Modern semiconductor design methods makes it possible to design increasingly complex system-on-a-chips (SOCs). Testing such SOCs becomes highly expensive due to the rapidly increasing test data volumes with longer test times as a result. Several approaches exist to compress the test stimuli and where hardware is added for decompression. This master?s thesis presents a test data compression method based on a modified facsimile code.

Through a thorough analysis of the current situation, we have highlighted differences inworking methods for the various workshops and drew up proposals for improvements incombination with a practical work description that can be implemented in the company..

The focus of this thesis is primarily in electronic construction and describes the design process for a microcontroller circuit board from concept development to prototyping. The client develops test fixtures for automated testing of products within the electronics industry and needs a new controller circuit for the test fixtures that can handle controls and basic testing. An investigation into the needs of such a system is conducted and a prototype printed circuit board assembly is manufactured.The prototype is developed with focus on protection against electrostatic discharges and overvoltage. Among the functions that are included are voltage measurements, communication interfaces and control of input and output currents. Firmware for the prototype is developed and configured to communicate with a PC through USB interface for control and collecting of measurements..

The purpose of this thesis was to design an electrical system for use in a ballistic test at the Swedish National laboratory of forensic science (SKL). The detector unit would use four main parts: coilsystem, transmitter, reciever and indicator. The coilsystem would be based on a balanced system using three coils. One that creates a magneticfield and the other two will sense the differences when a metallobject is in the coilsystem. This report starts out by investigating possible solutions for this specific task followed by a description of the physics that the metaldetector use.

AbstractA continuous improvement of products and production is an important goal for a modern industrial company. A small engineering group located in Sweden came in touch with the authors of this report during the spring semester of 2014. The aim of this report is, as part of the group´s ambition of improvement, to analyse ways in which the quality of component casted parts can be verified. Non-destructive testing (NDT), and methods to use it for quality control, is the main focus of this report. However, fields such as material standards, component casting and quality engineering are analysed as well.

This report describes the construction of a climate-cabinet for testing of HV-cards (High Voltage) produced at VG Scienta. The main part of the report describes all the different components of the cabinet. The most important parts are a PID regulator from Eurotherm model 2408, a solid state contactor (SSC), a thermocouple, a finned resistor from DBK and different fans. The report even includes the connection between components by cable wiring, isolation, grounding, fuses and shaping of metal goods.As the cabinet also communicates with a computer, the report includes the solution of the data communication using the software iTools from Eurotherm. The communication part includes information about a converter that converts EIA422 to USB.The cabinet was produced at a company, called VG Scienta, in Uppsala during the spring 2010.

AbstractOur bachelor degree thesis was carried out in collaboration with Ivar Petterssons Järnmanufaktur AB in Smålandsstenar. We were asked to replace their wedge housing, used to fasten the wires to the power lines, with a similar structure in a plastic material. The idea for this project started with Ivar Petterssons Järnmanufaktur AB having problems with the casting quality that forced them to perform expensive tests on each of the wedge houses to ensure the quality. They are currently produced in China which is also a major drawback because it requires expensive long delivery times.The method we used is Fredy Olsson's Princip- and Primärkonstuktion (1995). We have consistently been in the project on so-called "broad front", which means that you create several sketches, ideas and changes in parallel, and then evaluates all.

Introduction: The current research shows that cannabis use is increasing, while alcohol use is decreasing in many countries. The reason for the increase is considered to be the increased availability and that adolescents attitudes towards cannabis has become more liberal. Aim: This qualitative study aimed to examine adolescents attitudes and knowledge about cannabis. Methods: Data has been collected from focus group interviews with adolescents aged 15-18 years, in a west Swedish municipality. Participants were recruited through visits to secondary and upper secondary schools.

Can the Danish "Aftalesystemet", a system with the intention to simplify the use of services within health care, be used in Sweden? This project has investigated the possibility by installing and testing the system and explored its functions to detect any eventual problems. Analyses were made of the system's graphical part and the underlying code to see in greater detail how the communication between units occurred, since no actual documentation of it existed. Discussions with the developers took place regarding how the current system works and how further development should continue. In order to test the system, a completely virtual environment was used.

Alternative splicing is a process that partly rejects the common definition of a gene ? that one gene codes for one specific protein. By variable combination of coding regions (exons) and exclusion of non-coding regions (introns), formation of several different mRNA-transcripts, and consequently several different proteins, can derive from the same gene. Alternative splicing is an important condition for the development of complex life forms, but it is also a highly sensitive process and inaccurate splicing is the cause of approximately 15 % of mutations that cause genetic diseases. This article presents four genes, BRCA1, BRCA2, ER? and ER?, and inaccurate splicing of these genes increases the risk of developing cancer, particularly breast cancer and ovarian cancer.

This essay is about testing the validity of an article written by Jonas Löwgren, called The use qualities of digital design. The study we have executed is about testing the featured qualities of digital design in the article on two search systems located in the library of Stockholm University and Södertörn University respectively to see how they are able to be applied on search systems. To acquire the information for the study, we handed out a written inquire among users of those systems. The result of this quantitative study shows us that many that five of Löwgrens qualities is likely to be present on the systems. Our conclusion is that five of these are appliable on search systems.

With the huge amount of computers connected to the Internet the IP-addresses are starting to run out. The Internet Engineering Task Force, IETF, have decided that it is about time to exchange the old 32 bits Internet protocol, Ipv4, to a more modern 128 bits protocol called Ipv6. This thesis explores the possibility to install Ipv6 in different operating systems. By testing various operating systems and by set up criteria compare them to each other we give the reader a picture of how the installation is done. We also show which operating systems to prefer if you want to use IPv6.

The issue about how Scania shall perform HVAC tests in the climatic wind tunnel CD7, which Scania is about to complete by year 2013, has resulted in four test methods for truck HVAC and also a test method structure. The test methods have been chosen to focus on sun, snow and rain simulations. These are adapted and developed according to what should be tested and to what can be tested in CD7, which has been the object. With CD7 different climates can be simulated in a controlled environment for complete truck level, from desert with high sun load to arctic cold and snow.The test methods represents a basis to start from, for designers and test engineers which make the testing more repetitive as well as time eventually can be saved. Before the test methods can be applied they must be verified as they are based on theoretical and empirical assumptions.

Introduction: Dolomite AB was in need of a dummy arm for crutch testing, to complement their existing test capabilities. Background: A large number of people need crutches on a daily basis. For them it is essential that their crutches do not fail. ISO (the International Organization for Standardization) conducts ongoing work to guarantee the durability and function of e.g. crutches.

There are two species of potato cyst nematode (PCN), the yellow, Globodera rostochiensis, and the white, Globodera pallida. Each of them can appear in different pathotypes. These are separated by testing the nematode ability to multiply on a number of potato cultivars with different resistance properties. The aim of this project was to examine the virulence of Swedish and foreign PCN populations and to compare two test methods. Biotests are today the only available tests used to study virulence.