Wavecraft AB develops medical equipment for heating of organic synthesises. The heating is done with microwaves, which improves the process in both speed and accuracy compared to the more traditional methods where heating elements are used. This report discusses the developement of an automatic lid mechanism for one of Wavecraft's product prototypes. The company assumes that the final product will be integrated by customers into fully automated systems, and the upgrade from a manually to an automatically controlled lid is therefore an important step in the product's developement process.The first stage och the project was an idea generation process. The ideas generated here were organized into five different concepts of which the best one was selected through the use of a concept matrix.

The development in electronics increases the demand for good design methods and design tools in the field of electrical engeneering. To improve their design methods Ericsson Microwave Systems AB is interested in using computer tools to create a link between the specification and the implementation of a digital system in a FPGA. Xilinx System Generator for DSP is a tool for implementing a model of a digital signalprocessing algorithm in a Xilinx FPGA. To evaluate Xilinx System Generator two testcases has been designed. The testcases are selected to represent the FPGA designs made at Ericsson Microwave Systems.

The purpose of this master thesis is to construct a steering transmission, for a trackedvehicle, containing two hydraulic circuits which are connected. The steeringtransmission should be mechanical to avoid steer-by-wire.BAE Systems Hägglunds has in an earlier study examined a system with two hydraulicpumps and one hydraulic motor, but the safety of the system wasn?t sufficient.To achieve sufficient redundancy there must be two hydraulic motors, which arecontrolled separately. When the two systems are connected in one point, this point is acritical part of the system because it directly affects both circuits. If one of the hydrauliccircuits fails the other should be able to operate independently as a steeringtransmission.

These studies are done in behalf of Saab AB AVITRONICS in Järfälla in the form of a thesis atthe Royal Institute of Technology in Stockholm.The task was to examine the parameters that plays a role in the construction of modern radomesoperating in broadband applications.This was interesting for Saab to get an indication of which way they should go at the newdevelopment of radomes for the next generation of equipment for electronic warfare.After a thorough analysis of the influencing parameters, a optimization application was made toget a automated way to get a radome design by specifying data on the radome size, airloads,materials, etc.This is to minimise the time of the laborious work that radome development.inply.This was solved by letting ANSYS calculate the strength of the radome structure and MATLABcalculate electromagnetic data and cost models of different sizes and materials.All these parameters woven together with the optimization tool modeFrontier picks data from therespective program and perform an optimization algorithm and then iterate a step and sends thisdata to calculation programs for the new input data. In the end, we have received a convergedpoint with our optimal solution.For the presumptions and limitations for which applied for this thesis, the result was prettyintuitive. That is to say that the smaller radome - the less materal is needed and lowermanufacturing costs results in the cheapest solution possible. The reality is not so simple. Whereyou have to take more of the electrical details such as the effect on the transmitter as a majorfactor..

The electric car has existed for over a century and producers has tried to commercialize it earlier but has not succeeded. In recent years, however, a change occurred that may be significant for the electric car and it is now to commercialize in the market of passenger cars. The technology has in recent years elaborated as more car manufacturers have started to invest in development in the subject field. This thesis aims to compile an action plan for the development of charging infrastructure for electric vehicles in Uppsalahem ABs residential areas. It is based on a survey of different residential areas and a survey of charging infrastructure.

This paper examines the power producing dams along the Ume-river as an integral part of and a result from the urbanization process in Sweden during industrial capitalism. The aim of the paper is to contribute to the knowledge of the urbanization process in Sweden in general and of its traces along the Ume river in the county of Västerbotten in particular. The paper applies the theory of concentrated urbanization and extended urbanization put forward by Neil Brenner and Christian Schmid (2015) and argues that the building of power producing dams along the Ume-river is part of an extended urbanization process. This becomes particularly evident when examining the vast physical structures that is the dams, situated in an otherwise remote and sparsely populated area. These vast physical structures are also very well connected to a nation wide electric grid that has connections to bordering countries as well.

The main project Dry preservation of source-separated organic household wastes involves a new technique for treatment of biowaste through drying. Investigations are going on to determine how the dried biowaste best can be used to close the natural circular flow of nutrients. The objective of this degree project is to determine if the dried biowaste can be used as a soil conditioner. By restoring the nutrients in the material to the ground, the natural circular flow is closed. A declaration of contents, including the nutrient levels, C/N ratio, pH and the electrical conductivity of the dried biowaste, was constructed and a germination test was done to make sure that the material did not inhibit sprouting.

