it possible to remotely measure all consumers in a power network onan hourly basis and store the values in a database.This thesis work describes the conversion process between automatic meter reading systemMActor and calculation software Xpower.Then the possible differences between calculations of power networks using load curves incombination with a yearly estimate of consumption and calculations using hourly measuredvalues is examined.The result of the comparison shows that, for the power network under inspection, nosignificant difference could be noticed. This does not mean that calculations using hourlymeasured values would be unnecessary. I believe that in a near future calculations using hourmeasurements will be the primary choice for many power companies to whom technology isavailable.Also some basic calculations of fundamental power network parameters, such as power factorand loses, are presented using hourly measured distribution transformers in combinations withits hourly measured loads.The report is written in Swedish.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

This paper is about the extent to which simplified penetration calculations ofsmall-caliber projectiles is a useful tool for assessing the physical protectioncapability. The work should be seen as an attempt to create an accessible tool inthe form of a simplified equation that allows for a better and safer use of thenaval vessels. The tool will also be used at different levels so that decisions andinstructions could be clearer.Performed calculations show a very limited capacity of a ship's basic design interms of physical protection against the use of small-caliber projectiles.How do we know that the calculations correct? By verifying the calculations withpractical shooting tests, a substantial condition to answer the question will becreated. To shoot against a material with two different thicknesses estimated toproduce perforation and non-perforation is a good approximation of the equationusability in the context..

One of the city of Stockholm?s main objectives is to have a society completely free from fossil fuels. To achieve this, several investments regarding improvements in energy efficiency and renewable energy are currently being planned or implemented. One of these investments is a project called Hallbara Jarva which is located in the suburbs of Stockholm. The purpose of this thesis is to examine the prospects of an investment in photovoltaic cells from an energy-saving and economical point of view. The analysis is limited to three buildings within Hallbara Jarva and is intended for the property owner.  Solar energy is a type of renewable energy source and is commonly divided into solar heating and solar power.

This is a work that look at the factors that affect future monthly costs when buying a house in Sweden and which options are the most financially favorable over a 30 year period. The work also examines whether it is economically beneficial to invest in a low-energy house regardless of geographic location in Sweden, and discuss about whether a calculation template can help individuals to choose more environmentally friendly options. The work has been limited so that a certain number of predetermined factors and its measurable values have been developed with the help of a literature study. The factors chosen are building type, climate, heating systems, loan interest rates, energy prices, energy price increases, inflation rates and down payment. These are then combined into 72 different calculation cases which get put in a calculation model made in excel.

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

How to use automatically read data to create a method that visually describes how energy is used in a building, the so called energy signature..

The objective of this work was to evaluate and implement a number of energy saving functions for a specific embedded system. The functions were then grouped into a number of energy levels with known properties in terms of functionality, energy consumption, and transition time between the levels.The embedded system consisted of an AT91 ARM9 processor, GSM/GPRS modem, display, Ethernet and other peripheral units. Some energy saving methods that were considered were suspend to RAM, suspend to disk, frequency scaling, and methods for saving energy in the modem, Ethernet, USB and display backlight. The functions were grouped into levels and an interface was specified for controlling the energy level.It proved possible to get known properties within the defined energy levels, even though the paritioning of functions into these levels proved to be sub-optimal in a typical application usage scenario because it was designed for mainly energy consumption, not usage.The final result is a number of energy saving functions grouped into levels, which are controllable via an application interface. Each of the levels have a known energy consumption in both loaded and un-loaded mode..

This paper is about the extent to which simplified penetration calculations ofsmall-caliber projectiles is a useful tool for assessing the physical protectioncapability. The work should be seen as an attempt to create an accessible tool inthe form of a simplified equation that allows for a better and safer use of thenaval vessels. The tool will also be used at different levels so that decisions andinstructions could be clearer.Performed calculations show a very limited capacity of a ship's basic design interms of physical protection against the use of small-caliber projectiles.How do we know that the calculations correct? By verifying the calculations withpractical shooting tests, a substantial condition to answer the question will becreated. To shoot against a material with two different thicknesses estimated toproduce perforation and non-perforation is a good approximation of the equationusability in the context..

The energy consumption in the sectors of residential and public buildings is 40 % of the total energy consumption in Sweden. The main part, 85 %, of the energy use in these sectors is for operation of the buildings. The rest is used in the building process. When energy-efficiency measures are taken the energy use during the operation time decreases and the fraction of energy consumption during the building time increases. This project is carried out in cooperation with JM AB and concerns the energy use during the building time of production of blocks of flats at the building site.The main part of the electricity that is used during the production of apartment buildings goes into the heating of portacabins and illumination of the building during the construction phase.

The Energy Performance Certification in Sweden was developed as a tool to achieve the Government's target to reduce Sweden's energy consumption by 20 percent by 2020. The Energy Performance Certificate has previously received some criticism for not fulfilling its purpose. Questions that formed the basis for this report is how the energy performance certification provides support to buyers of single-family houses and if the energy performance improved in terms of reliability. The report begins with a background description that describes how the energy declaration works and some of the findings of previous evaluations and surveys. A survey to investigate the broker's position to energy performance have been conducted as well as interviews with buyers and sellers of houses. An investigation whether the energy performance can vary between different calculation programs, depending on various assumptions made by the energy declarant, has been made.Brokers and sellers have proved negative attitudes towards energy performance, particularly brokers.

Rising energy prices and higher energy demands have led to an increased focus on energy efficiency, in particular in the real estate business, where high potential for energy savings exists. Within the next few years, buildings that were constructed in the sixties and seventies will be in need of renovation. One of the challenges of these renovations will be to improve energy efficiency. A real estate company that is facing this challenge is Uppsalahem AB, based in the city of Uppsala, Sweden. This study focused on analyzing energy efficiency measures when renovating old buildings.

AbstractThe Energy Declaration is a law that will come into effect October 1: Th 2006. This report has Värnamo municipality as principal and shall clarify what the estate owner in general and Värnamo municipality in particular need to know about this law. Another part that is going to be dealt with is how large the future need for energy experts in this field will be, and which competence that will be demanded for them.The work will in general deal with simplified energy declarations for apartment houses and public buildings, since these buildings are the first to be involved with energy declarations.The energy declaration will consist of a number of important components.? Energy power i.e. how much energy the building consume? If the ventilation control is done? If the radon measurement is carried out? Recommendations of measures to improve the energy power? Reference value to compare the buildings energy power againstAccording to the law the declaration shall been made by an independent expert, which will need certain information for this.

This paper is about the extent to which simplified penetration calculations ofsmall-caliber projectiles is a useful tool for assessing the physical protectioncapability. The work should be seen as an attempt to create an accessible tool inthe form of a simplified equation that allows for a better and safer use of thenaval vessels. The tool will also be used at different levels so that decisions andinstructions could be clearer.Performed calculations show a very limited capacity of a ship's basic design interms of physical protection against the use of small-caliber projectiles.How do we know that the calculations correct? By verifying the calculations withpractical shooting tests, a substantial condition to answer the question will becreated. To shoot against a material with two different thicknesses estimated toproduce perforation and non-perforation is a good approximation of the equationusability in the context..