Detta examensarbete ger en introduktion till området systemutveckling. Kravhantering har i alla tider varit en viktig del i systemutveckling. För att kunna lyckas med kravhanteringen under ett systemutvecklingsprojekt är det viktigt att använda sig av rätt teknik. En teknik som finns för att kunna hantera de krav som ställs på ett system är Use Case som härstammar från UML. Syftet med detta examensarbete var att ta reda på de för och nackdelar som har upplevts av användare som har arbetat med Use Case i samband med kravhantering.

Detta examensarbete är utfört på uppdrag från AVL Södertälje Powertrain Engineering AB.Målet med arbetet har varit att utveckla ett styrsystem för ett elektroniskt styrt pneumatiskhydraulisktventilsystem på en encylindrig förbränningsmotor i en testcell. AVL är enoberoende firma som utvecklar drivlinor med förbränningsmotorer samt instrumenterings- ochtestsystem. Ventilsystemet, med ett fungerande styrsystem, ska användas i AVLs utvecklingsochforskningsarbete på förbränningsmotorer.Ventilsystemet,Free Valve Technology, är utvecklat av Cargine Engineering AB och består avelektroniskt styrda pneumatisk-hydrauliska aktivatorer som opererar en motorventil individuellt.Aktivatorernas styrsystem har utvecklats helt iSimulink och implementerats som en integreraddel i det av AVL utvecklade motorstyrsystemet Raptor. Hårdvaran och plattformen är ett rapidprototyping system från dSPACE GmbH. Systemet har visat sig fungera tillfredsställande i entestcellmiljö vid lyfthöjder större än 3 mm och varvtal lägre än 2500 rpm, även underförbränning.

The combustion engines in today?s vehicles are getting more and more advanced and there are increasing demands on that the engines should operate during optimal conditions. Examples of internal combustion engine parameters which may be carefully controlled are the rate between fuel and air, that this gas mixture is homogenous enough and that it is ignited at the correct moment. Moreover, the requirements of these parameters vary depending on, among other, engine speed and load. To meet these requirements in all occurring operation conditions, it is required that many subsystems work together.

Ibland kan det förkomma problem mellan utvecklare och kund/användare då de tar fram kraven till ett nytt system. En anledning till detta kan vara att utvecklingsgruppen och användargruppen inte har samma kunskaper och erfarenheter och talar då inte "samma språk". En lösning till detta problem kan vara att ta hjälp av en mockup. En mockup är en fysisk och/eller interaktiv modell av ett gränssnitt. I detta arbete har vi, med hjälp av intervjuer och observationer, undersökt om detta hjälpmedel underlättar kommunikationen i verkligheten..

During Spring semester 2011, Linda Engstrom and Malin Heder performed ?Golden Ratio?, a thesis which included 22.5 hp. The thesis followed the syllabus for the Degree Project for degree of Bachelor of Science in Innovation and Design Engineering (MSGC12) which was a unit in the Innovation and Design Engineering program within the Faculty of Technology and Science at Karlstad University.The client was Crem International AB, a company located in Åmotfors that develops the design, manufactures and markets coffee machines. The supervisor at the company has been Peter Larsson and supervisor at Karlstad University has been Monica Jakobsson. Examiner for the thesis has been Professor Fredrik Thuvander at the Faculty of Technology and Science at Karlstad University.Crem International AB controls a patent, representing a new technology to streamline and minimize use of energy during the coffee preparation and results in a good coffee quality.

The pdf is excluding images, because of uncertainties regarding copyrights. Instead I have put links for each picture so you may find them on the Internet. For a list of links to the online sourcematerial, please visit http://del.icio.us/Cyborguppsats.

This Master of Science thesis was completed at the Department of Machine Design at the Royal Instituteof Technology in Stockholm in collaboration with Lund Faculty of Engineering, Luleå University ofTechnology and Stanford University. At Stanford University a global product development project wasrealized as part of the course ME310. The project was initiated by the American company ImmerseGlobal whose vision was to develop a new type of Atmospheric Water Generators, a machine that absorbsthe moisture in the air and via a water system transforms it to pure drinking water. The project was partlyfinanced by the Product Innovation Engineering program, a Swedish research and development programfor increased innovation capability in organizations.In parallel with the global project in the ME310 course the product development process was studied inorder to compare it with a product development course at the Royal Institute of Technology, IPU. Thetwo courses are similar to each other in several aspects.