The combustion engines in today?s vehicles are getting more and more advanced and there are increasing demands on that the engines should operate during optimal conditions. Examples of internal combustion engine parameters which may be carefully controlled are the rate between fuel and air, that this gas mixture is homogenous enough and that it is ignited at the correct moment. Moreover, the requirements of these parameters vary depending on, among other, engine speed and load. To meet these requirements in all occurring operation conditions, it is required that many subsystems work together.

Today?s environmental discussions have led to more progress in the different transportareas. To ride a bicycle is often one of the most efficient alternative when it comes totransport. An Electric bike is, and makes transportation more efficient than a regularbicycle. Electric bicycles do not affect the environment significantly and allows moreconvenient transportation than ordinary bicycles do.

Results have shown that flow batteries may be a solution in the future as an effective and environmental friendly method to an energy storage system (ESS). The technology is reliable and has a high efficiency that comes with low energy losses and a long lifetime. The range of possible fields is suitable for cutting energy peaks in the power grid, by always have a ready and available energy storage that balances the production. By comparing the advantages of flow batteries with conventional batteries it is mainly the fact that they can conserve energy for a long time without being self-discharged thanks to that the storage capacity is in principle endless and limited by the size of the electrolytes tanks that makes them a great energy storage system. The batteries won?t take any damage or decrease in performance when charging or discharging it or if you exhausts it to 100 % and leave it discharged for a long time.

The thesis evaluates a new kind of bearing arrangement in a traction motor that ABB hasdeveloped. Since the arrangement is designed in a new and innovative way it needs to beevaluated to see if it is safe to use. In today?s traction motors, bearings with a big internalclearance (C4-clearance) are used. The basic idea of the new arrangement is to reduce the fitsbetween the bearing and shaft/house.

Hallin, Dan (2009) Elevens val. En studie av elevers intresse och motiv för valet av gymnasiets Elprogram. (The pupil?s choice. A study of students? interest and motivation for the selection of the electrical program at the upper secondary school). Skolutveckling och ledarskap, 90 hp.

Wavecraft AB develops medical equipment for heating of organic synthesises. The heating is done with microwaves, which improves the process in both speed and accuracy compared to the more traditional methods where heating elements are used. This report discusses the developement of an automatic lid mechanism for one of Wavecraft's product prototypes. The company assumes that the final product will be integrated by customers into fully automated systems, and the upgrade from a manually to an automatically controlled lid is therefore an important step in the product's developement process.The first stage och the project was an idea generation process. The ideas generated here were organized into five different concepts of which the best one was selected through the use of a concept matrix.

This thesis describes redesign and adaption of a products housing. In order to make it more economical to produce at a lower production volume. The thesis is based upon a prototype that a previous student developed for injection moulding. The goal is to find alternative manufacturing methods, but also to identify parameters that affect the cost of the injection moulding tool.The housing must be tough in order to protect the circuit board inside. But at the same time it must allow sound, light an electrical communication to pass through.

Many of todays studies show that district heating is one of the betteralternatives as heating source because of its low environmental load.The energy source is often leftovers from other processes producing energy or waste, like garbage or chips.Electricity in combination with geothermal heating is another heating system that has increased sharply during the last years, and also this system decreases the discharges that have negative affectson the environment compared to several other heating methods.This report aims to, concentrated towards these two different heating systems, estimate the amounts of discharges they indirect cause and how the environment is affected.We have calculated the mean value for discharges of carbon dioxide, nitrogen oxide, sulphur oxide and dust generated from electrical power used in Sweden.Through interviews and research we have gained data for the same substances that district heating based on combustion of garbage and biofuel generates.We have also in cooperation with a housing company chosen a building we see representative for many of the new single-family houses built in Sweden today.Based on its shape and appearance we theoretically created three alternatives of the same house, each of them with climate screens different from each other.Together with the amounts of discharged environmental affecting substances, these houses were the base for our calculations and studies when investigating the different heating sources environmental effect.The results have thereafter been analyzed and discussed from different angles..