This master thesis covers the seasonal planning of a small scale hydropower system. The system in this study is owned and operated by Mälarenergi Vattenkraft AB. The total system consists of 4 different main rivers with 24 hydropower stations and several dams. The total installed power in the system is 43.75 MW. Most of the hydropower stations are regarded as small scale hydropower stations and thus entitled to green certificates.In this report the issue of planning is formulated as an optimization problem.

In this report focus is put on the combustion process at a cement plant. Combustion is the heart of the cement making process and absolutely crucial to have under full control and well optimized. The fuel is put into the process through a burner pipe and this burner pipe is modified to reach a more efficient combustion. The primary target is to enable burning of heterogeneous alternative fuels and increase the production level. Other positive effects from this type of optimization is lowered specific fuel consumption and lowered CO2 emissions. A redundant burner is chosen for the project and overall the project steps are the following: 1. Installing a Jet air nozzle ring in a way so it can move both axially and radially due to temperature changes. 2.

In Sweden there is a large interest in renewable energy but the market for solar power is still small compared to other countries such as Germany. Here many farmers produce their own electricity. The Federation of Swedish farmers have acknowledged the potential for Swedish farmer to produce electricity and there is an interest among the farmers. The agricultural branches in Sweden most suitable for solar power are pig production and poultry due to the even electricity need throughout a year. Swedish pig farmers are going through a period of unsteady profitability which makes it interesting to see whether producing their own electricity can affect the economic situation.

Today electronics becomes more and more complex and to keep low costs and power consumption, both digital and analog parts are implemented on the same chip. The degree of automization for the digital parts have increased fast and is high, but for the analog parts this has not come through. This have created a big gap between the degrees of automization for the two parts and makes the analog parts the bottleneck in electronics develop. Research is ongoing at Electronics systems group at Linköping University target the increase of design automization for analog circuits. An optimizationbased approach for device sizing is developed and for this a good optimization method is needed which can find good solutions and meet the specification parameters.

Control of a diesel engine equipped with Variable Geometry Turbine (VGT) and Exhaust Gas Recirculation (EGR) requires a multivariable control method. One problem is that the engine system is non-linear. Furthermore there are strong cross-connections between inputs and outputs and the inputs have alsoboundaries. To be able to manage these control problems, MPC has been used that is a multivariable method. The MPC-controller consists of an optimization problem and therefore MPC can find the optimum control signals in an easy way.

Abstract. Title: Supply Chain Optimization ? for Sourced Production. Authors: Patricia Möller and Andreas Paulsson. Tutors: Jan Eskil Hollen ? Business Developer, Lilleborg as, Orkla, Everth Larsson ? Department of Industrial Management and Logistics, Division of Engineering Logistics, Lund University, Carl-Henric Nilsson ? Department of Economics and Business Administration, School of economics and management, Lund University.

The thesis aims to examine how companies optimize the human capital from a value creation perspective. The value creation will be related to transfer of knowledge, recruitment, staff turnover and development. The thesis has a deductive approach and six qualitative interviews have been conducted. The results from the interviews will be strengthened with a quantitative data analysis of two measurements; value added per employee and human capital efficiency. The theoretical framework includes definitions of human capital.

The wastewater treatment plant at GE Healthcare's facility in Uppsala deployed a three step vacuum evaporator in 2007. The purpose of this was to pre-treat wastewater containing amines. The purpose of this thesis was to optimize thisprocess by reducing the amount of concentrate without releasing more nitrogen tothe environment and to examine if density could be used as a measurement of whenthe process should be ended.To create a foundation for optimization six test cycles were conducted with samples taken from all three steps. Both concentrate and condensate were tested as well as the incoming solution. Furthermore, the thesis has been expanded with a benchmarking part examining two different evaporators.

