Warnit AB har under ett tidigare examensarbete vid LTU utvecklat ett intelligent larmsystem som känner av vibrationer och automatiskt sänder ett trådlöst larm till användaren via SMS eller e-post. För att utveckla ytterligare produkten har Warnits VD, Peter Stenlund kommit med ett förslag om effektmätning på trefassystem. Detta examensarbete har i samarbete med EISLAB (Embedded Internet System Laboratory) vid Luleå tekniska universitet resulterat i ett prototypeffektmätningssystem för aktiv, reaktiv och skenbar-effekt på symmetriska trefaslaster. Aktiv, reaktiv och skenbareffekt kan avläsas både på plats via en display och via Internet på en webbsida genom att använda WarnitBoxens trådlösa kommunikationsmöjlighet för att koppla den trådlöst till Internet..

This master thesis is an analysis of how the amount of health centers per inhabitant has changed since the Swedish government implemented a new health care reform in 2010. The reform implies a free choice of health centers in the Swedish regions and opens up the market for private firms. The purpose of the thesis is to study the effects of the different financing systems toward the health centers in the regions. The models are based on theories of the need of health care. Two of the independent variables which are studied are income and age.

Eutrophication of the Baltic Sea and Swedish lakes remains a major problem despite many years of effort to reduce the emissions of nutrients. One major source is waste water systems, especially private sewage systems. These sewages accounts for a very large share of nutrients per capita in comparison with citizens connected to larger sewage treatment plants. Norrtälje community has the greatest number of private sewage systems in Sweden. Discharges of nutrients, especially phosphorus, to the Baltic Sea from these sewage systems are significant.

Drain water heat recovery is an uncommon measure in multi-unit residential buildings. There istechnology available for the purpose but the knowing and experience of the heat recovery systems islittle. The purpose of this thesis is to evaluate the future potential of drain water heat recovery inmulti-unit residential buildings.A major part of the multi-unit residential buildings in Sweden were built during modernismen andrekordåren (1940?1975). Many of the buildings have worn out drain and water supply systems andmany are in need of a general refurbishment.

Wastewater treatment is increasingly controlled by the Swedish environmental quality objectives, adopted by the Swedish parliament. There is a need for a sewage system that can fulfill stringent requirements concerning the environment, recycling and resource use and hygiene. Additional environmental aspects in recent years are the impact of climate change, new knowledge about the effects of pharmaceuticals in water, the need for improved wastewater treatment and increased recycling of nutrients to agriculture. This report has, from a future scenario of the year 2050, analyzed seven different systems for wastewater treatment and treatment of compostable biowaste from households in Eskilstuna. A future scenario was chosen based on that within a forty year period new challenges may arise which can result in higher demands on sewage treatment than those we see today. Another reason why the future scenario was established is that changes in wastewater treatment systems are slow to establish. The analysis is mainly focused on the economical aspects but environmental aspects such as emissions to receiving waters and potential recycling of plant nutrients has also been evaluated briefly.

This thesis aims to investigate SAAB AB´s possibilities to use synthetic instruments in their test systems. The reason for this is reducing costs and the risk of obsolescence which is common when test systems operate for several decades.The market around synthetic instruments has been explored in the search for suitable hardware and software. Software has been developed in LabVIEW and synthetic instruments have been created with the help of IVI-drivers. The hardware consisted of PXI-instruments (Waveform generator and Digitizer), connected to a computer using a fiber optic link and PXI-chassi. The created instruments was then compared to common instruments used today, and the comparison turned out well.

ERP system is the information technology that has had the biggest impact in companies? development and way of working in today?s world. ERP system is divided in several applications with a modular software design that allow people in every department in a company to store and retrieve information accurately and in real-time. This master thesis investigates attitudes toward ERP systems among business organisations and ERP suppliers with the overall purpose of analysing to which extent a new ERP system will bring change in the business process. The purpose of this thesis is to make a survey of attitudes toward ERP systems among business organisations and ERP suppliers.