Results have shown that flow batteries may be a solution in the future as an effective and environmental friendly method to an energy storage system (ESS). The technology is reliable and has a high efficiency that comes with low energy losses and a long lifetime. The range of possible fields is suitable for cutting energy peaks in the power grid, by always have a ready and available energy storage that balances the production. By comparing the advantages of flow batteries with conventional batteries it is mainly the fact that they can conserve energy for a long time without being self-discharged thanks to that the storage capacity is in principle endless and limited by the size of the electrolytes tanks that makes them a great energy storage system. The batteries won?t take any damage or decrease in performance when charging or discharging it or if you exhausts it to 100 % and leave it discharged for a long time.

During Spring semester 2011, Linda Engstrom and Malin Heder performed ?Golden Ratio?, a thesis which included 22.5 hp. The thesis followed the syllabus for the Degree Project for degree of Bachelor of Science in Innovation and Design Engineering (MSGC12) which was a unit in the Innovation and Design Engineering program within the Faculty of Technology and Science at Karlstad University.The client was Crem International AB, a company located in Åmotfors that develops the design, manufactures and markets coffee machines. The supervisor at the company has been Peter Larsson and supervisor at Karlstad University has been Monica Jakobsson. Examiner for the thesis has been Professor Fredrik Thuvander at the Faculty of Technology and Science at Karlstad University.Crem International AB controls a patent, representing a new technology to streamline and minimize use of energy during the coffee preparation and results in a good coffee quality.

Syftet med detta examensarbete är att vidareutveckla glasfiberbalkar så de kan användas som mellanbjälklag i småhus. Förebilden var ett ?Delta Deck? som utvecklats av Altakor Group och används i brokonstruktioner. Denna profil har vi sedan modifierat och optimerat för bruk i småhus. Den största skillnaden är att vi valt att inte använda den så kallade ?snap-fit?-tekniken.

With the huge amount of computers connected to the Internet the IP-addresses are starting to run out. The Internet Engineering Task Force, IETF, have decided that it is about time to exchange the old 32 bits Internet protocol, Ipv4, to a more modern 128 bits protocol called Ipv6. This thesis explores the possibility to install Ipv6 in different operating systems. By testing various operating systems and by set up criteria compare them to each other we give the reader a picture of how the installation is done. We also show which operating systems to prefer if you want to use IPv6.

This report describes the scientific work of designing and manufacturing an intelligent controller module prototype for automobile trailer connections. The functions of the module are both to drive the lamps and detect failures. The module also contains functions to handle other functions of the trailer. To learn about controller modules the group does extensive feasibility study.The group receives three already existing modules, the functions of the three modules are studied and tested in the lab, this is done too get a overview of the construction. The method used I called reversed engineering, a way of constructing by analyzing constructions already done.When the modules are analyzed, the functions of the prototype are tested and designed without copying the analyzed modules.

During Spring semester 2011, Linda Engstrom and Malin Heder performed ?Golden Ratio?, a thesis which included 22.5 hp. The thesis followed the syllabus for the Degree Project for degree of Bachelor of Science in Innovation and Design Engineering (MSGC12) which was a unit in the Innovation and Design Engineering program within the Faculty of Technology and Science at Karlstad University.The client was Crem International AB, a company located in Åmotfors that develops the design, manufactures and markets coffee machines. The supervisor at the company has been Peter Larsson and supervisor at Karlstad University has been Monica Jakobsson. Examiner for the thesis has been Professor Fredrik Thuvander at the Faculty of Technology and Science at Karlstad University.Crem International AB controls a patent, representing a new technology to streamline and minimize use of energy during the coffee preparation and results in a good coffee quality.

Hallin, Dan (2009) Elevens val. En studie av elevers intresse och motiv för valet av gymnasiets Elprogram. (The pupil?s choice. A study of students? interest and motivation for the selection of the electrical program at the upper secondary school). Skolutveckling och ledarskap, 90 hp.

Through this thesis, we want to discuss how the marginalization of people, several precedent political, city planning- and engineering decisions resulted in a catastrophic outcome after hurricane Katrina in New Orleans 2005. We also put forward a case study of the Make It Right Foundation, to demonstrate how the residents of the Lower Ninth Ward are involved in the urban development of their community. We would like to draw attention to the power of citizens and how they can influence the urban development of a community after a trauma. This study also focuses on the mission of The Make It Right Foundation: which is to rebuild the Lower Ninth Ward with firm concepts on sustainable development where all dimensions are accounted: ecological, social, cultural and economic. The empirical data was collected by a field study in New Orleans 2010-03-22 and semistructured interviews were made during the same days..