The aim of this study was to develop a load prognosis model for Uppsala district heating system to be used as a tool for heat production optimization. The methodwas to build three models for the different customer types; housing, industry andoffices and then scale them for the total system using data from Uppsala districtheating system. The heat load consists of two parts, one that is temperaturedependent and one that is dependent of the social behavior of the customers. Thetemperature part was modelled with an ARX model using an outdoor temperatureprognosis as input signal. The social behavior part was modelled using the mean ofthe social behavior from some days before and additionally by distinguishing betweenweekdays and weekends.

This report describes the master thesis project ?Weight Optimization of a Composite Chassis for a Multimodal Lightweight Vehicle? which is a part of the Master program in Naval Architecture and a part of a research project at the Centre for Naval Architecture, KTH. Demands on smart and energy efficient transport solutions are continuously increasing. In the Stockholm region the citizens are expected to increase with 25% and the road vehicles with 80% until 2030, putting high demands on the traffic system. Using a small multimodal vehicle deals with this problem and uses both the land and waterways for transportation.

The thesis aims to examine how companies optimize the human capital from a value creation perspective. The value creation will be related to transfer of knowledge, recruitment, staff turnover and development. The thesis has a deductive approach and six qualitative interviews have been conducted. The results from the interviews will be strengthened with a quantitative data analysis of two measurements; value added per employee and human capital efficiency. The theoretical framework includes definitions of human capital.

Active immunization against gonadotropin-releasing hormone (GnRH) is an alternative to surgical castration of male pigs to avoid boar taint. The aim of this study, including 128 pigs, was to evaluate the effect of a GnRH-vaccine Improvac® on performance and on social and sexual behaviour. Male pigs were assigned to three treatments; surgical castration at four days of age, immunization against GnRH and no castration. Vaccination was performed eight and four weeks before slaughter. Surgically castrated male pigs had significantly lower daily weight gain during the suckling period than entire male pigs (235 vs.

Powder Metal (PM) gears are machine element components which operate under the same principle as conventional gears, but, due to their intrinsic material characteristic need to be designed slightly different, and its manufacturing process offers advantages previously unobtainable by conventional steel gear manufacturing methods. The use of PM in similar applications, such as synchronous hubs, makes them a suitable candidate for production in such material. The current master thesis work focuses on gear design using PM by utilizing finite element method (FEM) to reduce weight and inertia taking into account root bending strength and tooth deflection.First a topological optimization is used to determine feasible candidates for different web designs which have as objective to reduce volume, similar topologies were shown during different loading conditions; and hence, this topology was chosen as a suitable candidate. A shape optimization of the topological candidate was performed having as state variables root bending strength, independent for compressive and tensile side of the tooth loading; and tooth deflection, which in concept can be correlated to static transmission error (TE).Another aspect in this thesis analysed is the possibility to incorporate non-trochoid root geometry, a trochoid root is always present when machining with a hob, into the gear root and hence reduce the stress concentration here. Due to the use of PM, a non-symmetric optimized root can be achieved and hence be optimizing compression and tension.Results showed significantly lower inertia, for example certain results showed 40% reduced when compared to solid gear, with adverse effects as increase in tooth deformation and increase in maximum principal stress.

Oilseed rape crops are an important in southern Sweden because of the high intensity of wheat growing. Pollen beetles are the most important pest in oilseed rape and causes often economic losses. Therefore it?s of great importance that we can control the population density, e g by using insecticides if necessary, to avoid mayor yield losses. In year 2000 pollen beetles were numerous in the province of Östergötland. The farmers sprayed with insecticides several times, but with low effects on the beetles. Field trials and laboratory experiments showed that pollen beetles had developed resistance against pyrethroids.

Scintigraphic examination of the esophagus has for some time been the method of choice for the study of motility dysfunction in humans. The method has not yet been described for horses hence the lack of reference values for passage time for a bolus through the esophagus in healthy subjects. The purposes of this study were to measure passage velocity and time for a bolus to pass through the esophagus in healthy subjects, as well as to evaluate the reproducibility of the method. Eight warm-blooded trotters were used in the study. The horses were sedated with a low dose of Acepromazine prior to onset of the study.