This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This study was performed in collaboration with Moelven Skog AB, Örebro district. The purpose of the study was to review existing literature in order to describe the current status of harvester based measurement technology as the way to provide information for calculating payment to the forest owners. In addition to this, a short survey was conducted to find out how a switch to harvester based measurement would affect the administrative workload on timber purchasers working for the district. The literature study shows that the harvester measurement technology is ready to use if it is combined with well-established routines for control of the harvesters, methods for automatic quality indexing of the timber and ways of creating pricelists specially adapted for harvester measurement. Pricing each stem seems to be the most promising method. Stem pricing has several benefits.

Large amounts of birch-timber are imported to Sweden, from particularly the Baltic States, since the domestic production can?t support the pulp industry. The goal of this study was to show the potential of birch and the area?s most suitable for birch production. The study was limited to Gävleborg County. Using site characteristics, site index (SI) for birch was estimated on all National Forest Inventory plots in Gävleborg County.

The project was performed at SiemensIndustry Drive Technologies with theobjective to provide actual values forthe energy savings potential withinSiemens scope of practice.In Sweden the electrical drives standfor about 30 % of the total electricityconsumption and about 60 % of theelectricity consumption within theindustry. During the pre-study phaseelectrical drives with pump applicationswere identified as large energy users.Because of this a case study at one ofSiemens customers, Stora Enso Fors wasperformed. The system that was evaluatedduring the case study was a throttledsystem with a centrifugal pump forpumping pulp.The results yielded that a saving ofover 50 % could be achieved by replacingthe throttle valve with a variable speeddrive, a frequency converter. Thepayback period was two years and twomonths and the present value for thetotal life cycle cost of the variablespeed system was 662.566 SEK lower thanfor the throttled system. As aconsequence, Stora Enso Fors is advisedto invest in a frequency converter forregulation of the system.The general conclusion is that a focuson system efficiency is the mostimportant factor in energy efficiencyprojects and that the system regulationmethod has a large impact on the overallsystem losses and hence its efficiency.Energy efficiency potential forthrottled systems with centrifugal pumpsis large and significant economicalsavings can be made through investmentswith short payback time..

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

This thesis describes possibilities for Metso Paper to lower their costs of spray pipes for their pulp wash press TRPE, with maintained good functionality and quality.Information that can be used by competitors has been censored in this version of the essay.To find solutions, alternative suppliers have been contacted and asked to quote. There has also been a new spray pipe designed. The manufacturing costs of the new design have been calculated.The thesis also contains a concept generation of an alternative product to the spray pipes in installations where a high pressure washer is used.To be able to ask other manufacturers of spray pipes to quote, a demand specification based on the currently used spray pipe was made. This was then sent to two alternative suppliers.An investigation of earlier used spray pipes, and the currently used, shows that the nozzles are a big part of the total costs of the spray pipes. To attempt to reduce the nozzles high cost an concept generation was made to find the best solution for a new design.There was a request that it should be possible to change the internal brushes in the spray pipe without cutting and welding.

According to Food and Agriculture Organization newsprint is defined as: Uncoated paper, unsized (or only slightly sized), containing at least 60 percent of mechanical wood pulp. The consumption of newsprint in Sweden was just over 798 000 tonnes in 2009, which represents approximately 90 kg per person. Although there are studies that predict a drastic reduction in newsprint consumption in the Western world, there seems to be a clear difference between forecasts for the future given by statistical analysis of newsprint consumption and forecasts given by experts in the industry. The former predict a continuing increase while the experts see a coming decrease in consumption.In this report, both demand and business strategies of newsprint in Sweden are studied. The study also presents a forecast of the future which is based on historical data and qualitative interviews.

In public libraries there seems to be an unspoken consensus on what literary quality is. At the same time librarians are always eager to express the opinion that quality lies in the eye of the beholder. Quality is, it is said, something that you don t have to define. But at the same time it s up to everyone to decide what quality means to them. What I have been missing from the discussion in libraries about literary quality is a theoretical awareness about what it means to divide literature into higher and lower spheres.

In Sweden, the demand for bio energy has increased in recent years due to the current energy and climate debate. In 2008, the energy supply of Sweden was 612 TWh, biofuels accounted for 123 TWh of these. Stumps have been highlighted as a potential fuel in recent years and the Swedish Forest Agency expects a technically and biologically feasible potential of 20.7 TWh annually between 2010 and 2019. The idea of utilize stumps is not new. During the 19th century stumps were used for tar production and during the 70?s and 80?s attempts were made to use stumps in the pulp industry.

Fuel pellets are in Sweden mainly produced from sawdust and cutter shavings. Before the pelletising process the raw material is dried to attain consistent moisture content and ground up in a hammer mill. In the densification process (pelletising) the ground material is forced through holes in a rotating die. This heats up the wood particles which cause them to soften and self bond. After the process the pellets are cooled, sieved and bagged. The milling process creates a wide range of particle sizes.

When the Swedish Forestry Act was changed in 1994, brushing of young stands became non mandatory. Since then the annual need for brushing in the country has increased by about 100 000 hectares per year. In later years the price for biomass energy has increased to the same level as pulp wood. The high price on biomass energy and the large areas of stands in the need of brushing has created a new market with its own technical, economical and environmental conditions. There is a development of various techniques to manage the forestry stands with late brushing.