The development of defoaming additives is steadily progressing and there are therefore always new and improved additives on the market. Some modern additives provide the desired defoaming effects by themselves, in contrasts to previous additives that needed to be used in combination with other additives. The task of this bachelors thesis was to evaluate the possibility of using these improved defoaming additives, with the aim to find alternatives that give the system better defoaming attributes while, at the same time, using less of the primary products. The tests were carried out in the coating type Teknocryl Aqua Combi 2780. The coating is a waterborne air Drying acrylat-latex/alkyd based coating that can be used for both single coat painting and primer.

The main project Dry preservation of source-separated organic household wastes involves a new technique for treatment of biowaste through Drying. Investigations are going on to determine how the dried biowaste best can be used to close the natural circular flow of nutrients. The objective of this degree project is to determine if the dried biowaste can be used as a soil conditioner. By restoring the nutrients in the material to the ground, the natural circular flow is closed. A declaration of contents, including the nutrient levels, C/N ratio, pH and the electrical conductivity of the dried biowaste, was constructed and a germination test was done to make sure that the material did not inhibit sprouting.

The amount of various phosphorus (P) fractions in the sediment and the relationship between the amount of P and sediment particle size were investigated in a constructed wetland southwest of Linköping. Furthermore, the possible correlation between clay content in the sediment and distance from the inlet was investigated. Sediment samples were collected along three transects from the inlet to the outlet, with six samples in each transect. In order to measure the soluble P, an NH4Cl extraction was done. This was also analysed for total soluble P after oxidation with peroxodisulphate.

The amount of various phosphorus (P) fractions in the sediment and the relationship between the amount of P and sediment particle size were investigated in a constructed wetland southwest of Linköping. Furthermore, the possible correlation between clay content in the sediment and distance from the inlet was investigated. Sediment samples were collected along three transects from the inlet to the outlet, with six samples in each transect. In order to measure the soluble P, an NH4Cl extraction was done. This was also analysed for total soluble P after oxidation with peroxodisulphate.

Biogas is increasingly used for fuel in for example vehicles and it´s produced in a biogas processconsisting of the steps of pretreatment, digestion and gas cleaning. The pretreatment is a method usedto increase the gas production and / or destroy pathogens. The digestion is the stage when anaerobicmicroorganisms convert bio-mass of a substrate to a raw gas containing about 65% of methane. Thegas cleaning is used to increase the methane content to about 97% so the gas can be used for motors invehicles. The biogas part of the Ekeby sewage plant in Eskilstuna is using multiple substrates.

Byggandet av dagens sjukhus har blivit allt mer komplext. När det kommer till uppbyggnaden av stomkonstruktionen har kraven för vibrationer ökat. För att säkerställa kraven för stomvibrationer måste pågjutningens tjocklek öka med ca 90 mm från standarden som är ca 40 mm. Att utföra denna extra pågjutning är inte ett problem i sig, utan den extra torktiden som tillkommer. Den extra torktiden är inte det enda problemet.

When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

The main purpose of this project was to make a survey of the steam and electricity consumption at Akzo Nobel Functional Chemistry AB and give suggestions of how to minimize them. These three different areas were focused on. First to make a survey of all the most important consumers, second to find the electricity consumption of the air compressors and the amount of waste heat produced from them. The third area was to calculate a model of how much fresh water that is used during a cooling sequence in the water based heating/cooling system of the reactors and give a suggestion of a suitable reuse for this water.The main result is a total survey of the energy consumption in steam and electricity. The survey shows that the second largest group after Drying is heating of ventilation which gives big potentials of reducing the total steam consumption if there is a way of being self supporting in ventilation heat.

This thesis aims to examine the viability of various techniques for increased electricity generation in CHP plants and the effect of electricity price fluctuations on the profitability.The techniques examined are fuel dryer, pellet production, methane production, combined methane- and pellet production, seasonal heating storages in caverns and pit heat storages and condensing tail. Using Excel and Matlab, the prerequisites for investment costs, revenues and expenses were calculated.What affects the price of electricity is a combination of economic and technological development, energy prices, economic structure, population changes and weather. Different scenarios for the electricity price were therefore examined. In the base case, the electricity price was given by the Nord Pool electricity price statistics of area three in 2011. Thereafter, WiMo was used to design the electricity scenarios for 2030, which was then applied to the data to obtain the viability of various scenarios. The techniques examined were found to give greater profits to the CHP plant by increasing and optimizing the production of electricity.