As an amateur it can be difficult filming from several angles at the same time as this requires several cameras. It´s also hard to film at occasions when it´s not appropriate to manoeuvre the camera manually. Systems for solving these problems already exist, but it´s either more expensive, professionalsystems or cheaper systems with limited functionality.The purpose of this project is to develop a cost efficient solution to the problem above that offers a better functionality then existing commercial systems. The biggest difference from existing products is the wireless video feedback from the camera to the remote unit.The result of the project is a system consisting of two units, a manoeuvre unit with a cradle for the video camera and a remote unit from which the operator can control pan and tilt of the video camera.Communication between the two units is wireless.On the remote unit there is a joystick and a display mounted. In addition to this, there is also an IR receiver that is capable of reading the signal from the cameras own remote and sending it to the manoeuvre unit.The manoeuvre unit is equipped with one motor to control the tilt function and one motor to control the pan.

Problem: Our opinion is that it is important to consider about usability in system development. In this thesis we will focus on usability in point-of-sale systems. The point-of-sale system we base this thesis on is Extenda Retail. Our case study is performed on Ica Kvantum in Bromölla, which implemented Extenda Retail about two years ago. Purpose: The purpose of this thesis is to figure out what important factors there are to consider, in usability aspects, when developing point-of-sale systems, with focus on the cashier.

Scania Top Team is a competition where the best mechanics in the world are competing against each other. In 2011, the world final was recorded and this material is now used to see which problem solving strategies these top of the line teams are using to solve the realistic problems assembled in front of them. To help them, the mechanics are allowed to use two of Scanias IT-systems: Scania Multi and Scania Diagnose and Programmer 3. This report consists of two parts. The first part is the development of a method to analyze the recorded material.

Malt lymphoma is a malignant disease that can arise in a variety of extra nodal sites. Previous studies indicate that tumour arise from more mature B-cells.Our purpose was to examine the presence of clonality and somatic hypermutation of immunoglobulin (IgV?) of MALT lymphomas.Paraffin-embedded tumour samples from13 MALT lymphoma were subjected to rearrangement analysis, by using PCR, heteroduplex gels and sequence analysis.Successful amplification was seen in 10/13 cases and sequences of IgV? genes were obtained in 6/13, all of them were mutated. The percentage of mutation compared to germline sequences was 1,1% to 8,6% monoclonal rearrangemang. It was demonstrated that 5 of 7 clones were derived from the V?3 family, 2 from V?1 and 1 from the V? 4 family..

Today, we can see that social navigation is embedded in different kinds of websites, but there is still little support for social navigation in the web browser. Our main concern has been how we construct a tool that fills this hole in the web browser. By letting the theory, the prototype and the focus group serve as input/output to each other we could create a better overview of how the different pieces were intertwined. This has been a crucial mental model for us to obtain since it has helped us to understand how we could realize the theory through our prototype and thereby come to the conclusion of what aspects of the theory that we should put forward to further development. After constructing the prototype we thought that it would support social navigation, but realized after analyzing the discussion of the focus group that we are not there yet.

This thesis studies the concept of balance in the management control systems (MCS) of a small Swedish company within the IT-sector. The aim is to evaluate the importance of balance and dynamics in MCS and investigate which factors affect them. The frameworks used are Simons (1994) four levers of control, and the five-factor model for balance and dynamics by Mundy (2010). The small IT company - the object of the case study - has grown extensively in the last years and needs to develop more formal MCS without losing efficiency and creativity in their fast-moving industry. The case study reveals that balancing MCS is important also in smaller companies with less formal MCS.

The mainpart of this thesis is about the developing of a new analysis tool to be used in Zenicor Medical Systems AB ECG-system. The primary task of the system is to simplify the ECG survey for patients who suffers from different kinds of arrythmias, for example heart fibrillation. With this system is it possible for the patients to do their ECG survey by them self at home and then send the signal with their telephone or mobilphone to a server. The equipment used to do the survey is not bigger than you can have it in a pocket and this results in a bigger flexibility for the patient. A doctor can connect to the server and analys the ECG-curve and follow up the patients condition..

The existence for companies today consists of constant challenges with customers that want more individual products with high quality as quickly as possible. For a company to be able to have a short delivery time, it must also have a short production time. This makes streamlining and improvement of processes a big part of a company?s workThis thesis has been carried out together with the company Lasermax Roll Systems AB, a world-leading manufacturer of feeding, finishing and monitoring systems for high-speed digital printers. They manufacture their products according to the assembling for costumer order principle.The purpose with this thesis is to map and analyze, the assembling process and the test process at Lasermax Roll Systems AB.