AbstractThe tests work is about the subject "synergism of steel and concrete."The construction sector is in a strong competition and the different companies in the PrefabMarket has ever tried to develop new design solutions that are efficient and environmentallyfriendly.The purpose of this report is to highlight different aspects of interaction and size up a columndimension and to examine its efficiency and load capacity as Eurocode 3 and Eurocode 4. A sizing chart that describes the relationship between the torque and normal force shouldalso be made of the interaction . .

The purpose of this of this essay is to explore the construction of a conservatory that is livable allyear around. When you build a conservatory there are several factors that need to be regardedthat usually are of no importance when you build a regular conservatory. The glassed facadeneeds to have a very good U-value and all the parts of the facade need to be isolated and theconstruction needs to prevent thermal bridges.In this essay we will start by looking at the shape of the conservatory. Due to the façade consistsof glass the conservatory will need to have a good ratio between the area and the façade so thatthe heat losses will be at a minimum. However, due to the fact that one of the sides of the façadeis connected to the warm house, you quickly realize that the shape of the conservatory is of noimportance.There are two common ways to build a foundation for a conservatory, a molded concretefoundation and isolated wooden beams.

This master thesis consists of the creation of shock absorber models for percussive rock drills. A model of the rock was also developed. These models were connected to existing models of the rock drill to create a complete simulation of the rock drilling process.When the models had been created the rock model was evaluated by comparison with measured values from lab tests. The verified rock model was then used to evaluate the shock absorber models.Four new shock absorber concepts have been developed. Three of these have been modelled, while the fourth have only been sketched and described.The evaluation of the models showed the following:? Simulations of the single shock absorber don?t correlate to reality very well.

This master thesis is intended to give an increased understanding of the stress state in an axle, which is assembled in one of Atlas Copco?s mountain drilling rigs. The main problems investigated were how the axle is affected when the bearing is worn, when the pretension is varied, and how to dimension the axle. Answers to these questions were found by using hand calculations, practical testing and with Finite Element analyzes. The dimensioning of the axle is currently based on the bending stress, but the author?s opinion is that the axle should be dimensioned considering the equivalent stress.

As a newly graduated student in construction you rarely have as much knowledge as you wish you had. It is a complicated line of business that requires knowledge and understanding of both technical solutions and interaction between actors. It is impossible to be fully learned and with that much unknown it can be hard to know where to start. This report is one step in the right direction. It contains a planning that contains construction and installations for a one level house in Kiruna with its different choices motivated.

The report contains three parts. The first part is a summary and overall presentation of thermalcracks and preventing measures against such cracks. This is a theoretical part where theinterested designer can get acquainted with various alternatives, be guided to more detailedliterature, and receive some practical information regarding the design of the respectivemeasures.The second part deals with calculation of the risk for thermal cracks and design of water coolingas a limiting measure. Two complementary methods are reviewed for efficient calculation:?the handbook method CraX1(by Lulea University of Technology) is used for quickverification?finite differential analysis in the calculationtool ConTeSt Pro for more precise projectingHere is also presented a development of existing standards through design of the cooling systemby means of the Bernoulli equation.

In this report the balconies? abutments for a property in Bo01-area in Malmö has been studied. The property which is called Vitruvius contains four build-ings where two of them have corbelling balconies with intermittent abutments. With intermittent abutment means that the 50 mm thermal bridge insulation that the balconies is equipped with, is broken regularly by a 300 mm concrete heel. The reinforcement bar that holds the balcony runs through this heel.

This report is our Master thesis. Our work has taken place at a one-stop-shop in Sölvesborg during the spring of 2002. We have conducted ethnographical studies concerning the one-stop-shops frontdesk and telephone exchange. During these studies we became aware of some differences under which the daily work was to be carried out. When operating the switchboard the staff usually work alone and perform the tasks individually.

Vid dragprovning av lödningar framkom att i många fall är kopparledningen svagare än själva lödningen och brottet sker i kopparledningen eller i kabelskon. Undersökning av mikrostrukturerna visade att det bildas martensit i grundmaterialet i ett område under pinnlödningarna. Medelvärdet på martensitlinsens storlek beräknades till 10,69 mm i diameter och 0,73 mm i djup. På grund av att grundmaterialet påverkas bör pinnlödningar sättas minst 10 mm från varandra. Lödningar gjorda i -5°C visade inga tecken på försämrad kvalitet med avseende på lägre hållfasthet eller ökad martensitbildning.

Vid dragprovning av lödningar framkom att i många fall är kopparledningen svagare än själva lödningen och brottet sker i kopparledningen eller i kabelskon. Undersökning av mikrostrukturerna visade att det bildas martensit i grundmaterialet i ett område under pinnlödningarna. Medelvärdet på martensitlinsens storlek beräknades till 10,69 mm i diameter och 0,73 mm i djup. På grund av att grundmaterialet påverkas bör pinnlödningar sättas minst 10 mm från varandra. Lödningar gjorda i -5°C visade inga tecken på försämrad kvalitet med avseende på lägre hållfasthet eller ökad martensitbildning.

The Swedish cooperative Lantmännen Ekonomiska Förening has initiated a project labelled "Operation Blåljus" that includes an extensive program for closing down elevators. The number of elevators will be reduced from 92 to approximately 15 after harvest of 2007. The objective of Blåljus is to increase the price of grain with 10 öre/kg. A project has been initiated at the Lantmännen Grain division where the purpose is to provide the farmers with support in their decisions and practical advice how they can load a 35 ton grain truck on 30 minutes. The result from the project will serve as a support system to the farmer in his ambition to achieve cost efficient systems to load a truck with grain on the farm.

The aim of this thesis is to use Gabriel Tardes theories concerning imitation, repetition and the public opinion as a way of understanding how transmedial communication develops over time. This involves a study of social media, traditional press and public organizations in relation to each other. The campaign, What are you doing? (Vad håller du på med?, 2013), launched by the Swedish military as a way of drafting more soldiers, is used as an example of how the theories can be applied to help us understand connections, patterns and social behavior in the rapid mutation and viral spreading of information. By discussing the campaign and its effects, the ambition is to give an understanding of how a campaign of this scale could be planned for and structured.

This report shows the process of the development of a sensor module for the seed drills of Väderstad Verken AB. The module is supposed to replace existing solutions, provided that it is better from both a constructional- and an economical aspect. The purpose of the sensor is to continuously give the driver information about the level of height of the front- and drilling tools and the main purpose of the sensor is to allow the seeds to be placed at the desired depth. The sensors which have been taken into consideration have all been of an analogue type and have a protection class of minimum IP67.The methods applied have been taken from the book ?The Mechanical Design Process? by David G.

This report deals with issues related to construction waste. Building material that has not been built into the project is defined as construction waste. Cost of construction waste amounts to 4-12 % of the total cost of the project. Moreover, cost of construction waste is 1-3 % of the production cost. The aim of this study is to increase knowledge about the main causes of waste within the construction industry.

In this study we try to focus on the costs for wear parts on different type of soil tillage machines and at Väderstad Rapid drilling machine. We have studied some of the leading types of cultivators and disk harrows. Among the cultivators we have investigated Väderstad Cultus, Dalbo Dinkomax, Horsch Tiger and Terrano. At disk harrow we have looked at Amazone Catros and Väderstad Carrier. We have made more detailed study on costs for wear parts, working depth, driving speed and diesel consumption.