When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

Lining techniques such as nap bonding and mist lining were developed in the late 20th century and have gained popularity alongside with the increased use of acrylic emulsions as adhesives. The ability of the adhesive to create a nap bond to the canvases without penetrating the fibers has shown advantages regarding reversibility. In addition, the use of moisture, heat and pressure is reduced, which can be advantageous for more sensitive paintings. These lining techniques have been included in several studies where reversibility, minimal intervention and respect for the individual requirements and problems of each object have been the focus. The adaptability of the methods has been confirmed and to further explore the adaptability, this study consists of three simpler application techniques with the adhesive Lascaux 303 HV on mockups.

The moisture content in 10 deliveries of tree parts and 10 deliveries of wood residues were measured with different methods to analyze the quality of procedure used at Dåvamyran today. At the same time a survey was made on the measure procedures used at heating plants in Sweden The majority of the heating plants in Sweden use weight and moisture content as base for payment but at some plants only volume. The moisture content is usually estimated by Drying wood chips in an oven but few plants a visual estimation is used. At few plants moisture content is estimated spectroscopicily. The techniques using near infra read light and other electromagnetic are still at a test stage. The methods of measurement used today are quit unreliable for the individual deliveries and there is a risk for systematic mistakes.

Future climate changes may lead to an interest of alternative and foreign forest tree species in order to spread the risks in forestry. Douglas fir, Sitka spruce, Freemont cottonwood and hybrid aspen are examples of popular foreign tree species that along with western red cedar could have a future in the Swedish forests.Södra Skogsägarna and SLU have collaboration in establishment of foreign species in Swedish forests.The purpose of this study was to analyze and present the establishment of western red cedar, and to survey and illustrate injuries of freeze Drying and other damages like deer browsing, vegetation and insect attacks. The study included four different provenances, and spruce as a reference, planted in two locations ? Asa and Släne.Western red cedar is despite its name a conifer of the cupressaceae family with defined secondary characteristic and gets along well with an overstory. Western red cedar grows often in mixed stands with similar conifers and its natural habitat is within and in the area near to British Columbia.The study included two series of field inventories, one made in the summer and one in the autumn 2013, three growing seasons after plantation.

To regularly remove woody vegetation along the roadside of forest roads is an important part of the road maintenance, since the vegetation binds moisture in the road side and, thus, the removal makes the road Drying faster with results in improved bearing capacity. Vegetation removal also makes it easier to upgrade the road by material recycling from the ditch and, moreover, the visibility along the road is maintained.The aim of the study was to evaluate what type of chain flail is the best and most cost-effective for removal of different kind of woody vegetation along forest roadsides.Time studies were made on two chain flails when removing woody vegetation in three different classes; easy-, middle- and heavy shrub removal. The studied flails were one light and rather simple flail named Optimal M160 and a heavier and more advanced flail named Slagkraft H210. The removal was made according to Holmen Skogs? specification and the quality of the cleaning was measured by objective belt inventory.The productivity was higher with the heavy flail within all cleaning classes.

This study aimed to evaluate the levels of formaldehyde and organic acids that can build up within enclosed spaces. Another goal was to compare two types of paints that can be used as coating barriers within showcases and in turn compare them to the modern, and by many highly recommended, material of Marveseal®. A low volatile waterborne alkyd/acrylate paint and a two component polyurethane paint was compared to Marveseal® in two series of experiments. One series measured the level of formaldehyde, and thus the effectiveness of the three chosen barriers, and the other series measured the level of volatile organic acids, both the acids emitted from the paint itself, and that of the wood. One box in each series were not treated at all and was used as a reference.The fact that different types of materials emit volatile organic compounds have long been known.