In this work an assessment of the compressed air system in the facilities of Vattenfall Heat Uppsala has been conducted. The facilities constitutes, among others, a combined heat and power plant, and two waste incineration plants. The compressed air is supplied primarily by seven rotary screw compressors and yearly electric energy consumption in these has been determined. Furthermore, the usage of compressed air has been mapped in order to find processes with energy savings potential. Several suggestions how to reduce the usage of compressed air have been presented, resulting in decreased need of electric energy and reduced CO2-emissions.The results show that total need of electric energy in the compressors, during a standard production year, amounts to 5.83 GWh.

Human existence and welfare depend on functional ecosystems. Ecosystems are critical to sustain life-support services for human well-being. One method that visualizes that humanity requires ecosystem services for resource consumption and assimilation of produced waste is ecological footprints. This study focuses on the ecosystem service carbon sequestering. A quantification of this ecosystem service showed the potential for accumulation of carbon in different ecosystems in Stockholm and Norrbotten County for the years of 1995 and 2004.

The requirements for wastewater treatment plants (WWTP) are gradually increasing, partly because of higher incoming loads, which in turn require a more efficient treatment process. In parallel with environmental and economic goals there are also desires to lower energy consumption without compromising the wastewater treatment. Furthermore, there is a demand on WWTP´s to alter eutrophication in aquatic systems through better nitrogen and phosphorus removal. An increasing number of WWTP´s have acquired biological nitrogen and phos-phorus removal. A by-product of this type of biological treatment is the formation of nitrous oxide, which is a potent greenhouse gas.

The environment has become an important part in people´s lives, and in today´s society stakeholders demands have increased upon companies when it comes to sustainability reports. How these sustainability reports are designed depends on whom it?s for, laws and regulations, and the companies own norms and values. The purpose of sustainability reports is to measure, monitor and compare a company´s enviromental impact. It?s not only about integrating economics, but also enviromental and social standards together to get both financial and competitive advantages.Sustainable Value method is a new model and is the first real method that can be used to evaluate a company´s resources, both financial, social and enviromental to a sustainable value.This model is used to compare the resource efficiency between companies.In this thesis, a documentary study with an experimental approach has been made.Sustainability reports from six selected companies (in the engineering and forestry sector) have been investigated with respect to their accounting for carbon dioxide, and an experiment using the method ?Sustainable Value Approach? was subsequently performed.

Australia is one of the largest producers and consumers of fossil fuels in the world. In a society where the effects of fossil fuels on global warming are constantly discussed, the nation?s production and consumption are subject to debate. Problems arise when negative aspects of consumption, such as emissions of greenhouse gases, are put in relation to an increased need of energy and economic growth. However, it is important to distinguish between different types of fossil fuels when it comes to their individual impact on the environment and to analyze the possibilities to increase the more environmental friendly ones.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area.

Deposited waste material degrades within a short period in anaerobic environments. The methane gas that is formed provides a harmful contribute to the greenhouse effect, 23 times larger impact than carbon dioxide. It is therefore desirable to minimize the emissions of methane gas from landfills. This may be achieved by drain the landfill of gas. In this thesis the amount of produced methane gas at the landfill at Örebro has been calculated. Estimations have also been made of the amount of methane gas that might be produced in the landfill in the future.

Lokala investeringsprogram was a subsidy program which supported environmental reforms during the years 1998 to 2002. The subsidies were given to Swedish municipalities. Most of the evaluations of the subsidised projects have now been completed and included in a database. The purpose with this thesis is to analyse whether the instrument has been effective with respect to carbon dioxide reductions and costs. These calculations have focused on subsidy and cost efficiency. The analysis has been compared with a previous report called "LIP ur ett samhällsekonomiskt perspektiv". The result shows that the reduction cost for one kg CO2 has been almost one SEK, which is twice as high as the cost reported in a previous report, half a SEK.

The number of data centers and their capacity is increasing throughout the world. Theenergy used in these data centers and the emissions from the use are increasing at thesame rate. The total use of energy will double from 2008 to 2011 based on the trends indata centers use. Research in this area says that the emissions from data centers willhave surpassed the level of airline traffic in 2020. The index used today to compare howefficient a data center is, called PUE, is lacking some information.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area.

The aim of my thesis was to do a Life Cycle Assessment (LCA) of an average thread tap that is manufactured by Dormer Tools AB, and to create a practical model that the company can use in order to study other thread taps from an environmental perspective.The method of LCA is used to investigate the environmental effects of a product during its life cycle. This is a gate-to-grave analysis with focus on steel and thread tap manufacturing, coating procedure, use, waste management and transports. Three common coating types were compared separately. Steel manufacturing answers for the highest energy and raw material consumption under the life cycle of the thread tap. Its emissions contribute to global warming, acidification and eutrophication above others.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area. The results show that use of locally installed renewable energy sources can reduce the total climate impact when life cycle perspective is applied.

The energy use in a workshop company has been examined in this work in order to find areas for energy efficiency improvement. The combined oil and electricity heating in the company were compared with other alternative heating systems including cooling of the premises in following combinations:Ground source heat pump for heating and coolingDistrict heating and absorption coolingDistrict heating and low temperate surface water coolingEnergy use, operation costs and carbon dioxide emissions were calculated for the current heating systems and the three alternatives including cooling. The ground source heat pump for heating and cooling decreases bought energy with 34 MWh annually compared to current heating only. The district heating and low temperate surface water cooling has the largest reduction of operation cost and carbon dioxide. The operation cost decreases with 42 kSEK and the carbon dioxide with 43 metric ton CO2 annually.

With the climate change issues growing in importance on the social agenda, the field of urban masterplanning is of no exception when it comes to minimizing the carbon footprint in a variety of projects. The aim of this thesis has been to prepare the Carbon Critical Masterplanning tool, a software plugin for carbon dioxide emissions assessment developed by Atkins, to be used in Swedish conditions. The main targets were to improve the areas of the tool associated with energy conversion and renewable energy sources, and to test the tool in a real case. A planned construction of a new campus in Albano, Stockholm was chosen for the pilot study. A 3D model was built in the tool and the carbon footprint was calculated for a variety of combinations for energy supply to the future area.

Background and problem: In the last few years the threat against the environment and especially the emissions of carbon dioxide has become increasingly debated. The government have set up a goal to lower the emissions of carbon dioxide with 40 percent until 2020 compared to the level in 1990. The emissions in the transportation sector have, in contrast to the total emissions, increased since 1990 and will continue to increase unless powerful control measures are implemented. The lorry centres have to use strategies to answer to these external threats which lead us to the two questions of this thesis: - What methods do the lorry centres use actively and which do they consider as the most important methods for fuel saving? - Are there any differences which methods small, medium and large centres considers as important? Purpose: The main purpose of this thesis is to examine which methods lorry centres use actively and which they consider as important for fuel saving.